• 전기전자학회논문지
• /
• 제17권2호
• /
• pp.189-201
• /
• 2013

본 논문은 연관된 합성기로부터 생성된 음성 경고음의 모델링에 관한 실험적 연구이다. 112명의 피실험자를 대상으로 심리적-육체적인 접근방법으로 4가지의 실험이 수행 되었다. 첫 번째 실험은 함성 경고음의 위급도를 지각하는 것을 모델링하여 6개의 음성-비음성 요소들을 구분하였다. 두 번째부터 네 번째의 실험은 위급도 지각의 주관적 변화와 객관적으로 계량화 할 수 있는 파라미터를 수치화 하였다. 이 논문은 응급성의 정도를 구분하는 것이 필요한 음성 합성 경고시스템의 설계에 적용될 수 있다.

• 대한조선학회지
• /
• 제12권2호
• /
• pp.3-12
• /
• 1975

As for two dimensional added mass coefficients for straight framed hull forms in a free surface of an ideal fluid, theoretical calculations by F.M. Lewis, vertical, K. Wendel, J.H. Hwang, and etc. are available; vertical modes of rectangular and triangle sections by Lewis, vertical, horizontal and torsional models of rectangular and triangle section by Wendel, and systematical calculations for vertical modes of single chine forms by Hwang. In this paper, employing the conformal transformation by which a unit circle and its exterior region can conformally mapped to a polygon and its exterior region, the author calculated two dimensional added inertia coefficients systematically for straight framed sections with single chine in horizontal and torsional modes of vibrations. As the results, it was found that sloping side angle is an important factor measuring the magnitude of two dimensional added inertia coefficient for a set of given values of the sectional area coefficient and the beam-draft ratio. To grasp it cleary in physical sense, pressure distributions are investigated for some typical section contours. The numerical results are presented graphically in the form of two dimensional added sectional area coefficients with beam-draft ratios and sloping side angles as parameters, so that the data may conveniently utilized for estimation of the added inertia coefficients based on a three parameter technique.

• 대한조선학회논문집
• /
• 제45권2호
• /
• pp.175-185
• /
• 2008

One of the concerns that arise during navigation in ice-covered waters is the magnitude of ice loads encountered by ships. However, the accurate estimation of ice loads still remains as a rather difficult task in the design of icebreaking vessels. This paper focuses on the development of simple ice load prediction formulas for the icebreaking cargo vessels. The maximum ice loads are expected from unbroken ice sheet and these loads are most likely to be concentrated at the bow area. Published ice load data for icebreaking vessels, from the model tests and also from full-scale sea trials, are collected and then several ice load prediction formulas are compared with these data. Finally, based on collected data, a semi-empirical ice load prediction formula is recommended for the icebreaking cargo vessels.

• Journal of Ecology and Environment
• /
• 제30권2호
• /
• pp.201-207
• /
• 2007

Researchers have used a variety of methods to measure patterns of animal movement, including the use of spatial data (mapping the position of a moving animal at specified intervals) and direct estimation of travel path length by pacing under a moving animal or group. I collected movement data from five groups of siamangs (Symphalangus syndactylus) using two different methods concurrently to estimate the effects of the method of data collection on estimates of daily path length (DPL). Estimates of DPL produced from spatial data collected at 15-minute intervals were 12% lower than estimates of DPL produced by pacing under the traveling animal. The actual magnitude of the difference was correlated with the travel distance, but there was no correlation between the proportional difference and the travel distance. While the collection of spatial data is generally preferable, as spatial data permit additional analyses of patterns of movements in two or three dimensions, the relatively small difference between the DPL's produced using different methods suggests that pacing is an acceptable substitute where the collection of spatial data is impractical. I also subsampled the spatial data at increasing time intervals to assess the effect of sampling interval on the calculation of daily path lengths. Longer sampling intervals produced significantly shorter estimates of travel paths than shorter sampling intervals. These results suggest that spatial data should be collected at short time intervals wherever possible, and that sampling intervals should not exceed 30 minutes. Researchers should be cautious when comparing data generated using different methods.

• Journal of electromagnetic engineering and science
• /
• 제15권1호
• /
• pp.53-58
• /
• 2015

For the testing of nonlinear power amplifiers, this paper suggests an approach to design optimized multisine signals that could be substituted for the original modulated signal. In the design of multisines, complex coefficients should be determined to mimic the target signal as much as possible, but very few methods have been adopted as general solutions to the coefficients. Furthermore, no solid method for the phase of coefficients has been proven to show the best resemblance to the original. Therefore, in order to determine the phase of multisine coefficients, a time-domain nonlinear optimization method is suggested. A frequency-domain-method based on the spectral response of the target signal is also suggested for the magnitude of the coefficients. For the verification, multisine signals are designed to emulate the LTE downlink signal of 10 MHz bandwidth and are used to test a nonlinear amplifier at 1.9 GHz. The suggested phase-optimized multisine had a lower normalized error by 0.163 dB when N = 100, and the measurement results showed that the suggested multisine achieved more accurate adjacent-channel leakage ratio (ACLR) estimation by as much as 12 dB compared to that of the conventional iterative method.

• KDI Journal of Economic Policy
• /
• 제36권2호
• /
• pp.1-64
• /
• 2014

본고는 소규모 개방경제를 상정한 동태확률모형을 통해 2000년 이후의 한국 거시경제의 변동요인들과 금융위기 기간의 통화정책과 재정정책의 변화요인을 추정하였다. 실증분석을 위해 동태확률모형은 경제성장률을 결정하는 두 가지 다른 추세요인과 다양한 구조충격요인 그리고 다양한 형태의 마찰을 포함시킴으로써, 거시변수들이 어떠한 요인에 의해 변화했는지를 정량적으로 분석하였다. 실증분석 결과, 금융위기 기간 동안 통화정책은 주로 테일러 준칙을 따른 것으로 나타난 반면, 재정정책의 반응은 재정준칙보다는 상대적으로 큰 폭의 재정충격요인에 의해서 설명된 것으로 추정되었다.

• Journal of Power Electronics
• /
• 제13권3호
• /
• pp.469-478
• /
• 2013

This paper proposes a novel scheme for the current controller for the grid-side converter (GSC) of permanent-magnet synchronous generator (PMSG) wind turbines to eliminate the high-order harmonics in the grid currents under grid voltage disturbances. The voltage unbalance and harmonics in three-phase systems cause grid current distortions. In order to mitigate the input current distortions, multi-loop current controllers are applied, where the positive-sequence component is regulated by proportional-integral (PI) controllers, and the negative-sequence and high-order harmonic components are regulated by proportional-resonance (PR) controllers. For extracting the positive/negative-sequence and harmonic components of the grid voltages and currents without a phase delay or magnitude reduction, composite observers are applied, which give faster and more precise estimation results. In addition, an active damping method using PR controllers to damp the grid current component of the resonant frequency is employed to improve the operating stability of VSCs with inductor-capacitor-inductor (LCL) filters. The validity of the proposed method is verified by simulation and experimental results.

• International Journal of Automotive Technology
• /
• 제6권2호
• /
• pp.171-181
• /
• 2005

The purpose of this paper is two-fold: 1) A novel algorithm in order to extract lane-related information from road images is presented; 2) Design specifications of an image processing onboard unit capable of extracting lane­related information in real-time is also presented. Obtaining precise information from road images requires many features due to the effects of noise that eventually leads to long processing time. By exploiting a FPGA and DSP, we solve the problem of real-time processing. Due to the fact that image processing of road images relies largely on edge features, the FPGA is adopted in the hardware design. The schematic configuration of the FPGA is optimized in order to perform 3 $\times$ 3 Sobel edge extraction. The DSP carries out high-level image processing of recognition, decision, estimation, etc. The proposed algorithm uses edge features to define an Edge Distribution Function (EDF), which is a histogram of edge magnitude with respect to the edge orientation angle. The EDF enables the edge-related information and lane-related to be connected. The performance of the proposed system is verified through the extraction of lane-related information. The experimental results show the robustness of the proposed algorithm and a processing speed of more than 25 frames per second, which is considered quite successful.

• 한국자동차공학회논문집
• /
• 제13권4호
• /
• pp.58-65
• /
• 2005

A method measuring angular speed and estimating angular acceleration of an automotive wind shield wiper pivot with limited resources has been proposed. Limited resources refer to the fact that processes cannot be operated in real-time with a regular notebook running a Microsoft Windows. Also, they refer to the fact that data acquisition cards have only two general purpose counters as many generic cards do. An optical incremental encoder has been employed for measuring angular motion. To measure the angular speed of the pivot, periods for the encoder's output pulses have been measured as the speed is related to the reciprocal of the period. Since only information acquired from one counter channel is the magnitude of the angular speed, sign correction is necessary. Also the information for the exact time when a pivot passes left and right dead points is also missing and the situation is inherent to the hardware setup. To find out the zero-crossing time of the angular speed, a linear interpolation technique has been employed. Lastly, to overcome the imperfection of the mechanical encoders, the angular speed has been curve fitted to a spline. Angular acceleration can be obtained by a differentiation of the angular speed.

• 한국자동차공학회논문집
• /
• 제12권1호
• /
• pp.106-113
• /
• 2004

Most of mechanical structures are composed of many substructures connected to one another by various types of mechanical joints. In automotive engineering, it is important to study these connected structures under various dynamic forces for the evaluations of fatigue life and stress concentration exactly. In this study, the dynamic response of vehicle structure to external forces is classified an inverse problem involving strains from the experiment and the analysis. The practical dynamic forces are determined by the combination of the analytical and experimental method with analyzed strain by quasi-static finite element analysis under unit force and with measured strain by a strain gage under driving load, respectively. In a stressed body, inter-molecular chemical bonds are failed beyond the certain magnitude. The failure of molecular structure in material is considered as a time process of which rate is determined by mechanical stress. That is, the failure of inter-molecular chemical bonds is the fatigue lift of material. This kinetic concept is expressed as lethargy coefficient. And S-N curve is obtained with the lethargy coefficient from quasi-static tensile test. Equivalent practical dynamic force is obtained from the identification of practical dynamic force for one loading point. Using the practical dynamic force and S-N curve, fatigue life of a window pillar is analyzed with FEM under the identified force by the procedure of above mentioned.