• Journal of the Korea Furniture Society
• /
• v.17 no.2
• /
• pp.9-23
• /
• 2006

Control particleboards were significantly higher in thickness swelling than wood particle-polypropylene fiber composites and their thickness swelling increased with the increase of target density. In the composites, thickness swelling did not vary significantly with the increase of target density but increased with the increase of wood particle content. And the composites with fine wood particles were significantly lower in thickness swelling than those with coarse wood particles irrespective of target density and formulation. In the scanning electron microscopy, significantly higher thickness swelling in the composites with coarse wood particles was thought to be the result of more interfacial separations by higher swelling stresses.

• Journal of radiological science and technology
• /
• v.21 no.2
• /
• pp.19-25
• /
• 1998

By analyzing each part of expsure condition and the status of an entrance dose which is exposed to patients, this study reached the following conclusion. Since there is no standard in setting up an exposure condition, the technology practiced in each facility varies tremendously, and the entrance dose increased especially due to the improper selection of screen and grid and the shortage of a total amount of filtration in leaching the standard filtration amount. Entrance dose was, generally, turned out to be $2{\sim}3$ times as much as that of advanced countries, and there was big difference between facilities ; approximately 52 times inlateral of cervical vertebrae, 35 times in A-P of femur, 33 times in chest A-P, and 11 times in lumber A-P. Therefore, to minimize the entrance dose of a patient with thegreatest amount of image information, acquirement of technological know-how necessary for standardization of exposure condition for each part can be an important research task.

• Journal of the Korean Wood Science and Technology
• /
• v.19 no.2
• /
• pp.65-71
• /
• 1991

본 연구는 CCA 처리재의 재건조(再乾燥)시 적용된 건조 스케쥴 (통상(通常) 열기건조(熱氣乾燥)와 고온건조(高溫乾燥) 스케쥴)이 처리재의 휨강도(强度) 성질에 미치는 영향을 고찰하고자 수행되었다. 탄성계수(彈性係數)(MOE), 그리고 비파괴시험(非破壞試驗)에 의해 얻어진 동적(動的) 탄성계수 (Dynamic MOE) 및 대수감쇠율(對數減衰率)(Logarithmic decrement) 은 처리후 재건조에 의해 큰 영향을 받지 않았다. 반면에 적용된 건조 스케쥴에 관계없이 재건조시 심각한 파괴계수(破壞係數)(MOR)의 감소가 파괴계수 분포의 모든 영역에서 초래되었다. 그러나 통상 열기건조(최대 건구온도=$71^{\circ}C$)와 고온건조(건구온도=$110^{\circ}C$) 서로간에는 감소의 정도에 큰 차이가 없었다. 따라서, 처리재의 재건조사 심각한 파괴계수의 감소가 용인(容認)되지 않는다면 CCA로 처리된 Lodgepole pine 각재의 재건조는 미국 연방 임산물 시험장의 Lodgepole pine의 통상 열기건조 스케쥴 (T9-C3) 보다 온화(溫和)한 조건으로 실시되어야 할 것이다.

• Journal of the Korean Wood Science and Technology
• /
• v.35 no.5
• /
• pp.1-6
• /
• 2007

Boiling-in-oil process was performed to investigate the high-temperature drying characteristics of 25, 50, and 70 mm-thick flat-sawn Douglas-fir lumber. Drying rates, moisture profiles and temperature profiles were monitored. Fully refined paraffin wax was used as drying agent and heated to $130^{\circ}C$. Average drying rates of 25, 50, and 70 mm-thick specimen were 11.6, 6.7, 5.0%/h, respectively. The moisture content differences between cores and ends were 1~2% in 25 mm-thick and 200 mm-long sample and over 10% in 50 mm-thick and 600 mm-long sample.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.10a
• /
• pp.634-638
• /
• 1997

The objectives of this research are to develop lumber and lower-thoracic pedicle fixation system for Korean patients. To achieve the aimed goals, first, optimized shape design process is performed, and finite element methods are applied to evaluate the mechanical strength of the developed fixation system. Second, appropriate machining experiments are carried out to develop optimum machining conditions for titan~um alloys those are known as one of the most difficult-to-cut material. As the results of this research, new pedicle screw system, considering the morphological characteristics of Korean patients, is developed by applying the finite element analysis, optimum shape processing method and optimize design algorithm.

• Journal of the Korea Furniture Society
• /
• v.26 no.4
• /
• pp.467-473
• /
• 2015

Natural dyeing is considered to be an alternative to chemical staining in terms of harmful VOC-free and environmentally-friendly ingredient. This study was concerned with an evaluation of color performance of naturally dyed- and painted veneer for cylindrical laminated veneer lumber etc. according to the used condition in terms of existence of light and heat in drying. From the results, the color changes by the color of dyed veneer and the type of paint are likely to be affected by fading condition of light or heat. In the future, long-term outdoor exposure test needs to be additionally followed in order to evaluate durable usability of colored veneers.

• Journal of the Korea Furniture Society
• /
• v.19 no.5
• /
• pp.350-357
• /
• 2008

This research investigates the bending properties to predict the work-energy to maximum load and impact bending energy from static bending and impact bending test. Specimens were prepared from lumber made of thinning crop-trees. Matched specimens were used for MC 12% and green moisture specimens to measure the effect of moisture content on the absorbed energy from static and impact bending tests. The bending properties such as MOE, MOR, etc. is a good predictor to investigate the work-energy and work-energy per unit volume from static bending and impact bending test. The impact bending energy is increased with increasing moisture content. However, the work to maximum load from static bending test is increasing with increasing the MC only for higher density species.

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.7
• /
• pp.147-155
• /
• 2000

To reduce the noise from wood cutting saw at the saw mill(lumber mill) or a construction area, some multi-layer sandwich saw blades which a aluminum or copper plate was inserted between the two steel plates were developed and were tested of the wood cutting noise level at various test places. From the research, it was found that the multi-layer saw blade with copper or aluminum plate between steel plates and spot welded 60 points could reduce the wood cutting sound level about 8.3 dB(97.031 dB - 88.743 dB) at indoor test and 3.8 dB(84.805 - 81.638 dB) at field test.

• Journal of the Korean Wood Science and Technology
• /
• v.8 no.2
• /
• pp.9-16
• /
• 1980

The problem of tauns having the characteristics of severe variations in quality and unequally distributed moisture content in veneer sheets after drying for plywood could be cured to a proper even moisture distribution by the peeling of veneers in a prolonged period. The poor gluability of tauns was improved by applicaton of increased resin content of glue in spreading. Combinations of tauns with lauan and kapur for plywood showed good shear strength.

• Journal of the Korean Wood Science and Technology
• /
• v.26 no.1
• /
• pp.1-6
• /
• 1998

손가락결합부재에 대한 정적휨시험 및 초음파 비파괴시험을 실시하였다. 발신 및 수신 변환기의 상대 위치와 두 변환기 사이의 거리에 따른 음전달속도의 변화를 분석하였으며 정적 휨시험으로 부터 구한 MOE 및 MOR과 비교하였다. MOR과 음전달속도는 손가락의 경사가 증가할수록 감소하였다. MOR은 음전달속도와 매우 밀접한 상관관계를 보였으나 MOE는 손가락의 경사도나 음전달속도에 큰 영향을 받지 않는 것으로 나타났다. 음전달속도는 섬유방향이 방사방향이나 접선방향에 비하여 더 높은 값을 나타내었다. 발신 및 수선 변환기를 동일면에 부착한 경우에 직각면 또는 반대면에 부착한 경우보다 더 높은 음전달속도를 나타내었다. 변환기 사이의 거리가 증가할수록 음전달속도는 양끝면에 변환기를 부착한 경우의 속도에 수렴하는 경향을 나타내었다.