• Structural Engineering and Mechanics
• /
• v.18 no.5
• /
• pp.691-707
• /
• 2004

This paper presents the micro-mechanical modeling for predicting concrete behavior under compressive loading. The model is able to represent the heterogeneities in the microstructure up to three phases, i.e., aggregate particles, matrix and interfaces. The smeared crack concept based on non-linear fracture mechanics is implemented in order to formulate the constitutive relation for each component. The splitting tensile strength is considered as a fracture criterion for cracking in micro-level. The finite element method is employed to simulate the model based on plane stress condition by using quadratic triangular elements. The validation of the model is verified by comparing with the experimental results. The influence of tensile strength from both aggregate and matrix phases on the concrete compressive strength is demonstrated. In addition, a guideline on selecting appropriate tensile strength for each phase to obtain specified concrete compressive strength is also presented.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.36-39
• /
• 2002

Polycrystalline silicon (poly-Si) thin film transistor (TFT) technology is emerging as a key technology for active matrix liquid crystal displays (AMLCD), allowing the integration of both active matrix and driving circuit on the same substrate (normally glass). As high temperature process is not used for glass substrate because of the low softening points below 450$^{\circ}C$. However, high temperature process is required for getting high crystallization volume fraction (i.e. crystallinity). A poly-Si thin film transistor has been fabricated to investigate the effect of high temperature process on the molybdenum (Mo) substrate. Improve of the crystallinity over 75% has been noticed. The properties of structural and electrical at high temperature poly-Si thin film transistor on Mo substrate have been also analyzed using a sputtering method

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.738-742
• /
• 1996

In the present paper, We have tried to reconfirm the "Interlligent" material properties using both the sintered TiNi/A(1100) matrix composite by powder metallurgy method. By using these specimen, Shape meorystrengthening effect in tensile strengthand fatigue crack propagation above inverse transformation temperature of TiNi fiber were investigated. More over, by SEM obsevation, the effect of the residual stress at the interface between A1 matrix and TiNi fiber and some brittle precipitation layers such as inter metallic compounds on fracture mechanisms was metallurgically discussed.discussed.

• Steel and Composite Structures
• /
• v.9 no.6
• /
• pp.499-518
• /
• 2009

The present paper investigates the stochastic seismic responses of steel structure systems with Partially Restrained (PR) connections by using Perturbation based Stochastic Finite Element (PSFEM) method. A stiffness matrix formulation of steel systems with PR connections and PSFEM and MCS formulations of structural systems are given. Based on the formulations, a computer program in FORTRAN language has been developed, and stochastic seismic analyses of steel frame and bridge systems have been performed for different types of connections. The connection parameters, material and geometrical properties are assumed to be random variables in the analyses. The Kocaeli earthquake occurred in 1999 is considered as a ground motion. The connection parameters, material and geometrical properties are considered to be random variables. The efficiency and accuracy of the proposed SFEM algorithm are validated by comparison with results of Monte Carlo simulation (MCS) method.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.3
• /
• pp.257-261
• /
• 2009

In this study, we have researched the optimum design method of the lenticular lens sheet for 3D displays on a TFT-LCD panel, to offer a more stable stereoscopic image, improved 3D quality, and a wider viewing zone. Especially, we have defined the viewing zone width (a parameter denoted as Z) to apply it to the optimum design. The results of this new design method have been compared with the existing design method. As a result, it is revealed that the proposed design method improves the stereoscopic image quality by reducing the black matrix zone width.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.853-854
• /
• 2006

Warm compaction powder metallurgy was used to produce a $Ti_3SiC_2$ particulate reinforced Cu matrix composite. Fabrication parameters and warm compaction behaviors of Cu powder were studied. Based on the optimized fabrication parameters a Cu-based electrical contact material was prepared. Results showed that in expend of some electrical conductivity, addition of $Ti_3SiC_2$ particulate increased the hardness, wear resistivity and anti-friction ability of the sintered Cu-base material.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09b
• /
• pp.1290-1291
• /
• 2006

Fabrication of $Fe_3AlC$ matrix in-situ composite, reinforced by a FeAl phase, was studied by using the powder metallurgical processing route. Especially, in order to disperse the second phase more finely, we chose the mechanical alloying process. We investigated the microstructural and mechanical properties of the consolidated material. After consolidation by vacuum hot pressing, the compact showed almost full density and consisted of a $Fe_3AlC$ matrix and FeAl second phase (average particle size was less than 1m). The compact showed HV746, which was higher than that of the arc melted $Fe_3AlC$ monolithic material, HV603.

• Proceedings of the Korean Fiber Society Conference
• /
• 2001.10a
• /
• pp.440-443
• /
• 2001

Polymer/layered silicate nanocomposites have recently received considerable attention from both academia and industry as an effective way to overcome the shortcomings of conventional polymer. When the silicate layers are exfoliated and randomly distributed in polymer matrix, the nanocomposites exhibit improved mechanical, thermal and barrier properties. (omitted)

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.4
• /
• pp.426-431
• /
• 2004

We have studied the pressure-dependent liquid crystal's dynamics in a twisted nematic (TN) liquid crystal panel with thin film transistor by applying an external pressure to it. When the external pressure is applied to the panel in a dark state, the disclination lines were generated as a light leakage whereas they did not appear in a simple test cell that has only pixel and common electrodes. It was because the disclination lines were Provoked by the electric field between pixel electrode and data/gate bus line for active matrix driving. Consequently, the external pressure resulted in dynamic instability of the liquid crystal so that the disclination lines at the data/gate bus line intruded into the active area.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2019.05a
• /
• pp.118-119
• /
• 2019

The exterior finish not only has a relationship to the functionality of building, but also the spatial aesthetics and visual perception. Common exterior finishes are wood, stone or acrylic based and etc. However, these finishes have different attributes which can alter the quality of the architecture, such as durability, moisture and fire resistance. To make up for the short-comings of these materials, we have used iron based resources for optimization. However, iron materials are expensive, so they have limitations in general use. In this study, we have experimented with various forms of exterior finishes using cement, which is the most efficient and widely used building material with several economic advantages. We experimented with different materials to use as the formwork for the gloss of the cement matrix. As a result, the gloss show that order of urethane, steel, and wood material.