• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.39 no.4
• /
• pp.409-412
• /
• 2002

The LNA(Low Noise Amplifier) is designed for use in low cost commercial application covered fully IMT-2000 band(1920~2170MHz, BW=250MHz). It is optimized source inductance for source lead and designed to equivalent etched line. The LNA uses a high pass impedance matching network for noise match and simple structure. The bias circuit designs have been made self-biased with a negative voltage applied to gate. The power supply voltage is 8V, total current is 180mA. The LNA is biased at a Vgs of -0.4, Vds of 4V for first stage and Vds of 5V for second stage. The LNA is designed competitively for commercial product specification. The measured gain and noise figure of the completed amplifier was 20dB and 1dB, respectively. Also, input VSWR, P1dB and gain flatness was measured of 1.14 ~ l.3dB, 22.4dBm and $\pm$0.45dB, respectively. The designed LNA can be used for commercial product.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.2 s.93
• /
• pp.134-138
• /
• 2005

In this paper, we have developed a new type of the microwave phase conjugator for the active retrodirective antenna array. The circuit topology is consisted of a 2-port structure to avoid the complexity of LO and RF signal combination and matching, using the cascade connection of two single-ended mixers. The operating frequencies are 4.0 GHz, 2.01 GHz and 1.99 GHz for LO, RF, and IF, respectively. Conversion loss is measured to be -7 dB and 1-dB compression point 15 dBm with the LO power of 9 dBm. For the most important parameter, the isolation between RE leakage and IF signal is as high as 25 dB.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.11 s.102
• /
• pp.1086-1098
• /
• 2005

Two types of small wideband antennas are proposed for UWB application. One type is small biconical structure fed by coaxial probe, which is easy to be installed on the circuit board. The other type is of planar bow-tie type fed by coplanar transmission line. Generally, the bandwidth of the latter type is significantly narrower than that of the former type. It is shown, however that the bandwidth of the latter type can be made to be comparable to that of the former, if some series inductive component is introduced in the center conductor line in the CPW transmission line by replacing some part of center line with narrower line of higher characteristic impedance. The series inductance component play an important role of neutralizing the capacitive component of the small bow-tie antenna, thereby making broadband impedance matching possible. The small planar bow-tie antenna was fabricated and experimented. The experimental results for return loss are observed to be in good agreement with simulated results. The radiation pattern is also investigated experimentally.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.11
• /
• pp.1111-1116
• /
• 2011

In this paper, a 60 GHz bidirectional active phase shifter with 130 nm CMOS is presented by replacing CMOS passive switchs in switched-line type phase shifter with Common Gate Amplifier(bidirectional amplifier). Bidirectional active phase shifter is composed of bidirectional amplifier blocks and passive delay line network blocks. The suitable topology of bidirectional amplifier block is CGA(Common Gate Amplifier) topology and matching circuits of input and output are symmetrical due to design same characteristic of it's forward and reverse way. The direction(forward and reverse way) and amplitude of amplification can be controlled by only one bias voltage($V_{DS}$) using combination bias circuit. And passive delay line network blocks are composed of microstrip line. An 1-bit phase shifter is fabricated by Dongbu HiTek 1P8M 130-nm CMOS technology and simulation results present -3 dB average insertion loss and respectively 90 degree and 180 degree phase shift at 60 GHz.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.9
• /
• pp.816-825
• /
• 2007

With a view to building up a program used in conceptual design of liquid rocket engine system, a preliminary performance-based code for an integrated engine system has been developed by incorporating sub-modular programs for each essential engine component. Modular descriptions for each component were formulated mathematically with essential parameters. In the whole iterative circuits for predicting engine performance, matching conditions of mass flow rate and pressure drop through each engine component have been considered. Mass balance calculations at each inter-component boundary are found smoothly converged. All the pressure drops through engine components as a function of mass flow rate are added up to provide turbo-pump outlet condition. In this paper, the flow chart for each iterative circuit and design methodologies are presented. Resultant predictions are validated with real engine data.

• Journal of IKEEE
• /
• v.3 no.2 s.5
• /
• pp.221-225
• /
• 1999

In this paper, a new type of predistortion linearizer has been studied. It employs a series feedback amplifier with a large source inductance as a predistortion linearizer, which provides positive amplitude and negative phase deviations for input Power and can compensate for AM-AM and AM-PM distortions of power amplifier. This predistortion lineariaer consists of only one CaAs FET, large source inductor, input output matching networks and bias circuits. Because of its simple circuit, the linear can be operated over a broad bandwidth and has good thermal stability The characteristics of this linearizer can be easily tuned using source inductor, its gate bias condition. In fabricated linearizer, the third-order intermodulation distortion(IMD) for main amplifier alone is 10.61dBc, and the $IM_3$ for main amplifier with predistorter is 21.91dBc. Therefore, the $IM_3$ characteristic results an improvement of approximately 11dB.

• Korean Journal of Optics and Photonics
• /
• v.27 no.5
• /
• pp.165-173
• /
• 2016

In this paper, we propose a three-dimensional (3D) scanning system based on two line lasers. This system uses two line lasers with different wavelengths as light sources. 532-nm and 630-nm line lasers can compensate for missing scan data generated by geometrical occlusion. It also can classify two laser planes by using the red and green channels. For automatic registration of scanning data, we control a stepping motor and divide the motor's rotational degree of freedom into micro-steps. To this end, we design a control printed circuit board for the laser and stepping motor, and use an image processing board. To compute a 3D point cloud, we obtain 200 and 400 images with laser lines and segment lines on the images at different degrees of rotation. The segmented lines are thinned for one-to-one matching of an image pixel with a 3D point.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.15 no.2
• /
• pp.301-306
• /
• 2015

An ultra-compact and wideband low noise amplifier (LNA) in a quad flat non-leaded (QFN) package is presented. The LNA monolithic microwave integrated circuit (MMIC) is implemented in a $0.25{\mu}m$ GaN IC technology on a Silicon Carbide (SiC) substrate provided by Triquint. A source degeneration inductor and a gate inductor are used to obtain the noise and input matching simultaneously. The resistive feedback and inductor peaking techniques are employed to achieve a wideband characteristic. The LNA chip is mounted in the $3{\times}3-mm^2$ QFN package and measured. The supply voltages for the first and second stages are 14 V and 7 V, respectively, and the total current is 70 mA. The highest gain is 13.5 dB around the mid-band, and -3 dB frequencies are observed at 0.7 and 12 GHz. Input and output return losses ($S_{11}$ and $S_{22}$) of less than -10 dB measure from 1 to 12 GHz; there is an absolute bandwidth of 11 GHz and a fractional bandwidth of 169%. Across the bandwidth, the noise figures (NFs) are between 3 and 5 dB, while the output-referred third-order intercept points (OIP3s) are between 26 and 28 dBm. The overall chip size with all bonding pads is $1.1{\times}0.9mm^2$. To the best of our knowledge, this LNA shows the best figure-of-merit (FoM) compared with other published GaN LNAs with the same gate length.

• Journal of Advanced Navigation Technology
• /
• v.9 no.2
• /
• pp.103-109
• /
• 2005

This paper presents the design of a broadband hybrid mixer using dual-gate FET topology with a low-pass filter which improves return loss of output to isolate RF and LO signal. The low-pass filter shows the isolation with RF and LO signal of better than 40 dBc from 1.5 GHz to 5.5 GHz. The dual-gate mixer which has been designed by using cascade topology operates when the lower FET is biased in linear region and the upper FET is in saturation region. The input matching circuit has been designed to have conversion gain from 1.5 GHz to 5.5 GHz. The designed mixer with low-pass filter shows the conversion gain of better than 7 dB from 1.5 GHz to 5.5 GHz at the low LO power level of 0 dBm with the fixed IF frequency of 21.4 MHz.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.10
• /
• pp.820-826
• /
• 2013

In this paper, a compact and wideband CLAS(Conformal Load bearing Antenna Structure) was studied using smart skin technique. In order to satisfy the electrical performance of the CLAS antenna, the proposed CLAS antenna is composed of conductive mesh, face-sheet, radiator, honeycomb, housing. Especially, radiator is composed of composite magneto-dielectric material and radiating element etched on the PCB (Printed Circuit Board). The radiating element is inserted into the composite magneto-dielectric material and has sloted Folded LP(Log Periodic) structure. By fabricated composite magneto-dielectric, the resonance frequency is decreased and the impedance matching characteristics is improved. We verified that the antenna has wideband characteristics and compact size using the antenna test results.