• Tribology and Lubricants
• /
• 제37권5호
• /
• pp.164-171
• /
• 2021

Ultrasonic sensors show various reception characteristics based on the density of the measurement medium; hence, they are used in various fields to benefit from the characteristics of ultrasonic signals. In this study, the reception characteristics according to the thickness of the first matching layer are compared and analyzed for application to gas tank microleak detection. Accordingly, three types of sensors are manufactured with varying thicknesses of the first matching layer, namely 4.8 mm, 5.1 mm, and 5.5 mm; further, a direct measurement method is used wherein the sensor is attached to the inside of the chamber. Experiments are conducted to observe the phase change due to microleakage, which is the most linear in the sensor with the 4.8 mm thick first matching layer. This is assumed to be the result of stable signal transmission and reception with little phase deviations over time because the first matching layer is closest to the ultrasonic wavelength. The other sensors show nonlinear results with increasing thickness of the first matching layer. Through this study, it is found that appropriately selecting the thickness of the first matching layer of the ultrasonic sensor can greatly influence sensor reliability.

• 센서학회지
• /
• 제27권6호
• /
• pp.374-379
• /
• 2018

The piezocomposite transducer is widely used because it is highly efficient in transforming electric energy into mechanical energy, and its frequency range is broader than that of other types of ultrasound transducers. A general piezocomposite transducer is composed of an acoustic lens, impedance matching layers, piezoelectric materials, and backing layers. When an input voltage is applied to a piezoelectric material as an active material, it generates sound waves while vibrating. At that time, an impedance matching layer helps the sound waves to propagate forward while reducing the impedance mismatch that may occur at the interface between the active material and its front material. The impedance mismatch has a negative effect on the signal of an ultrasound transducer; thus, it is important to design a matching layer to overcome the issue. In this study, an optimized feature of a matching layer with gradient properties is studied. An objective function is defined to minimize both the average and the deviation of the reflection coefficients that are functions of the frequencies. As a result, an improvement in the signal characteristics with respect to the sensitivity and bandwidth is reported.

• 한국산학기술학회논문지
• /
• 제14권7호
• /
• pp.3191-3196
• /
• 2013

초음파 센서는 거리를 측정하는 센서이다. 초음파 센서의 피에조 세라믹과 매칭레이어 접착기술이 가장 핵심이 되는 기술이다. 본 논문에서는 초음파를 공기 중으로 발진해 주는 매칭레이어에 대한 관계의 연구와 함께 피에조 세라믹과 매칭레이어를 접착한 경우 변화될 수 있는 결과를 추출하여 제 2의 사용가능 주파수를 발견하는 것이 목적이다. 또한 실제 압전소자인 피에조 세라믹과 케미컬우드인 매칭레이어를 사용하여 실험하였다. 피에조 세라믹의 OD는 ${\Phi}50{\times}3T$로 설계 되었으며 매칭레이어 OD는 ${\lambda}=1/4$인 ${\Phi}62{\times}12t$로 설계하였다. 가장 최적의 공진 주파수는 53 Khz에서 음향 임피던스 값을 나타냈다. 실험결과, 유연성을 가진 접착제 보다 고체에 가까운 접착제를 사용할 경우에 많은 사용가능 주파수를 생성할 수 있는 결과를 얻을 수 있다.

• 수산해양기술연구
• /
• 제35권3호
• /
• pp.312-322
• /
• 1999

A ultrasonic transduce with a single acoustic matching layer has been designed as an attempt to increase the bandwidth of underwater transducer. The wideband resonance condition was accomplished by attaching a single matching layer on the front face of a ceramic resonator composed of a piezoelectric bar, a taper part and a head part. A modified Mason's model was used for the performance analysis and the design of transducers, and the constructed transducers were tested experimentally and numerically by changing the impedance and thickness of the matching layer in the water tank.The obtained results are summarized as follows:1. Measured resonant and antiresonant frequencies of the piezoelectric transducer with no matching layer in air were 24.7 kHz and 25.6 kHz, respectively. 2. Two resonant frequencies of the piezoelectric transducer with a single matching layer were 21.7 kHx and 26.9 kHz, respectively, in air and 21.4 kHz and 22.7 kHz, respectively, with a water load.3. Two distinct resonance peaks in the transmitting voltage response(TVR) of the developed transducer were observed at 22.0 kHz and 25.8 kHz, respectively, with center frequency of 24.0 kHz. The values of TVR at these frequencies were 130.1 dB re $1 \muPa$/V at 22.0 kHz and 128.5 dB re $1 \muPa$/V at 25.8 kHz, respectively.Reasonable agreement between the experimental results and the numerical values was achieved.

• E2M - 전기 전자와 첨단 소재
• /
• 제10권2호
• /
• pp.119-125
• /
• 1997

In this study, piezoelectric transducers were designed and manufactured using PZT-5A which had relatively high electromechanical coefficient, nondestructive testing system was developed which was able to inspect automatically using stepping motors, PC-Lab, and PC-Scope. The optimum design conditions for NDT were presented and verified comparing PZT-5A probes with comercial probes. It was proved by simulation and experiments that Epoxy is a good material as matching and backing layers. The envelope was reduced 60% with matching layer and 76% with matching and backing layer. NDT was successfully carried out for aluminum test pieces. Distance error of PZT-5A probe was 2.8%.

• 제어로봇시스템학회논문지
• /
• 제19권9호
• /
• pp.755-759
• /
• 2013

A broad-band underwater acoustic transducer that uses thickness vibration mode, derived from a disk type piezoelectric ceramic, has been proposed and designed for DVL (Doppler Velocity Log). Three different types of acoustic transducer were evaluated with respect to the transmitting voltage response, receiving voltage sensitivity and bandwidth of the transducer. The effect of the acoustic impedance matching layer and backing layer is discussed. The results demonstrated that three matching layer with lossy backing layer is the best configuration for underwater transducer. The trial underwater acoustic transducer with three matching layer has a frequency bandwidth of 55%, maximum transmitting voltage response of 200 dB and a maximum receiving voltage sensitivity of -187.3 dB.

• 한국전기전자재료학회논문지
• /
• 제31권6호
• /
• pp.408-411
• /
• 2018

We fabricated highly flexible Mn-doped $SnO_2$ (MTO)/Ag/MTO/polydimethylsiloxane (PDMS)/MTO multilayer transparent conducting films. To reduce refractive-index mismatching of the MTO/Ag/MTO/polyethylene terephthalate (PET), index-matching layers were inserted between the oxide-metal-oxide-structured films and the PET substrate. The PDMS layer was deposited by spin-coating after adjusting the mixing ratio of PDMS and hexane. We investigated the effects of the index-matching layer on the color and reflectance differences with different PDMS dilution ratios. As the dilution ratio increased from 1:100 to 1:130, the color difference increased slightly, while the reflectance difference decreased from 0.62 to 0.32. The MTO/Ag/MTO/PDMS/MTO film showed a transmittance of 87.18~87.68% at 550 nm. The highest value of the Haacke figure of merit was $47.54{\times}10^{-3}{\Omega}^{-1}$ for the dilution ratio of 1:130.

• 한국방송∙미디어공학회:학술대회논문집
• /
• 한국방송∙미디어공학회 2018년도 하계학술대회
• /
• pp.313-316
• /
• 2018

최근 미디어의 생성 및 소비 기술의 발전으로 몰입도 있는 콘텐츠에 대한 수요가 증가하고 있다. View Interpolation 기술은 두 개의 좌/우 영상을 기반으로 하여 두 영상의 중간 시점에 해당하는 영상을 생성해내는 기술이다. 먼저 Depth Hole Filling Module을 이용하여 좌/우 영상 및 그에 대응하는 깊이 지도를 입력으로 받아 깊이 지도에 존재하는 오류를 검출하고, 보정한다. 깊이 지도의 오류 보정이 완료되면, 해당 데이터를 각각 Feature Matching Module 및 Layer Dividing Module로 전달한다. Feature Matching Module은 실사 영상 내의 특징점들을 검출하고, 두 영상 내 특징점을 매칭하는 역할을 수행하며, Layer Dividing Module은 깊이 값을 기반으로 영상의 Layer를 분할한다. Feature Matching Module에서 특징점의 매칭이 완료되면, 특징점의 영상 내 좌표 및 해당 좌표에서의 깊이 값을 Distance Estimating Module로 전달한다. Distance Estimating Module은 전달받은 특징점의 좌표 및 해당 좌표에서의 깊이 값을 기반으로 전체 깊이 값에서의 이동도를 계산한다. 이와 같이 이동도의 계산 및 Layer 분할이 완료되면, 각 Layer를 이동도에 기반하여 이동시키고, 이동된 Layer들을 포개어 배치함으로써 View interpolation을 완성한다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1427-1429
• /
• 1997

In this study, piezoelectric transducer were designed and manufactured using PZT-5A which have relatively high electromechanical coefficient. A epoxy is a good material as matching and backing layers. The envelope was reduced 60% as using matching layer and 76% as using matching and backing layer. NDT was successfully carried out for aluminum test pieces. Distance error and resolution of PZT-5A probe were improved as increasing frequency. Envelope was effectively reduced by backing layer but sensitiveness was poor.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 춘계학술대회
• /
• pp.1966-1971
• /
• 2003

Matching inviscid and boundary layer methods are developed for hypersonic flow with thick boundray layer. The new equations match all the boundary layer properties with a variation in the inviscid solution near the edge, except for the normal velocity. Computational comparison are performed for incompressible and compressible flows over a flat plate. Results from the present method are compared with Navier-Stokes solutions. The present results are in good agreement with Navier-Stokes solutions. They show that the new technique can provide improved heating rates and skin friction predictions for preliminary design of vehicles where shear layers and entropy layer swallowing are important.