• The Korean Journal of Nuclear Medicine Technology
• /
• v.14 no.1
• /
• pp.122-126
• /
• 2010

Purpose: F-18-FPCIT that shows strong familiarity with DAT located at a neural terminal site offers diagnostic information about DAT density state in the region of the striatum especially Parkinson's disease. In this study, we altered the iteration and subset and measured SUV${\pm}$SD and Contrasts from phantom images which set up to specific iteration and subset. So, we are going to suggest the appropriate range of the iteration and subset. Materials and Methods: This study has been performed with 10 normal volunteers who don't have any history of Parkinson's disease or cerebral disease and Flangeless Esser PET Phantom from Data Spectrum Corporation. $5.3{\pm}0.2$ mCi of F-18-FPCIT was injected to the normal group and PET Phantom was assembled by ACR PET Phantom Instructions and it's actual ratio between hot spheres and background was 2.35 to 1. Brain and Phantom images were acquired after 3 hours from the time of the injection and images were acquired for ten minutes. Basically, SIEMENS Bio graph 40 True-point was used and True-X method was applied for image reconstruction method. The iteration and Subset were set to 2 iterations, 8 subsets, 3 iterations, 16 subsets, 6 iterations, 16 subsets, 8 iterations, 16 subsets and 8 iterations, 21 subsets respectively. To measure SUVs on the brain images, ROIs were drawn on the right Putamen. Also, Coefficient of variance (CV) was calculated to indicate the uniformity at each iteration and subset combinations. On the phantom study, we measured the actual ratio between hot spheres and back ground at each combinations. Same size's ROIs were drawn on the same slide and location. Results: Mean SUVs were 10.60, 12.83, 13.87, 13.98 and 13.5 at each combination. The range of fluctuation by sets were 22.36%, 10.34%, 1.1%, and 4.8% respectively. The range of fluctuation of mean SUV was lowest between 6 iterations 16 subsets and 8 iterations 16 subsets. CV showed 9.07%, 11.46%, 13.56%, 14.91% and 19.47% respectively. This means that the numerical value of the iteration and subset gets higher the image's uniformity gets worse. The range of fluctuation of CV by sets were 2.39, 2.1, 1.35, and 4.56. The range of fluctuation of uniformity was lowest between 6 iterations, 16 subsets and 8 iterations, 16 subsets. In the contrast test, it showed 1.92:1, 2.12:1, 2.10:1, 2.13:1 and 2.11:1 at each iteration and subset combinations. A Setting of 8 iterations and 16 subsets reappeared most close ratio between hot spheres and background. Conclusion: Findings on this study, SUVs and uniformity might be calculated differently caused by variable reconstruction parameters like filter or FWHM. Mean SUV and uniformity showed the lowest range of fluctuation at 6 iterations 16 subsets and 8 iterations 16 subsets. Also, 8 iterations 16 subsets showed the nearest hot sphere to background ratio compared with others. But it can not be concluded that only 6 iterations 16 subsets and 8 iterations 16 subsets can make right images for the clinical diagnosis. There might be more factors that can make better images. For more exact clinical diagnosis through the quantitative analysis of DAT density in the region of striatum we need to secure healthy people's quantitative values.

• Journal of the Korean Society of Costume
• /
• v.32
• /
• pp.313-336
• /
• 1997

Nineteen stimulus photograghs varied in hue and color scheme of one clothing style of Korean dress worn by a female were used to investigate the effect of color color scheme and structure on impression formation for Korean dress. Subjects were 77 male and 86 female undergraduate and graduate students. The stimuli c9onsisted of two sets(cool and warm) of four similar color schemes two sets (cool and warm in Chima color) of five contrasting color schemes and one extra stimulus triad 3 hue base. Structures were de-fined by color schemes of Kit.Korum toward the color schemes of Jokori and Chima. Stimu-lus photogragh selected from Korean dress fashion magazines was managed and varied in hues and color schemes to Kit Korum Jokori and Chima according to Korean Standard Color through scanning and Adobe photoshop 3.0 program and then pictured through slide printer(HR-6000). Each subject assessed 19 stimulus color photographs with incorporated 7 point semantic differential response scale. The data were analyzed by frequency mean factor analysis t-test ANOVA and Scheffe test. Results indicate impression ofrmations are af-fected by clothing cues. 1) Four factors emerged to account for dimensional structure of impressions of female features on Korean dress. These four factors were titled as(1) preference.evaluation (2) individuality.attention (3) youth and (4) friendshio. The preference.evaluation factor was the largest including eleven adjectives and accounting for 29.62% of the variances. 2) Almost every clothing cue(color, color scheme, structure) had some effects on im-pressions formed But the color of Chima did not form the effects on impression of prefer-ence.evaluation factor. The effect of related color scheme was the most influential clothing cue on impressions of preference.evalation factor and friendship factor whereas the ef-fect of contrasting color scheme was the most influential clothing cue on impressions of indi-viduality.attention factor and youth factor. The effect of cool color of Chima was the most influential clothing cue on impression of indi-viduality.attention factor whereas the effect of warm color of Chima was the most influen-tial clothing cue on impressions of youth factor and friendship factor. The effect of Jokori/Chima.Kit.Korum structure was the most influential clothing cue on impressions of pref-erence.evaluation factor and youth factor whereas the effect of Kit.Korum/Jokori.Chima structure was the most influential clothing cue on impressions of individuality.attention factor and friendship factor. 3) The interaction effects were appeared among clothing cues. Significant interaction effects between color schemes(similar and contrasting) and colors of Chima(cool and warm were appeared on impressions of prefer-ence.evaluation factor imdividuality.atten-tion factor and friendship factor, Significant interaction effects between color schemes (similar and contrasting) and structures (Jokori.Chima.Kit.Korum; Jokori.Kit.Koru-m/Chima;Jokori/Chima.Kit.Korum;Kit.Korum/Jokori.Chima) were appeared on impressions of preference.evaluation factor youth factor and friendship factor. Signifi-cant interaction effects between colors(cool and warm) and structures were appeared on impressions of individuality.attention factor youth factor and friendship factor. Sighifi-cant interaction effects between colors(cool and warm) and structures were appeared on impressions of individuality.attention factor youth factor and friendship factor. Significant interaction effects among clothing cues(color color schemes and structures) were appeared on all impression factors. The friendship factor was the most friquently affected impression factor by interaction effects among clothing cues. In summary the clothing was used as nonverbal cues in the effect on impression for-mation of female dressed in Korean dress. it concluded that color schemes worked as cen-tral traits and colors of Chima and structures worked as peripheral traits in the formation of impression of the female clothed in Korean dress. hence organizing our impressions with respect to the parts of the Korean dress in re-lation to the whole holistic perceptual pro-cess Gestalt approach was used and supported.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.46 no.4
• /
• pp.407-412
• /
• 2013

We performed four sets of feeding trials to establish optimum feed size (Exp-I), stocking density (Exp-II) and feeding frequency (Exp-III and IV) for Korean rockfish. In Exp-I, three different particle sizes of a commercial diet (small, 2.0-2.1 mm; medium, 2.4-3.2 mm; and large, 4.0-5.3 mm) were fed to four replicate groups of fish ($22.8{\pm}0.1g$), each of which was fed to apparent satiation for six weeks. In Exp-II, fish ($44.3{\pm}0.4g$) were reared at four stocking densities (1.5, 3.0, 4.5 and 6.0 $kg/m^3$) and fed a commercial diet to apparent satiation for four weeks. In Exp-III, fish ($14.8{\pm}0.1g$) were fed a commercial diet once, twice, thrice, $4{\times}$ or $5{\times}$ a day at a feeding ratio of 3.25% of body mass. Another group of fish was fed the same commercial diet $5{\times}$ a day to apparent satiation; this treatment was designated FS (five times satiation/day). In Exp-IV, fish ($31.3{\pm}0.1g$) were fed a commercial diet once, twice, thrice or $4{\times}$ a day to apparent satiation. Another group of fish was fed to apparent satiation once every 48 hours. In Exp-I, fish fed the large particle (4.0-5.3 mm) diet had a significantly higher feed conversion ratio and lower protein efficiency ratio than fish fed the small particle diet. In Exp-II, groups of fish reared at densities of 4.5 and 6.0 $kg/m^3$ had significantly higher feed intake and growth performance than fish reared at 1.5 and 3.0 $kg/m^3$. In Exp-III, fish fed to apparent satiation had significantly higher growth performances than fish fed once or $4{\times}$ a day. A significantly higher feed conversion ratio and a lower protein efficiency ratio were obtained in the FS group. In Exp-IV, growth performance and feed utilization efficiency were not significantly affected by experimental variation in feeding frequency. Fish fed to apparent satiation once every 48 hours had better feed utilization than those in other treatments and growth performances of those were comparable. Therefore, the optimum feed particle size, stocking density and feeding frequency for Korean rockfish under conditions we used were 2.0-3.2 mm, 4.5-6.0 $kg/m^3$, and once a day or once every 48 hour, respectively.

• The Korean Journal of Nuclear Medicine
• /
• v.32 no.4
• /
• pp.382-390
• /
• 1998

Purpose: The purpose of this study was to evaluate the accuracy of radioactivity quantitation in Tc-99m SPECT by using combined scatter and attenuation correction. Materials and Methods: A cylindrical phantom which simulates tumors (T) and normal tissue (B) was filled with varying activity ratios of Tc-99m. We acquired emission scans of the phantom using a three-headed SPECT system (Trionix, Inc.) with two energy windows (photopeak window: $126{\sim}154keV$ and scatter window: $101{\sim}123keV$). We performed the scatter correction with dual-energy window subtraction method (k=0.4) and Chang attenuation correction. Three sets of SPECT images were reconstructed using combined scatter and attenuation correction (SC+AC), attenuation correction (AC) and without any correction (NONE). We compared T/B ratio, image contrast [(T-B)/(T+B)] and absolute radioactivity with true values. Results: SC+AC images had the highest mean values of T/B ratios. Image contrast was 0.92 in SC+AC, which was close to the true value of 1, and higher than AC (0.77) or NONE (0.80). Errors of true activity by SPECT images ranged from 1 to 11% for SC+AC, $22{\sim}47%$ for AC, and $2{\sim}16%$ for NONE in a phantom which was located 2.4cm from the phantom surface. In a phantom located 10.0cm from the surface, SC+AC underestimated by 24%, NONE 40%. However, AC overestimated by 10%. Conclusion: We conclude that accurate SPECT activity quantitation of Tc-99m distribution can be achieved by dual window scatter correction combind with attenuation correction.

• Nuclear Engineering and Technology
• /
• v.39 no.5
• /
• pp.603-616
• /
• 2007

Roy Huddle, having invented the coated particle in Harwell 1957, stated in the early 1970s that we know now everything about particles and coatings and should be going over to deal with other problems. This was on the occasion of the Dragon fuel performance information meeting London 1973: How wrong a genius be! It took until 1978 that really good particles were made in Germany, then during the Japanese HTTR production in the 1990s and finally the Chinese 2000-2001 campaign for HTR-10. Here, we present a review of history and present status. Today, good fuel is measured by different standards from the seventies: where $9*10^{-4}$ initial free heavy metal fraction was typical for early AVR carbide fuel and $3*10^{-4}$ initial free heavy metal fraction was acceptable for oxide fuel in THTR, we insist on values more than an order of magnitude below this value today. Half a percent of particle failure at the end-of-irradiation, another ancient standard, is not even acceptable today, even for the most severe accidents. While legislation and licensing has not changed, one of the reasons we insist on these improvements is the preference for passive systems rather than active controls of earlier times. After renewed HTGR interest, we are reporting about the start of new or reactivated coated particle work in several parts of the world, considering the aspects of designs/ traditional and new materials, manufacturing technologies/ quality control quality assurance, irradiation and accident performance, modeling and performance predictions, and fuel cycle aspects and spent fuel treatment. In very general terms, the coated particle should be strong, reliable, retentive, and affordable. These properties have to be quantified and will be eventually optimized for a specific application system. Results obtained so far indicate that the same particle can be used for steam cycle applications with $700-750^{\circ}C$ helium coolant gas exit, for gas turbine applications at $850-900^{\circ}C$ and for process heat/hydrogen generation applications with $950^{\circ}C$ outlet temperatures. There is a clear set of standards for modem high quality fuel in terms of low levels of heavy metal contamination, manufacture-induced particle defects during fuel body and fuel element making, irradiation/accident induced particle failures and limits on fission product release from intact particles. While gas-cooled reactor design is still open-ended with blocks for the prismatic and spherical fuel elements for the pebble-bed design, there is near worldwide agreement on high quality fuel: a $500{\mu}m$ diameter $UO_2$ kernel of 10% enrichment is surrounded by a $100{\mu}m$ thick sacrificial buffer layer to be followed by a dense inner pyrocarbon layer, a high quality silicon carbide layer of $35{\mu}m$ thickness and theoretical density and another outer pyrocarbon layer. Good performance has been demonstrated both under operational and under accident conditions, i.e. to 10% FIMA and maximum $1600^{\circ}C$ afterwards. And it is the wide-ranging demonstration experience that makes this particle superior. Recommendations are made for further work: 1. Generation of data for presently manufactured materials, e.g. SiC strength and strength distribution, PyC creep and shrinkage and many more material data sets. 2. Renewed start of irradiation and accident testing of modem coated particle fuel. 3. Analysis of existing and newly created data with a view to demonstrate satisfactory performance at burnups beyond 10% FIMA and complete fission product retention even in accidents that go beyond $1600^{\circ}C$ for a short period of time. This work should proceed at both national and international level.

• Journal of Korean Philosophical Society
• /
• v.129
• /
• pp.23-51
• /
• 2014

Christine M. Korsgaard believes that constructivism can respond to moral skepticism without depending upon moral realism. The purpose of this paper is to examine Korsgaard's kantian constructivism and her positions on moral realism. According to Korsgaard moral realism cannot answer normative questions in that it sees the function of moral concepts as describing the reality and so accepts the model of applied knowledge for action. In contrast Korsgaard insists that constructivism is better at justifying normativity since it regards moral concepts as representing the solutions to practical problems and so shows that moral principles are necessarily involved in the practical problems of agency. Korsgaard's constructivism has antirealistic elements such as pure proceduralism, the constitutive model to exclude ontological, metaphysical meanings, and the account of human beings as the sources of values. In spite of those antirealistic elements it is difficult to jump to a conclusion that Korsgaard's constructivism is antirealism. Korsgaard, in the early book, The Sources of Normativity, says that kantian constructivism has something to do with a form of realism, or procedural moral realism. And in the following books she argues that constructivism is compatible with realism although she pays attention to the practical implications of constructivism and then sets aside its ontological relevance. That is, Korsgaard does not want that her constructivism results in antirealism. Korsgaard's realism, however, is too weak to be called as realism. There is, also, a question why one would rather take a constructivist approach if one holds on to realism.

• Journal of Korea Water Resources Association
• /
• v.54 no.spc1
• /
• pp.1095-1105
• /
• 2021

The advancement of dam operation is further required due to the upcoming rainy season, typhoons, or torrential rains. Besides, physical models based on specific rules may sometimes have limitations in controlling the release discharge of dam due to inherent uncertainty and complex factors. This study aims to forecast the water level of the nearest station to the dam multi-timestep-ahead and evaluate the availability when it makes a decision for a release discharge of dam based on LSTM (Long Short-Term Memory) of deep learning. The LSTM model was trained and tested on eight data sets with a 1-hour temporal resolution, including primary data used in the dam operation and downstream water level station data about 13 years (2009~2021). The trained model forecasted the water level time series divided by the six lead times: 1, 3, 6, 9, 12, 18-hours, and compared and analyzed with the observed data. As a result, the prediction results of the 1-hour ahead exhibited the best performance for all cases with an average accuracy of MAE of 0.01m, RMSE of 0.015 m, and NSE of 0.99, respectively. In addition, as the lead time increases, the predictive performance of the model tends to decrease slightly. The model may similarly estimate and reliably predicts the temporal pattern of the observed water level. Thus, it is judged that the LSTM model could produce predictive data by extracting the characteristics of complex hydrological non-linear data and can be used to determine the amount of release discharge from the dam when simulating the operation of the dam.

• Journal of Bio-Environment Control
• /
• v.31 no.4
• /
• pp.460-467
• /
• 2022

The purpose of this study is to enhance utilization of the waste nutrient solution (WNS) disposed at the hydroponic greenhouse. Several sets of testing were conducted to examine the effects of WNS: (a) a fertilizer effect, (b) soil column leaching, and (c) crop cultivation. The fertilizer effect test was applied in young radish cultivation by examining the growth characteristics of young radish and soil based on inorganic nitrogen according to the soil treatment of the nitrogen fertilizer (NF) and the WNS. The fertilizer effects and crop cultivation test were conducted with five treatments (A-E): A, non-treatment (water); B, 100% of NF; C, 70% of NF + 30% of WNS; D, 50% of NF + 50% of WNS; and E, 30% of NF + 70% of WNS. The soil column leaching test was conducted with three treatments: non-treatment (water), 100% of NF, 50% of WNS + 50% of NF. As a result, the chemical properties of the WNS were pH 6.0, EC 2.4dS·m^-1, total phosphorus (T-P) 28mg·L^-1, ammonium nitrogen (NH₄-N) 5.0mg·L^-1, and nitrate nitrogen (NO₃-N) 301mg·L^-1. The chemical properties of the soil were pH 5.51, EC 0.31dS/m, organic matter 2.08g·kg^-1, NO₃-N 9.64mg·kg^-1, and NH₄-N 3.20mg·kg^-1. The results of fertilizer effects showed that the ratio of 50% or less of NF and 50% or more of WNS was high in young radish growth. There was no statistically significant difference between the soil chemistry in the C-E treatments where WNS was mixed with NF and the B treatment where only NF was applied. As a result of the soil column leaching test, there was no significant difference in the concentrations of NO₃ and NH₄ in the treatment of 100% of NF and 50% of NF + 50% of WNS. The study indicates, if the mixed fertilizer of WNS and NF is applied in the soil cultivation of young radish, it will reduce the use of NF and environmental pollution. This also helps reduce production costs on farmers and increase the yield of young radish.

• Journal of Wetlands Research
• /
• v.20 no.2
• /
• pp.155-160
• /
• 2018

We investigated to know the growth patterns of Aedes albopictus larva at the four different temperature conditions. Each of 120 individuals was placed into a $20m{\ell}$ vial and 12 sets (a set of 10 vials) were separated into 12 water tanks ($17{\times}24{\times}18cm^3$). Each water tank was composed of 3 the $1^{st}$ instar, 3 the $2^{nd}$ instar, 2 the $3^{rd}$ instar, and 2 the $4^{th}$ instar. Three sets of water tanks were placed under the four different incubator temperatures ($17^{\circ}C$, $21^{\circ}C$, $24^{\circ}C$, $28^{\circ}C$). We found that the eclosion rates were $20.00{\pm}5.77%$ at $21^{\circ}C$ and $3.33{\pm}3.33%$ at other temperatures. For the mosquito larva mortality rate, $1^{st}$ instar was $19.24{\pm}3.65%$, $2^{nd}$ instar was $16.48{\pm}3.25%$, $3^{rd}$ instar was $23.54{\pm}5.06%$, and $4^{th}$ instar was $40.74{\pm}7.08%$. The lowest mortality rate in growth stages according to temperature was $13.33{\pm}6.67%$ at $17^{\circ}C$ in $1^{st}$ instar larva, $7.41{\pm}7.41%$ at $21^{\circ}C$ at $2^{nd}$ instar larva, $10.74{\pm}6.43%$ at $24^{\circ}C$ in $3^{rd}$ instar larva, and $20.37{\pm}5.46%$ at $28^{\circ}C$ in $4^{th}$ instar larva. The survival period of mosquitoes in underwater were $26.33{\pm}0.67days$ at $17^{\circ}C$, $23.33{\pm}1.33days$ at $21^{\circ}C$, $20.00{\pm}2.52days$ at $24^{\circ}C$, and $11.67{\pm}1.20days$ at $28^{\circ}C$. From our results the most effective temperature to the normal growth of mosquito larva was $21^{\circ}C$, and the highest mortality rate was shown at the $4^{th}$ instar stage of larva growth. Our results would provide the basic data for the mosquito larva's growth pattern.

• Asian-Australasian Journal of Animal Sciences
• /
• v.27 no.11
• /
• pp.1540-1547
• /
• 2014

The accuracy of genomic estimated breeding values (GEBV) was evaluated for sixteen meat quality traits in a Berkshire population (n = 1,191) that was collected from Dasan breeding farm, Namwon, Korea. The animals were genotyped with the Illumina porcine 62 K single nucleotide polymorphism (SNP) bead chips, in which a set of 36,605 SNPs were available after quality control tests. Two methods were applied to evaluate GEBV accuracies, i.e. genome based linear unbiased prediction method (GBLUP) and Bayes B, using ASREML 3.0 and Gensel 4.0 software, respectively. The traits composed different sets of training (both genotypes and phenotypes) and testing (genotypes only) data. Under the GBLUP model, the GEBV accuracies for the training data ranged from $0.42{\pm}0.08$ for collagen to $0.75{\pm}0.02$ for water holding capacity with an average of $0.65{\pm}0.04$ across all the traits. Under the Bayes B model, the GEBV accuracy ranged from $0.10{\pm}0.14$ for National Pork Producers Council (NPCC) marbling score to $0.76{\pm}0.04$ for drip loss, with an average of $0.49{\pm}0.10$. For the testing samples, the GEBV accuracy had an average of $0.46{\pm}0.10$ under the GBLUP model, ranging from $0.20{\pm}0.18$ for protein to $0.65{\pm}0.06$ for drip loss. Under the Bayes B model, the GEBV accuracy ranged from $0.04{\pm}0.09$ for NPCC marbling score to $0.72{\pm}0.05$ for drip loss with an average of $0.38{\pm}0.13$. The GEBV accuracy increased with the size of the training data and heritability. In general, the GEBV accuracies under the Bayes B model were lower than under the GBLUP model, especially when the training sample size was small. Our results suggest that a much greater training sample size is needed to get better GEBV accuracies for the testing samples.