• 터널과지하공간
• /
• 제17권3호
• /
• pp.175-185
• /
• 2007

불연속면을 따라 점토 등의 충전물이 포함된 경우에는 불연속면의 방향이 유리하게 작용하더라도 사면안정에 불안정성을 초래한다. 연구지역의 사면활동은 점토충전물과 풍화토의 경계를 따라 발생하였다. 이것은 물성의 차이를 보이는 경계부분이 존재했기 때문이며, 암석에서 엽리 등이 구조적 운동시 연약대로 작용하여 층간의 미끄러짐을 유도하는 현상과 매우 유사하다. 대부분의 해석에서 점토충전물이 존재할 경우에는 하나의 불연속면으로 설정하여 해석한다. 이때의 불연속면은 점토층내에서의 활동면으로 해석되므로 점토와 원지반과의 경계부의 특성이 해석에 고려되지 못하여 불연속면의 거동은 결국 점토의 물리적 성질에 많이 지배된다. 점토충전물로 인한 활동사면의 안정성 평가 결과는 충전물에 의한 불연속면의 파괴유형에 따른 강도정수에 의해 안전율에 상당한 차이를 보인다.

• 한국지진공학회논문집
• /
• 제13권3호
• /
• pp.21-28
• /
• 2009

지반-말뚝-구조의 상호작용을 정밀하게 해석하기 위해서는 토층, 말뚝 그리고 구조물의 적절한 묘사가 필요하다. 일반적으로 사용하는 유한요소해석의 경우에는 지반이나 구조물의 물성이 바뀌는 경계를 따라서 요소의 경계가 정해지게 된다. 그러나 실제로는 토층 단면과 말뚝의 형상이 매우 복잡하여 요소의 배열이 매우 어려운 작업이 될 수 있다. 이 어려움을 해결하기 위하여, 이 논문에서는 불연속선의 위치에 관계없이 규칙적인 요소를 사용하여 쉽게 적분을 가능하게 하는 다른 적분 방법을 채택하였다. 이 방법을 적용함으로 써 요소는 매우 빠르고 규칙적인 강성 매트릭스를 만든다. 구조물 응답에 대한 토층과 말뚝의 영향을 조사하였고, 예를 통하여 본 방법의 유효성을 보였다. 탄성 말뚝의 사용으로 20% 대의 가속도 감소 효과를 얻었고 지반 층의 모양에 따라 그 영향이 변하는 것을 확인하였다.

• 한국지진공학회논문집
• /
• 제9권6호
• /
• pp.67-73
• /
• 2005

엄밀한 지반-구조물 상호작용 해석을 위해서는 지반에 대한 묘사가 적절히 이루어져야 한다. 그러나 물성이 불연속적이거나 지층의 모양이 복잡할 때에는 유한요소망을 구성하는 것이 어려운데, 그 이유는 유한요소망이 지층의 모양을 정확히 나타내어야하기 때문이다. 이러한 어려움을 극복하기 위하여 본 연구에서는 지층의 불연속선을 따라 요소를 재배열하지 않고 엄밀하게 수치적분이 가능한 방법을 채용하였다. 그 결과로 정렬된 요소망을 그대로 이용하게 되어 강성행렬의 성질이 좋아지며, 해석 또한 신뢰성이 높아지게 되었다. 이 해석 방법을 이용하여 지진응답에 미지는 지층의 영향을 조사하였으며, 결과적으로 복잡하고 불연속적인 물성을 가지는 지층으로 이루어진 지반과 구조물의 상호작용을 해석하는 데에 쉽게 이용 될 수 있음을 보였다.

• 소성∙가공
• /
• 제16권7호
• /
• pp.530-537
• /
• 2007

This paper is concerned with the analysis of plastic deformation of bimetal co-extrusion process. Two sets of material combination have been adopted for analysis, i.e. combinations of Cu/Al and Fe/Al. In the first set of material combination, the selected materials are AA 1100 aluminum alloy as hard material and CDA 110 as soft one. This type of material selection is to examine the effect of hard core and soft sleeve and vice versa on the deformation pattern in terms of plastic zone and velocity discontinuity along the contact surface between construction materials. Four different cases of co-extrusion process in terms of material combination and interference bonding were simulated to investigate the effect of material arrangement between core and sleeve, and of bonding on the plastic zones and velocity discontinuity. In the other set of material combination, model materials used as core and sleeve were AA 1100 and AISI 1010, which are relatively soft and hard, respectively. Process parameters except diameter ratio of core to sleeve material such as semi-die angle, reduction in area in global sense and die comer radius have been set constant throughout the simulation to concentrate our effort on the analysis of influence of diameter ratio on deformation behavior such as deformation zone, surface expansion, exit velocity discontinuity between composite materials, and extrusion forces.

• Coupled systems mechanics
• /
• 제7권6호
• /
• pp.669-690
• /
• 2018

This paper deals with numerical modeling of dynamic failure phenomena in rate-sensitive brittle and/or ductile materials. To this end, a two-dimensional continuum viscodamage-embedded discontinuity model, which is based on our previous work (see Do et al. 2017), is developed. More specifically, the pre-peak nonlinear and rate-sensitive hardening response of the material behavior, representing the fracture-process zone creation, is described by a rate-dependent continuum damage model. Meanwhile, an embedded displacement discontinuity model is used to formulate the post-peak response, involving the macro-crack creation accompanied by exponential softening. The numerical implementation in the context of the finite element method exploiting the second-order mid-point scheme is discussed in detail. In order to show the performance of the model several numerical examples are included.

• 터널과지하공간
• /
• 제5권2호
• /
• pp.104-113
• /
• 1995

Shear strength of the discontinuity on which the pre-failure of rock slope was occurred during surface excavation was measured through the direct shear test using core samples obtained in-situ. Internal friction angle was increased as the roughness of discontinuity surface(JRC) was increased. Results of the tilt test using core samples of higher JRC also showed very similar trend as those of the direct shear test. When the samples replicated from natural cores were used int he tilt test, results of friction angles showed almost perfect continuation of the residual friction angles from the direct shear test. However, when the gouge material existed in the discontinuity the internal friction angle strongly depended upon the rate of filling thickness to the height of asperity irrespective of the JRC. Based on the results of both direct shear test and tilt test internal friction angle and cohesion of discontinuity, which reflect the in-situ conditions fo pre-sliding failure and also can be used for the optimum design of support system, were assessed. Two kinds of support measures which were expected to increase the stability of rock slope were considered; lowering of slope face angle and installation of rock cable. But, it was found that the first method might lead to more unstable conditions of rock slope when the cohesion of discontinuity plane was negligibly low and in that case the support systems of any kind which could exert actual resisting force were needed to ensure the permanent stability of rock slope.

• Ocean and Polar Research
• /
• 제32권3호
• /
• pp.331-336
• /
• 2010

The CREAMS (Circulation Research of the East Asian Marginal Sea) survey in 1999 revealed a sharp mid-depth discontinuity of the phosphate:silicate ratio in all basins of the East/Japan Sea. Incidentally, this discontinuity layer corresponds to the oxygen minimum layer. Directly below the discontinuity layer, oxygen concentration is increased. This increase in oxygen concentration is interpreted as a proof of intermediate water formation. Oxygen minimum indicates that the water parcel is old and stable against mixing. So it seems be an efficient barrier to vertical exchange of materials. This means that, once materials enter the lower domain, they rarely return to the upper domain. Therefore, the biogeochemistry of the East/Japan Sea depends heavily on material input through the Korea Strait, and flux is expected to be sensitive to the climate change. As a result, the East/Japan Sea ecosystem seems vulnerable to tipping (regime shift), which occurred on a decadal time scale.

• 한국안전학회지
• /
• 제21권3호
• /
• pp.87-93
• /
• 2006

When a structure is constructed at the site composed of soil, the behavior of a structure is much affected by the characteristics of soil. Therefore, the effect of soil-structure interaction is an important consideration in the design of a structure at the site composed of soil. Precise analysis of soil-structure interaction requires a proper description of soil profile. However, most of approaches are nearly unpractical for soil exhibiting material discontinuity and complex geometry since those cannot consider precisely complicated soil profiles. To overcome these difficulties, an improved integration method is adopted and enables to integrate easily over an element with material discontinuity. As a result the mesh can be generated rapidly and highly structured, leading to regular and precise stiffness matrix. The influence of soil profile on the response is examined by the presented method. It is seen that the presented method can be easily used on soil-structure interaction problems with complicated soil profile and produce reliable results regardless of material discontinuities.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2006년도 정기 학술대회 논문집
• /
• pp.365-372
• /
• 2006

A new meshfree formulation is developed for material discontinuity problems. A local interfacial jump function which is defined as hyperplane function is embedded in the meshless approximation and the approximation accurately models functions with jumps in the displacement and the derivative fields. Diffuse derivative technique copes with difficulty due to complexity of derivative computation of meshfree approximation. Collocation method with diffuse derivative accelerates computing speed for numerical solution. By solving inclusion and composite material problems, the robustness and effectiveness of the method are verified.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제9권1호
• /
• pp.190-207
• /
• 2015

In the combustion engineering, to decrease pollution and increase production efficiency, and to optimally keep solid burning material amount constant in a burner online, it needs a smart method to detect the amount variation of the burning materials in a high temperature environment. This paper presents an online machine vision system for automatically measuring and detecting the burning material amount inside a burner or a boiler. In the camera-protecting box of the system, a sub-system for cooling is constructed by using the cooling water circulation techqique. In addition, the key and intelligent step in the system is to detect the pile profile of the variable burning material, and the algorithm for the pile profile tracing was studied based on the combination of the gey level (color) discontinuity and similarity based image segmentation methods, the discontinuity based sub-algorithm is made on the quaternion convolution, and the similarity based sub-algorithm is designed according to the region growing with multi-scale clustering. The results of the two sub-algoritms are fused to delineate the final pile profile, and the algorithm has been tested and applied in different industrial burners and boilers. The experiements show that the proposed algorithm works satisfactorily.