• Journal of the Korean Magnetics Society
• /
• v.8 no.5
• /
• pp.282-287
• /
• 1998

Dependence of magnetoresistance on base pressure and deposition rates of each Fe, Co, Cu layers in the $Fe(50{\AA}/[Co(17{\AA})/Cu(24{\AA})]_20$ multilayer thin films, prepared by dc magnetron sputtering on Corning glass, were investigated. AFM analysis, X-ray diffraction analysis, vibrating sample magnetometer analysis, and magnetoresustance measurement (4-probe method) were performed. The multilayer films deposited under low base pressure increases magnetoresistance ratio by preventing oxidation. Annealing for the samples at a moderate temperature allowed larger textured grain with no loss in the periodicity. Magnetoresistance ratio of the annealed multilayers was increased due to the increase antiferromagnetically coupled fraction of the film after annealing. Optimization of deposition rate was greater than 1 $\AA$/s for Fe, and 2.8 $\AA$/s for Cu. Deposition rate of Co showed a tendency of increasing of magnetoresistance ratio due to the formation of flat magnetic layer in case of high deposition rate of Co.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.188.1-188.1
• /
• 2015

For present investigation Fe/MgO/Fe/Co multilayer stack is grown on Si substrate using e-beam evaporation in ultrahigh vacuum. This stack is irradiated perpendicularly by 120 MeV $Ag^{8+}$ at different fluences ranging from $1{\times}10^{11}$ to $1{\times}10^{13}ions/cm^2$ in high vacuum using 15UD Pelletron Accelerator at Inter University Accelerator Centre, New Delhi. Magnetic measurements carried out on pre and post irradiated stacks show significant changes in the shape of perpendicular hysteresis which is relevant with previous observation of re-orientation of magnetic moment along the direction of ion trajectory. However increase in plane squareness may be due to the modification of interface structure of stacks. X-ray reflectivity measurements show onset of interface roughness and interface mixing. X-ray diffraction measurements carried out using synchrotron radiation shows amorphous nature of MgO and Co layer in the stack. Peak corresponding body centered Fe [JCPDS-06-0696] is observed in X-ray diffraction pattern of pre and post irradiated stacks. Peak broadening shows granular nature of Fe layer. Estimated crystallite size is $22{\pm}1nm$ for pre-irradiated stack. Crystallite size first increases with irradiation then decreases. Structural quality of these stacks was further studied using transmission electron microscopic measurements. Thickness from these measurements are 54, 36, 23, 58 and 3 nm respectively for MgO, Fe, MgO, Fe+Co and Au layers in the stack. These measurements envisage poor crystallinity of different layers. Interfaces are not clear which indicate mixing at interface. With increase fluence mixing and diffusion was increased in the stack. X-ray absorption spectroscopic measurements carried out on these stacks show changes of Fe valence state after irradiation along with change of O(2p)-metal (3d) hybridized state. Valence state change predicts oxide formation at interface which causes enhanced in-plane magnetization.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.29-29
• /
• 2009

현재 고집적 비휘발성 메모리 소자로는 MRAM (Magnetic Random Access Memory)과 PRAM (Phase Magnetic Random Access Memory)이 활발하게 미국과 일본, 한국 등에서 다양한 연구가 진행되어 오고 있다. 이 중에서 MRAM은 DRAM과 비슷한 10 ns의 빠른 읽기/쓰기 속도와 비휘발성 특성을 가지고 있으며, 전하를 저장할 커패시터가 필요 없고, 두 개의 자성충에 약 10 mA 정도의 전류를 가하면 그때 발생하는 약 10 Oe의 자장을 개개의 비트를 write하고, read 시에는 각 비트의 자기저항을 측정함으로써 데이터를 저장하고 읽을 있으므로, 고집적화가 가능성하다 [1]. 현재 우수한 박막 재료가 개발 되었으나, 고집적 MRAM 소자의 양산에는 해결 하여야 하는 문제점이 있다. 특히 다층 박막으로 구성되어 있으므로 식각 공정의 개발이 필수적이다. 지금까지 MRAM 재료의 식각은 주로 Ion milling, ICP, ECR등의 플라즈마 장치를 되었고, 식각 가스로는 할로겐 기체와 금속카보닐 형성을 위한 Co/$NH_3$와 $Ch_3OH$ 기체가 이용되고 있다. 그러나 할로겐 계열의 기체를 사용할 경우, 식각 부산물들의 높은 끓는점 때문에 식각 부산물이 박막의 표면에서 열적 탈착에 의하여 제거되지 않기 때문에 높은 에너지를 가지는 이온의 도움에 의한 식각이 필요하다. 또한 Cl 계열의 기체를 사용할 경우, 식각 공정 후, 시료가 대기에 노출되면 대기 중의 수분과 식각 부산물이 결합하여 부식 현상이 발생하게 된다. 그러므로 이를 방지하기 위한 추가 공정이 요구된다. 최근에는 부식 현상이 없고, MTJ 상부에 사용되는 Ta 또는 Ti Hard mask와의 높은 선택비를 가지는 $CH_3OH$ 또는 CO/$NH_3$가 사용되고 있다. 하부 박막에 따른 식각 특성에 연구와 다층의 박막의 식각 공정에 발생에 관한 발표는 거의 없다. MRAM을 양산에 적용하기 위하여서는 Main etch 공정에서 빠른 식각 공정이 필요하고, Over etch 공정에서 하부박막에 대한 높은 선택비가 요구된다. 그러므로 본 논문에서는 식각 변수에 따른 플라즈마 측정과 표면 반응을 비교하여 각 공정의 식각 메커니즘을 규명하고, Main Etch 공정에서는 $Cl_2$/Ar 또는 $BCl_3$/Ar 가스를 이용하여 식각 실험을 수행하고, Over etch 공정에는 낮은 Ta 박막 식각 속도를 가지는 $Ch_4/O_2$/Ar 또는 $Ch_3OH$/Ar 가스를 이용하고자 한다. 플라즈마 내의 식각종과 Ta 박막과의 반응을 XPS와 AES를 이용하여 분석하고, 식각 공정 변수에 따른 식각 속도, 식각 선택비와 식각 프로파일 변화를 SEM을 이용하여 관찰한다.

• Korean Chemical Engineering Research
• /
• v.43 no.1
• /
• pp.85-91
• /
• 2005

$SnO_2$ films were prepared at room temperature under a $(CH_3)_4Sn-H_2-O_2$ atmosphere in order to obtain transparent conductive polymer by using ECR-MOCVD (Electron Cyclotron resonance -Metal Organic Chemical Vapor Deposition) system. The electrical properties of the films were investigated as function of process parameters such as deposition time, microwave power, magnetic current power, magnet/showering/substrate distance and working pressure. An increase in microwave power and magnetic current power brought on $SnO_2$ film formation with low electric resistivity. On the other hand, the effects of process parameters described above on optical properties were insignificant in the range of our experimental scope. The transmittance and reflectance of the films prepared by the ECR-MOCVD exhibited their average values of 93-98% at wave length range of 380-780 nm and 0.1-0.5%, respectively. The grain size of the $SnO_2$ films that are also insensitive with the process parameters were in the range of 20-50 nm. On the basis of experimental data obtained in the present study, electrical resistivity of $7.5{\times}10^{-3}ohm{\cdot}cm$, transmittance of 93%, and reflectance of 0.2% can be taken as optimum values.

• Journal of Korea Multimedia Society
• /
• v.14 no.3
• /
• pp.414-422
• /
• 2011

The paper is for top and bottom symmetrical phase controlled loop antenna using for multi-media devices. We developed a top and bottom phase control loop pattern arrangement methods for loop antenna in mobile devices like as a cell phone and PCS, WCDMA. In the loop antenna pattern, arrange close adhesive the loop antenna pattern $180^{\circ}$ cycle in wave length, the radiated electro-magnetic wave from close adhesive loop pattern in $180^{\circ}$ become to coherent wave than the phase controlled loop antenna has high efficiency and high radiation gain. To acquire a wide band width on phase controlled loop antenna, we arrange a top and bottom symmetrical architecture loop pattern that bas a $180^{\circ}$ wave length in each layer. Top and bottom each layer bas a U form pattern separated $90^{\circ}$ wave length each other. This architecture cause a well balanced electro-magnetic flow control that acquired wide bandwidth resonance response in loop pattern antenna. In experiment, we designed a WCDMA mobile multi-media antenna in $40mm{\times}6mm$ area thickness 0.2mm, in that passive experiment the radiation efficiency is over 50% and over 0dBi radiation average gain was acquired, in the active experiment in real multi-media device we acquired -4dBi average gain and 43% transmit/receive efficiency.

• Journal of the Korean Ceramic Society
• /
• v.42 no.3 s.274
• /
• pp.211-217
• /
• 2005

[ $Zn_{1-x}Co_{x}O$ (x=0-0.3) films were grown on Corning 7059 glasses by asymmetrical bipolar pulsed dc magnetron sputtering. The c-axis orientation along (002) plane was enhanced with increasing Co concentration. The $Zn_{1-x}Co_{x}O$ films are grown with fibrous grains of tight dome shape. The transmittance spectra measured from UV-visible showed that sp-d exchange interactions and typical d-d transitions become activated with increasing Co concentration. The electrical resistivity of $Zn_{1-x}Co_{x}O$ films increased with increasing Co concentration, especially it increased greatly at $30at\% Co. X-ray photoelectron spectroscopy and alternating gradient magnetometer analyses indicated that no Co metal cluster is formed and the ferromagnetic properties are exhibited. The low electrical resistivity and room temperature ferromagnetism of $Zn_{1-x}Co_{x}O$ thin films suggested the possibility of the application to Diluted Magnetic Semiconductors (DMSs).

• Journal of the Korean Magnetics Society
• /
• v.8 no.6
• /
• pp.380-387
• /
• 1998

In this paper, a sensor material with Fe/Zr multilayer thin film, in which the change in the magnetization and strain with hydrogenation is maximized, were developed. Compositionally modulated (CM) Fe/Zr multilayers with a $Fe_{80}Zr_{20}$ composition and modulation wavelengths ($\lambda$) $3~50{\AA}$ were deposited by sequentially sputtering (RF diode) elemental Fe and Zr targets. The films were electrolytically hydrogenated to select the optimum Fe/Zr multilayers that show the maximum increases in the magnetization and strain with hydrogenation. The changes in the magnetic properties of the thin films after hydrogenation, were measured using a hysteresis graph and a vibrating sample magnetometer (VSM), and the strains induced in the films by hydrogenation were also measured using a laser heterodyne interferometer (LHI). The optimum sensor material selected was incorporated in a fiber-optic hydrogen sensor (that can sense indirectly amount of hydrogen injected) by depositing it directly on the sensing arm of a single-mode fiber Michelson interferometer. The developed sensor holds significant promise for non-destructive test evaluation (NDE) applications because it is expected to be useful for detecting easily and accurately the subsurface corrosion in structural systems.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2009.05a
• /
• pp.111-112
• /
• 2009

Diamond-like carbon (DLC) is a convenient term to indicate the compositions of the various forms of amorphous carbon (a-C), tetrahedral amorphous carbon (ta-C), hydrogenated amorphous carbon and tetrahedral amorphous carbon (a-C:H and ta-C:H). The a-C film with disordered graphitic ordering, such as soot, chars, glassy carbon, and evaporated a-C, is shown in the lower left hand corner. If the fraction of sp3 bonding reaches a high degree, such an a-C is denoted as tetrahedral amorphous carbon (ta-C), in order to distinguish it from sp2 a-C [2]. Two hydrocarbon polymers, that is, polyethylene (CH2)n and polyacetylene (CH)n, define the limits of the triangle in the right hand corner beyond which interconnecting C-C networks do not form, and only strait-chain molecules are formed. The DLC films, i.e. a-C, ta-C, a-C:H and ta-C:H, have some extreme properties similar to diamond, such as hardness, elastic modulus and chemical inertness. These films are great advantages for many applications. One of the most important applications of the carbon-based films is the coating for magnetic hard disk recording. The second successful application is wear protective and antireflective films for IR windows. The third application is wear protection of bearings and sliding friction parts. The fourth is precision gages for the automotive industry. Recently, exciting ongoing study [1] tries to deposit a carbon-based protective film on engine parts (e.g. engine cylinders and pistons) taking into account not only low friction and wear, but also self lubricating properties. Reduction of the oil consumption is expected. Currently, for an additional application field, the carbon-based films are extensively studied as excellent candidates for biocompatible films on biomedical implants. The carbon-based films consist of carbon, hydrogen and nitrogen, which are biologically harmless as well as the main elements of human body. Some in vitro and limited in vivo studies on the biological effects of carbon-based films have been studied [$2{\sim}5$].The carbon-based films have great potentials in many fields. However, a few technological issues for carbon-based film are still needed to be studied to improve the applicability. Aisenberg and Chabot [3] firstly prepared an amorphous carbon film on substrates remained at room temperature using a beam of carbon ions produced using argon plasma. Spencer et al. [4] had subsequently developed this field. Many deposition techniques for DLC films have been developed to increase the fraction of sp3 bonding in the films. The a-C films have been prepared by a variety of deposition methods such as ion plating, DC or RF sputtering, RF or DC plasma enhanced chemical vapor deposition (PECVD), electron cyclotron resonance chemical vapor deposition (ECR-CVD), ion implantation, ablation, pulsed laser deposition and cathodic arc deposition, from a variety of carbon target or gaseous sources materials [5]. Sputtering is the most common deposition method for a-C film. Deposited films by these plasma methods, such as plasma enhanced chemical vapor deposition (PECVD) [6], are ranged into the interior of the triangle. Application fields of DLC films investigated from papers. Many papers purposed to apply for tribology due to the carbon-based films of low friction and wear resistance. Figure 1 shows the percentage of DLC research interest for application field. The biggest portion is tribology field. It is occupied 57%. Second, biomedical field hold 14%. Nowadays, biomedical field is took notice in many countries and significantly increased the research papers. DLC films actually applied to many industries in 2005 as shown figure 2. The most applied fields are mold and machinery industries. It took over 50%. The automobile industry is more and more increase application parts. In the near future, automobile industry is expected a big market for DLC coating. Figure 1 Research interests of carbon-based filmsFigure 2 Demand ratio of DLC coating for industry in 2005. In this presentation, I will introduce a trend of carbon-based coating research and applications.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.3
• /
• pp.139-145
• /
• 2005

[ $SnO_x$ ] films on the flexible substrate of PET film were prepared at ambient temperature under a $(CH_3)_4Sn(TMT: tetra-methyl tin)-H_2-O_2$ atmosphere in order to obtain transparent conductive polymer by using ECR-MOCVD(Electro Cyclotron Resonance Metal Organic Chemical Yfpor Deposition) system. The prepared $SnO_x$ thin films show generally over $90\%$ of optical transmittance at wavelength range of 380-780nm and about $1\times10^{-2\~3}ohm{\cdot}cm$ of electrical resistivity. In the present study, effects of $O_2/TMT\;and\;H_2/TMT$ mole ratio on the properties of $SnO_x$ films are investigated and the other process parameters such as microwave power, magnetic current power, substrate distance and working pressure are fixed. Based on our experimental results, the $SnO_x$ film composition ratio of Sn and O directly influences on the electrical and optical properties of the films prepared. The $SnO_x$ film with low electric resistivity and high transmittance could be obtained by controlling the process parameters such as $O_2/TMT\;and\;H_2/TMT$ mole ratio, which play an important role to change the composition ratio between Sn and O. An increase of $O_2/TMT$ mole ratio brought on the increases 0 content in the $SnO_x$ film. On the other hand, an increase of $H_2/TMT$ mole ratio lead to decreases the oxygen content in the film. The optimized composition ratio of oxygen : tin Is determined as 2.4: 1 at $O_2/TMT$ of 80 and $H_2/TMT$ of 40 mole ratio, respectively.

• Journal of the Korean Magnetics Society
• /
• v.18 no.5
• /
• pp.195-199
• /
• 2008

Composites of $Fe_{93.5}Si_{6.5}$ powder and epoxy were prepared using a thermal curing process. Scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and network analyzer were used to analyze the structure, electromagnetic properties and microwave absorption of the composites. Results show that the saturation magnetization depends on the fraction of the $Fe_{93.5}Si_{6.5}$ powder in the composite, which affects initial permeability. It is believed that the eddy current loss is a dominant factor over 1 GHz and that the resonance frequency of the composite decreases with increasing fractions of $Fe_{93.5}Si_{6.5}$ powder. Finally, reflection loss was calculated from the permeability and permittivity of these composites. Composite with 50 wt.% $Fe_{93.5}Si_{6.5}$ powder fractions and 5 mm thickness showed reflection loss below -20 dB from 3.66 GHz to 4.16 GHz. Therefore, it is believed that thin Fe-Si/epoxy composites may be a good candidate for microwave absorption application.