• Transactions on Control, Automation and Systems Engineering
• /
• 제4권1호
• /
• pp.100-107
• /
• 2002

The advanced bilateral control algorithm, which can enlarge a reflected force by combining force reflection and compliance control, greatly enhances workability in teleoperation. In this scheme the maximum boundaries of a compliance controller and a force reflection gain guaranteeing stability and good task performance greatly depend upon characteristics of a slave arm, a master arm, and an environment. These characteristics, however, are generally unknown in teleoperation. It is, therefore, very difficult to determine such maximum boundary of the gain. The paper presented a novel method for design of an advanced bilateral controller. The factors affecting task performance and stability in the advanced bilateral controller were analyzed and a design guideline was presented. The neurofuzzy compliance model (NFCM)-based bilateral control proposed herein is an algorithm designed to automatically determine the suitable compliance for a given task or environment. The NFCM, composed of a fuzzy logic controller (FLC) and a rule-learning mechanism, is used as a compliance controller. The FLC generates compliant motions according to contact forces. The rule-learning mechanism, which is based upon the reinforcement learning algorithm, trains the rule-base of the FLC until the given task is done successfully. Since the scheme allows the use of large force reflection gain, it can assure good task performance. Moreover, the scheme does not require any priori knowledge on a slave arm dynamics, a slave arm controller and an environment, and thus, it can be easily applied to the control of any telerobot systems. Through a series of experiments effectiveness of the proposed algorithm has been verified.

• 동력기계공학회지
• /
• 제5권3호
• /
• pp.104-113
• /
• 2001

This paper describes a precise position synchronous control of two axes rotating system using BLDC motors and a cooperative control based on decoupling technique and PI control law. The system is required performances both good speed following and minimum position synchronous errors simultaneously. To accomplish these goals, the three kinds of controllers are designed. At first, the current and speed controller are designed very simply to compensate the influences of disturbances and to follow up speed references quickly. Especially, the two degree of freedom PI controller is used considering both good tracking for speed reference input and quick rejection of disturbances in speed controller. Finally, a position synchronous controller is designed as a simple proportional controller to minimize position synchronous errors. The validity of the proposed method is confirmed through some numerical simulations. Moreover, the results are compared to the conventional master-slave control ones to show the effectiveness of the proposed system.

• 대한치과보철학회지
• /
• 제35권4호
• /
• pp.662-673
• /
• 1997

The purpose of this study was to compare the accuracy between future impression and abutment impression using strain gauges. The master model used in this study was a partially edentulous mandibular metal cast with two fixture analogs on both sides. On the left, two future analogs were parallel, whereas right side, posterior future analog exhibiting a 15-degree lingual inclination. From master cast, 10 impressions were made for each of the three impression methods. The master frameworks was fabricated on the master model, and two-element strain gauge was attached to a master framework. The master framework was seated on each cast, and gold screws were tightened to 10 Ncm using a torque controller AI-1600 strain measurement system was used for strain measuring. Impression methods studied were : Group 1:abutment impression Group 2:fixture impression Group 3:combined impression (anterior:fixture impression, posterior:abutment impression) The results were as followed. 1. The strain values on X-axis and Y-axis according to the three impression methods showed no significant difference. 2. The strain values on parallel and angulated groups according to the three impression methods showed no significant difference. 3. The parallel group exhibited significantly higher accuracy in adaptation than angulated group for all experimental groups (p<0.05). In conclusion, it is considered that accuracy of implant prostheses is more affected by implant angulation than impression methods.

• Journal of Biosystems Engineering
• /
• 제29권2호
• /
• pp.159-166
• /
• 2004

In this study, we have developed a web-based management system for greenhouse teleoperation. The remote control system consisted of a database, a web-server, a controller in greenhouse, and clients. The database in the server stored user's information and greenhouse conditions was used to manage user's login and conditioning data. The management system developed by using Java applet, which was a client program for effective and easy management of greenhouse, monitored the greenhouse in real time. Master and driver boards were installed in the greenhouse control unit. Database on flowering to collect and analyze data exchanged data with the server. The master board could be managed effectively by timer routine, repeat control within setting time, and algorithm of setting points. Also, the greenhouse conditions could be controlled by manual or remote controller(PC) through a web browser in internet. Furthermore, all of the control devices of the greenhouse were managed by remote control of using PC and checked via camera installed in greenhouse. Finally, we showed the experimental results of the system which was installed in Pusan Horticultural Experiment Station.

• 전력전자학회논문지
• /
• 제16권1호
• /
• pp.50-57
• /
• 2011

본 논문에서는 마이컴(ATmega-2560) 기반의 디지털 통신 방식을 이용한 새로운 부하분담(Load-sharing) 알고리즘(Algorithm)을 제안한다. 기존의 아날로그 방식과 달리 고속 통신과 디지털 제어를 수행하고 실시간 제어를 위한 시분할 토큰버스 방식을 적용함으로서 효율적인 부하분담 및 리던던시(Redundancy)를 구현하였다. 또한 자동 ID 설정 알고리즘을 적용함으로서 시스템 비용을 낮추었으며, 제어기의 전압 및 전류 적분값을 공유하는 새로운 알고리즘으로 시스템의 속응성을 향상시켰다. 제작된 병렬 시스템은 각 모듈마다 독립된 제어기가 구성되어 있으며, 마스터(Master) 모듈의 지령치에 따라 슬레이브(Slave) 모듈이 부하분담을 수행한다. 본 논문에서는 PSIM을 통한 시뮬레이션과 시작품 제작을 통해 제안된 알고리즘의 타당성을 검증하였다.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• 제17권2호
• /
• pp.353-368
• /
• 2023

The four wing unmanned aerial vehicle owns the characteristics of small size, light weight, convenient operation and well stability. But it is easily disturbed by external environmental factors during flight with these disadvantages of short endurance and poor attitude solving ability. For solving these problems, a microprocessor based on STM32 chip is designed and the overall development is completed by the resources such as built-in timer and multi-function mode general-purpose input/output provided by the master micro controller unit, together with radio receiver, attitude meter, barometer, electronic speed control and other devices. The unmanned aerial vehicle can be remotely controlled and send radio waves to its corresponding receiver, control the analog level change of its corresponding channel pins. The master control chip can analyze and process the data to send multiple sets pulse signals of pulse width modulation to each electronic speed control. Then the electronic speed control will transform different pulse signals into different sizes of current value to drive the motor located in each direction of the frame to generate different rotational speed and generate lift force. To control the body of the unmanned aerial vehicle, so as to achieve the operator's requirements for attitude control, the PID controller based on Kalman filter is used to achieve quick response time and control accuracy. Test results show that the design is feasible.

• Journal of Mechanical Science and Technology
• /
• 제18권12호
• /
• pp.2080-2094
• /
• 2004

A model predictive controller is designed to control thermal power in a nuclear reactor. The basic concept of the model predictive control is to solve an optimization problem for finite future time steps at current time, to implement only the first optimal control input among the solved control inputs, and to repeat the procedure at each subsequent instant. A controller design model used for designing the model predictive controller is estimated every time step by applying a recursive parameter estimation algorithm. A 3-dimensional nuclear reactor analysis code, MASTER that was developed by Korea Atomic Energy Research Institute (KAERI), was used to verify the proposed controller for a nuclear reactor. It was known that the nuclear power controlled by the proposed controller well tracks the desired power level and the desired axial power distribution.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 1997년도 한국자동제어학술회의논문집; 한국전력공사 서울연수원; 17-18 Oct. 1997
• /
• pp.32-35
• /
• 1997

A recent development in the Flat Panel Display(FPD) industry requires an auto-alignment system which is operated in high speed and high precision. In the FPD production process, aligning photo-mask with respect to guide mark printed in the glass should be accomplished in the accuracy of sub-micron order. So the system has high bandwidth and needs a dedicated control system which is fast and robust enough to control linear motors in precise manner. Proposed auto-alignment system structure in this presentation which consists of the master controller board, the DSP position controller board which controls 3 axis precision linear motors, the servo system and the man machine interface software. Designed and tuned under repeated experiments, the proposed system showed a reasonable performance in the aspect of rise time and steady state error.

• 전기학회논문지
• /
• 제56권4호
• /
• pp.799-808
• /
• 2007

BACnet is an international standard communication protocol especially designed for building automation and control systems. BACnet uses the Master-Slave/Token-Passing (MS/TP) protocol as one of its field-level networks. A BACnet MS/TP field controller prototype and MS/TP network monitoring system are developed in this study. This report introduces the design and implementation methodology of a BACnet MS/TP field controller hardware, firmware and protocol stack. This report also presents the implementation methodology of BACnet MS/TP network monitoring system using VTS (Visual Test Shell). The methodologies introduced in this report will facilitate the develop and implementation of the BACnet-based control systems in building automation area.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2006년도 심포지엄 논문집 정보 및 제어부문
• /
• pp.195-197
• /
• 2006

In this paper, an interface unit is designed to efficiently monitor transmission data in Controller Area Network(CAN)-based control systems. The CAN uses a serial multi master communication protocol that efficiently supports distributed real-time control with a very high level of data integrity, and communication speeds of up to 1Mbps. The interface unit is composed of a DSP controller which collects data on the CAN bus and transfers data to a personal computer via serial communication to save and display of interesting signals. The experimental system consists of three DSP controllers which represent electronic control units of a vehicle, an interface unit for analysing the data on the bus, and a graphic monitoring program coded on the Windows platform. The validity and the effectiveness of the proposed simple type of CAN interface unit are shown through the experimental results.