• Title/Summary/Keyword: magnesium water

Search Result 433, Processing Time 0.026 seconds

Stability of High Internal Phase Emulsions

  • Park, C-I.;W-G. Cho
    • Proceedings of the SCSK Conference
    • /
    • 1999.10a
    • /
    • pp.65-74
    • /
    • 1999
  • We have studied the stability of W/O high internal phase emulsions(HIPE) containing water, cetyl dimethicone copolyol and oils varying magnesium sulfate in the range 0 to 0.5wt% and oil polarities, respectively. The rheological consistency was mainly destroyed by the coalescence of the deformed water droplets. The greater the increase of concentrated modulus was, the less coalescence occurred and the more consistent the concentrated emulsions were. The increasing pattern of complex modulus versus volume fraction has been explained with the resistance to coalescence of the deformed interfacial film of water droplets in concentrated W/O emulsion. The stability is dependent on: (i) the choice of the oil is important, the requirements coincide with the requirements for the formation of the rigid liquid crystalline phases :5; and (ii) addition of salts the aqueous phase opposes the instability due to coalescence:. Increasing the salt concentration increases the refractive index of the aqueous phase. It lowers the difference in the refractive index between the oil and aqueous phases. This decreases the attraction between the water domains, thus increasing the stability.

  • PDF

Enhancing the Thermotolerance of Entomopathogenic Isaria fumosorosea SFP-198 Conidial Powder by Controlling the Moisture Content Using Drying and Adjuvants

  • Kim, Jae Su;Lee, Se Jin;Lee, Hyang Burm
    • Mycobiology
    • /
    • v.42 no.1
    • /
    • pp.59-65
    • /
    • 2014
  • Entomopathogenic fungi are promising pest-control agents but their industrial applicability is limited by their thermosusceptibility. With an aim to increase the thermotolerance of Isaria fumosorosea SFP-198, moisture absorbents were added to dried conidial powder, and the relationship between its water potential and thermotolerance was investigated. Mycotized rice grains were dried at $10^{\circ}C$, $20^{\circ}C$, $30^{\circ}C$, and $40^{\circ}C$ and the drying effect of each temperature for 24, 48, 96, and 140 hr was determined. Drying for 48 hr at $10^{\circ}C$ and $20^{\circ}C$ reduced the moisture content to < 5% without any significant loss of conidial thermotolerance, but drying at $30^{\circ}C$ and $40^{\circ}C$ reduced both moisture content and conidial thermotolerance. To maintain thermotolerance during storage, moisture absorbents, such as calcium chloride, silica gel, magnesium sulfate, white carbon, and sodium sulfate were individually added to previously dried-conidial powder at 10% (w/w). These mixtures was then stored at room temperature for 30 days and subjected to $50^{\circ}C$ for 2 hr. The white carbon mixture had the highest conidial thermotolerance, followed by silica gel, magnesium sulfate, and then the other absorbents. A significant correlation between the water potential and conidial thermotolerance was observed in all conidia-absorbent mixtures tested in this study (r = -0.945). Conidial thermotolerance in wet conditions was evaluated by adding moisturized white carbon (0~20% $H_2O$) to conidia to mimic wet conditions. Notably, the conidia still maintained their thermotolerance under these conditions. Thus, it is evident that conidial thermotolerance can be maintained by drying mycotized rice grains at low temperatures and adding a moisture absorbent, such as white carbon.

Single- and repeated-dose oral toxicity tests of deep sea water mineral extracts in ICR mice

  • Hwang, Min Hee;Cho, Miju;Lee, Dong Gun;Go, Eun Byeol;Park, Young Sig;Chung, Namhyun
    • Journal of Applied Biological Chemistry
    • /
    • v.59 no.3
    • /
    • pp.227-231
    • /
    • 2016
  • Deep sea water (DSW) is located 100 to 500 m below the sea surface. DSW is widely used in various fields, and is an important source of minerals that can be used to treat mineral deficiency. In the present study, the oral toxicity of DSW-mineral extracts was determined using single-dose and 14-day repeated dose oral toxicity tests in ICR mice. For the single-dose oral toxicity tests, mineral extracts of magnesium (Mg) and calcium (Ca) at doses of 0, 6, 270, 810, and 1,350 mg/kg, respectively, were orally administered to mice once at the beginning of the experiment, and the mice were observed for 14 days. For the 14-day repeated dose oral toxicity tests, Mg and Ca mineral extracts at doses of 0, 3, 135, 405, 675 mg/kg, respectively, were orally administered to mice daily, and the mice were observed for 14 days. Various tests were performed including visual observation; analysis of relative organ weight, food intake, and organ weight; biochemical analysis, and histopathology. The results indicated that mortality and changes in appearance were not observed among differentially administered groups of male and female ICR mice during the experimental period. Differences in body weight gain, food intake, organ weight, and histopathology parameters were not significant between the control and mineral-administered groups. Some results of the biochemical analyses were significantly different, but showed no specific tendencies. Overall, no evidence of toxicity was observed from the oral administration of DSW extracts of Ca and Mg in ICR mice.

Dynamics of Nutrient and KDICical Constituents during Litter Decomposition (낙엽의 분해과정에 따른 영양염류 및 화학적 구성원의 동태)

  • Mun, hyeibg-Tae;Jae-Hoon Pyo
    • The Korean Journal of Ecology
    • /
    • v.17 no.4
    • /
    • pp.501-511
    • /
    • 1994
  • Dynamics of nutrients, non-polar, water solubles, acid solubles and acid insolubles (lignin) in decomposing litter were investigated for 2 years in the oak, Quercus acutissima, and the pitch pine, Pinus rigida, stands in the vicinity of Kongju, Chungnam Province. Nitrogen and phosphorus conetrations in decomposing litter increased with time elapsed, however, potassium decreased rapidly within three months and then remined constant with time elapsed. Calcium concentration in needle litter during experimental period was lower than that of initial concentration in needle litter during experimental period was lower than that of initial concentration, and showed no significant variation with time elapsed. Calcium concentration in oak litter during the experimental period, however, were higher than that of initial concentration. Magnesium concentration in oak litter decreased repidly during six months, and then remaines constant thereafter. Annual amount of nitrogen, phosphorus, potassium, calcium and magnesium which returned to soil via litter decomposition in the oak and the pitch pine stands was $3.3g/m^2$ and $0.9g/m^2$ for N, $0.03g/m^2$ and $0.01g/m^2$ for P, $1.3g/m^2$ and $0.7g/m^2$ for K, $0.7g/m^2$ and $1.2g/m^2$ for Ca, $0.9g/m^2$ and $0.4g/m^2$ for Mg, respectively. Non-polar, and water- and acid-soluble fractions in decomposing litter decreased and lignin increased with time.

  • PDF

Feasibility Tests on Struvite Production from Liquid Fertilizer by Utilizing Ferronickel Slag and Sewage Sludge Ash (페로니켈슬래그와 하수슬러지소각재를 이용한 액비로부터 스트루바이트 생산 타당성 연구)

  • Kim, Hyeon;Kwon, Gyutae;Jahng, Deokjin
    • Journal of Korean Society on Water Environment
    • /
    • v.34 no.3
    • /
    • pp.316-327
    • /
    • 2018
  • Liquid fertilizers made from livestock manure contain high concentrations of nitrogen and phosphorus and thus are used as a fertilizer. However, excessive use of liquid fertilizer causes eutrophication of agricultural land and nonpoint source pollution. In this study, as a means of lowering the nutrient concentrations, struvite ($MgNH_4PO_4{\cdot}6H_2O$) production from the liquid fertilizer was investigated. When liquid fertilizers produced in Gyeonggido were analyzed, its characteristics differed by region and season, but the phosphorus concentration was commonly lower than that of nitrogen. When $K_2HPO_4$ and $MgCl_2$ were added to the liquid fertilizers, the optimal pH for struvite formation was pH 9.5. For environmentally friendly sources of magnesium and phosphate, ferronickel slag (FNS) and sewage sludge ash (SSA) were suspended in deionized water and extracted by sulfuric acid with various mass ratios. The optimum conditions for extracting FNS and SSA were 4.0 M sulfuric acid and 0.35 mass ratio of sulfuric acid to sewage sludge ash, respectively. For forming struvite, 0.233 L of SSA leachate (SSAL) was added into 0.3 L of liquid fertilizer containing 2,586 mg/L of ammonia and 110 mg/L of phosphate, pH was then adjusted to pH 9.5 using 10 M of NaOH. Afterwards 0.333 L of FNS leachate (FNSL) was added to this mixed solution. After a reaction for 1 hr at room temperature, the remaining concentrations of magnesium, ammonium, and phosphate were less than 50 mg/L, 500 mg/L and 150 mg/L, respectively, and 30 g of precipitates were obtained, most of which were struvite.

A Hardening and Strength Properties of Magnesium Phosphate Mortars for Rapid Repair Materials (급속 보수용 마그네슘 인산염 모르타르의 경화 및 강도특성)

  • Oh, Hongseob;Lee, Inhee
    • Journal of the Korea institute for structural maintenance and inspection
    • /
    • v.23 no.3
    • /
    • pp.103-110
    • /
    • 2019
  • Damage to the pavement system due to various causes will be required rapid repair work for reopening the vehicle traffic. The magnesium oxide phosphate composite(MPC) has a short curing time and is capable of early compressive strength development, is suitable for rapid repair materials. The aim of this study was to evaluate the hardening and compressive strength characteristics of MPC according to the water-binder (W / B) ratio and magnesium-phosphate(M / P) ratio in order to develop repair materials consisted with light burned magnesia and potassium dihydrogen phosphate. In order to ensure the workability in the field application, the difference of mechanical properties according to standard sand and ordinary sand and performance of retards were evaluated. The mix proportion with W/B ratio was about 35% and the M/P ratio was about 1.0 ~ 1.2 has a superior perfomance with strength and hardening condition. Especially, the strength of composite at only 1 day curing with W/B ratio of 0.35 and the M/P ratio of 1.2 was shown the higher than 25.0 MPa. Boric acid as a retarder was found to be suitable for ensuring the working time, and the purity of magnesium oxide was about 90 ~ 95%, which is effective for ensuring curing time and strength.

A Comparative Study on the Use of Seawater and Sea Salt in Nutrient Elimination (영양염제거에서 해수 및 해수염에 관한 비교연구)

  • Cainglet, Annaliza Pabrua;Kim, Woo-Hang
    • Journal of the Korean Society of Marine Environment & Safety
    • /
    • v.22 no.7
    • /
    • pp.829-835
    • /
    • 2016
  • An excess in the nutrients such as nitrogen and phosphate leads to a phenomenon called eutrophication. In order to avoid this, numerous methods have been used to remove excess nutrients in the water. In this study, the use of a chemical method was assessed through the formation of magnesium ammonium phosphate. The difference in the removal efficiency of seawater and sea salt solution as primary sources of $Mg^{2+}$ ions and $Ca^{2+}$ ions for the formation of magnesium ammonium phosphate (MAP) and hydroxyapatite (HAP) respectively, were observed, taking into account the changes in pH and concentration. The results showed that seawater removed about 90 % phosphate and less than 50 % ammonia in sewage water condition, whereas the sea salt solution removed almost 90 % phosphate and 70 % ammonia in solution at pH 9 and 10 mM concentration of sea salt which further increases as the optimum ${Mg/PO_4}^{3-}$, ${NH_4}^+$ ratio reaches 2. The difference in the removal efficiency of seawater and sea salt was due to the fact that the set-ups were prepared in different conditions. This study suggests that both seawater and sea salt can be used to remove nutrients from the water. The relatively higher removal of phosphate can be explained by the formation of HAP from free $Ca^{2+}$ ions initially present in seawater and sea salt solution.

Impact of urbanization on Nwaorie and Otamiri Rivers in Owerri, Imo State, Nigeria

  • Ogbomida, Emmanuel T.;Emeribe, Chukwudi N.
    • Advances in environmental research
    • /
    • v.2 no.2
    • /
    • pp.119-129
    • /
    • 2013
  • The study examined the effect of urbanization on the water quality of Nwaorie and Otamiri Rivers in Owerri metropolis, Imo State, South-East Nigeria. Water samples were collected from Nwaorie and Otamiri Rivers from four sampling stations up and down stream. Water parameters analyzed using standard procedures were: color, turbidity, temperature, pH, total hardness, total solids, metals (Iron and magnesium), anions (nitrate and ammonia) and Fecal coliform. Results showed increased levels of coloration, iron, ammonia, turbidity and fecal coliform which exceeded the World Health Organization (WHO) permissible limits for drinking water. Increase in these parameters indicated influx of industrial effluent from the nearby industries and indiscriminate disposal of wastes at the bank of the rivers. Application of ANOVA showed various degree of variation in pollutants levels between the two rivers and at different sampling points. River Nwaorie was observed to be more impacted than River Otamiri. High values of iron observed from the study could be deleterious to human health if the river water is consumed without treatment. The study, therefore, recommended proper waste management and disposal as well as effluent treatments in Owerri municipal against pollution of surface water.

Performance Degradation of Mea with Cation Contamination in Polymer Electrolyte Membrane Water Electrolysis (고분자 전해질막 수전해 막전극접합체의 양이온 오염에 따른 성능 저하)

  • JUNG, HYEYOUNG;CHOI, NAKHEON;IM, SUHYUN;YOON, DAEJIN;MOON, SANGBONG
    • Journal of Hydrogen and New Energy
    • /
    • v.28 no.4
    • /
    • pp.331-337
    • /
    • 2017
  • Proton Exchange Membrane Water Electrolysis (PEMWE) is one of the most popular and widely used methods for hydrogen production. PEMWE contributes to eco-friendly system via its energy storage system application, hence making it environmentally friendly to use. However, its main drawback is contamination of proton exchange membrane during water electrolysis. Existing cation such as magnesium, calcium and the likes are the cause for membrane contamination. As a result, the cation contamination give rise to degradation of performance of electrolysis and the reverse electrolysis is effective method to remove cation.

Optimal Solidification Conditions for Suppression of Heavy Metal Elution from Water Treatment Sludge (정수슬러지로부터 중금속 용출 억제를 위한 최적 고화조건)

  • Lee, Byung-Dae;Kim, Yeoung-Chan;Lee, Jin-Shik
    • Journal of the Korean Applied Science and Technology
    • /
    • v.22 no.4
    • /
    • pp.379-384
    • /
    • 2005
  • In general, water treatment sludge (WTS) had high concentration of heavy metal, thus it made the reuse or recycling of WTS difficult. The optimal solidification conditions for maximum suppression of heavy metal elution from WTS were decided in this study. Under the optimal solidification conditions (i.e., temperature, $320^{\circ}C;$ ratio of WTS and MgO, 9:1; solidification time, 1hr), all of heavy metal including aluminum were not detected. Therefore there are no problems for reuse or recycling of WTS which was solidified under the optimal solidification conditions found in the study.