• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.65-68
• /
• 2004

A new multifunctional sandwich composite was investigated in this paper. The honeycomb core of this composite was filled with viscoelastic material in order to obtain an improved impact performance. The fillings in the honeycomb cells was hoped to provide the act of energy dissipation in this combined material system. Low-velocity drop-weight test was set up to the specimens with various stacked carbon/epoxy laminate facesheets, $[0/90]_{4s},\;[0/45/-45/90]_{2s}$. Load and energy history were checked and compared for the both groups of specimens, with and without rubber fillings. Further, the damaged faces were inspected visually by ultrasonic C-scan.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.138-146
• /
• 2012

This research is to analyze the wave propagation characteristics of anisotropic materials subjected to the low-velocity impact. For this purpose, a higher-order finite element program is used to simulate the dynamic behaviors according to the changes of material property, stacking sequence and dimension etc.. Materials for simulation are composed of $[0^{\circ}]_{10s}$, $[45^{\circ}/-45^{\circ}]_{5s}$ and $[90^{\circ}]_{10s}$ stacking sequences. Finally, the results of this simulation are compared with those of wave propagation theory and then the impact responses and wave propagation phenomena are investigated.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.5 no.1
• /
• pp.141-148
• /
• 2001

Dynamic compaction is the ground improvement method by applying the impact energy. This impact energy can damage to adjacent structure in urban area. Therefore, if dynamic compaction method is applied, careful attention should be payed to surrounded structures. In this study, the method was performed in waste landfill and the frequency of vibrations were measured according to each distances, drop-heights, and vibrating directions. The measured data show that particle velocity bas low frequency and it is greatest in longitudinal direction. There was little differences between Maynes suggestion and measured data. Therefore, Maynes suggestion can be adopted if the range of vibration can be predicted. Also, It was found that minimum 45m distance is needed in order to satisfy the administrative code if dynamic compaction method is applied.

• Composites Research
• /
• v.15 no.2
• /
• pp.11-17
• /
• 2002

The piezoelectric thin film sensor can be used to interpret variations in structural and material properties, e.g. for structural integrity monitoring and assessment. To illustrate one of this potential benefit, PVDF (polyvinylidene fluoride) film sensors are used for monitoring impact damage in Gr/Ep composite panels. Both PVDF film sensors and strain gages are attached to the surface of Gr/Ep specimens. A series of impact tests at various impact energy by changing impact mass the height are performed on the instrumented drop weight impact tester. The sensor responses are carefully examined to predict the onset of impact damage such as indentation, matrix cracking, and delamination, etc. Test results show that the particular waveforms of sensor signals implying the damage initiation and development are detected above the damage initiation impact energy. As expected, the PVDF film sensor is found to be more sensitive to impact damage initiation event than the strain gage.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.8 no.3
• /
• pp.163-170
• /
• 2000

Accident statistics shows that the portion of fatal occupant injuries due to side impacts is considerably high. The side impact usually leads to a severe intrusion of side structure into the passenger compartment. Furthermore, the safety zone for the side impact is relatively small compared to the front impact. Those kinds of physics for side impact frequently result in a fatal injury for the occupant. Therefore, NHTSA and EEVC are trying to intensify the regulation for the occupant protection against side impact. Both the regulation and recent market trends are asking for an installation of side airbag. There are several types of system configuration for side impact sensing. In this paper, we adopt the acceleration-based remote sensing method for the side airbag control system. We mainly focus on the development of hardware and crash discrimination algorithm of remote sensing unit. The crash discrimination algorithm needs fast decision of airbag firing especially for high-speed side impact such as FMVSS 214 and EEVC tests. It is also required to distinguish between low-speed fire and no-fire events. The algorithm should have a sufficient safety margin against any misuse situation such as hammer blow, door slam, etc. This paper introduces several firing criteria such as acceleration. velocity and energy criteria that use physical value proportional to crash severity. We have made a simulation program by using Matlab/Simulink to implement the proposed algorithm. We have conducted an algorithm calibration by using real crash data for 2,500cc vehicle. The crash performance obtained by the simulation was verified through a pulse injection method. It turned out that the results satisfied the system requirements well.

• Journal of Environmental Impact Assessment
• /
• v.9 no.2
• /
• pp.109-117
• /
• 2000

The dynamics of physico-chemical factors and biomass of epilithic attached algae was determined by bimonthly sampling in the Kyechon and Yudongchon situated in the upper part of Som River from March 1998 to February 1999. Among environmental factors, average of $NH_4$, $NO_3$, SRP and SRSi concentration ranged $8.9{\sim}86.6{\mu}g$ N/l, $663.9{\sim}2,018.1{\mu}g$ N/l, $0{\sim}15.0{\mu}g$ P/l and 1.6~2.6 mg Si/l, respectively. The contents of chlorophyll-a and organic matter per unit area, which ranged from 21.1 to 231.8 $mg/m^2$ and ranged from 5.2 to 52.6 $g/m^2$, respectively, showed very high in the spatial and temporal variations. Both were high in February and May and low in March seasonally. The fluctuation of epilithic biomass related the concentration of $NH_4$, SRP and current velocity. In relationship between biomass and current velocity, >200 and 100~200 mg chl-a/$m^2$ corresponded to <0.2 and <0.8 m/s, respectively. The evaluation of water quality with chl-a and organic matter of periphyton resulted on over eutrophic condition. Periphytic algae in a small stream were more effective as indicator of water quality than planktonic algae. More researches on periphytic algae in relation to water quality evaluation are needed.

• The Journal of the Korea Contents Association
• /
• v.8 no.8
• /
• pp.244-252
• /
• 2008

This research differentiate the technique of Jungkwon-jirugi, one of the basic movements of Taekwondo, into two movements stop-jirugi and push-jirugi and gives analysis of the impulse, acceleration and velocity in the point of motor control. For this, we tried graphic analysis using an acceleration sensor and high speed camera which was made from USA in 2005 and took pictures at 250 frames per second. We reached the following conclusions. First, the acceleration wave of push-jirugi was a period longer than stop-jirugi, meaning that the push-jirugi motion asserts force for a longer time. Second, the acceleration and velocity graph shows that the highest velocity occurs on the point when the acceleration begins to decrease right after reaching its maximum. Third, according to the image analysis using the high speed camera, we could find out that the shoulder is pushed a little even in the stop-jirugi motion.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.28 no.6
• /
• pp.890-898
• /
• 2022

Dispersion of suspended sediment, caused by coastal and marine development, is a key item in assessing marine environmental impact as it adversely affects marine life by increasing the level of turbidity and decreasing the amount of sunlight in seawater. However, its estimation has not been reliable because of the absence of a standard for the data measurement and divergent approaches to the impact assessment. In this study, we examined the estimation models from 58 Marine Environmental Impact Statements (MEISs, 2012-2014) to identify the gaps in the assessment and devise ways of improving the estimation. We developed four index items-grid system; unit load, particle size, and settling velocit-to evaluate their reliability in the estimation. The mean reliability score of each index was overall low-25 for grid system, 60 for unit load, 34 for particle size, and 17 for settling velocity. To ensure high reliability, it is important to develop a standard guideline that defines precise measurement of suspended sediment for unit load and settling velocity by particle size, followed by a grid system with compatible size for modelling. This can improve the estimation and thus underlie coherent impact assessment of suspended sediment dispersion on marine environment.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.26 no.5
• /
• pp.932-938
• /
• 2002

In structural applications, brittle materials such as soda-lime glasses and ceramics are usually subjected to multiaxial stress state. Brittle materials with cracks or damage by foreign object impacts are apt to fracture abruptly from cracks, because of their properities of very high strength and low fracture toughness. But in most cases, the residual strength of structural members with damage has been tested under uniaxial stress condition such as the 4-point bend test. Depending upon the crack pattern developed, the strength under multiaxial stress state might be different from the one under uniaxial. A comparative study was carried out to investigate the influence of stress state on the residual strength evaluation. In comparable tests, the residual strength under biaxial stress state by the ball-on-ring test was greater than that under the uniaxial one by the 4-point bend test, when a small size indendation crack was introduced. In the case that crack having an angle of 90deg. to the applied stress direction, the ratio of biaxial to uniaxial flexure strength was about 1.12. The residual strength was different from crack angles to loading direction when it was evaluated by the 4-point bend test. The ratio of residual strength of 45deg. crack to 90deg. one was about 1.20. In the case of specimen cracked by a spherical impact, it was shown that an overall decrease in flexure strength with increasing impact velocity, and the critical impact velocity for formation of a radial and/or cone crack was about 30m/s. In those cases that relatively large cracks were developed as compared with the case of indented cracks, the ratio of residual strength under biaxial stress state to one uniaxial became small.

• International Journal of Automotive Technology
• /
• v.6 no.6
• /
• pp.643-655
• /
• 2005

The frontal crash optimization of S-shaped closed-hat section member using the homogenization method, design of experiment (DOE) and response surface method (RSM) was studied. The optimization to effectively absorb more crash energy was studied to introduce the reinforcement design. The main focus of design was to decide the optimum size and thickness of reinforcement. In this study, the location of reinforcement was decided by homogenization method. Also, the effective size and thickness of reinforcements was studied by design of experiments and response surface method. The effects of various impact velocity for reinforcement design were researched. The high impact velocity reinforcement design showed to absorb the more crash energy than low velocities design. The effect of size and thickness of reinforcement was studied and the sensitivity of size and thickness was different according to base thickness of model. The optimum size and thickness of the reinforcement has shown a direct proportion to the thickness of base model. Also, the thicker the base model was, the effect of optimization using reinforcement was the bigger. The trend curve for effective size and thickness of reinforcement using response surface method was obtained. The predicted size and thickness of reinforcement by RSM were compared with results of DOE. The results of a specific dynamic mean crushing loads for the predicted design by RSM were shown the small difference with the predicted results by RSM and DOE. These trend curves can be used as a basic guideline to find the optimum reinforcement design for S-shaped member.