• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.19 no.12
• /
• pp.1106-1111
• /
• 2006

To improve warpage, delamination and the chemical reaction between 2 different co-fired materials, the bonding behavior with common glass was studied. As shown in the previous paper, the phenomenon of the infiltration is different with the composition of the glass. In particular, in the case of low temperature melting glass, infiltration is experimented in this study. GA-1 glass is infiltrated among $BaTiO_3$ particles below $800^{\circ}C$ and is made by glass/ceramic composite. Until the laminate is fired under $850^{\circ}C$, provskite phase is observed. Although in the case of GA-12 glass, the temperature of the glass infiltration is lower than it of GA-l glass, the perovskite phase already disappears at $800^{\circ}C$. As a result, GA-1 and GA-12 glasses are infiltrated among particles at low temperature, however, the chemical reactivity of the glass/ceramic and sintering temperature should be considered.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.17 no.9
• /
• pp.942-946
• /
• 2004

The crystalline and dielectric properties on Al$_2$O$_3$ filled glass frit (CaO-Al$_2$O$_3$-SiO$_2$-MgO-B$_2$O$_3$) with admixtures of TiO$_2$ have been investigated. The dielectric constant value of 7.5 ∼ 7.8, qualify factor value of 700 were obtained for glass frit : Al$_2$O$_3$(50 : 50 wt%) ceramics. Addition of TiO$_2$ less than 5 wt% slightly increased the dielectric constant from 7.8 to 8.8 due to higher dielectric constant of TiO$_2$. With increasing the amount of TiO$_2$ up to 5 wt%, the temperature coefficient of dielectric properties was improved. When the TiO$_2$ 5 wt% were added, dielectric properties were dielectric constant 8.8, quality factor 840 and the temperature coefficient of dielectric 45 ppm/$^{\circ}C$ at a sintering temperature 920$^{\circ}C$.

• Journal of the Microelectronics and Packaging Society
• /
• v.19 no.4
• /
• pp.79-83
• /
• 2012

LTCC (Low temperature co-fired ceramic) package have been paid much attention due its good reliability, miniaturization, and application of silver paste with complex wiring and printing. Therefore, LTCC package has been expected to replace vulnerable plastic package in the field of high power LED device. Currently, LTCC ceramic package is mainly made up of aluminum oxide powder. In this study, zinc oxide powder is added or replaced for the fabrication of LTCC ceramic body. By adding small amount of ZnO, thermal conductivity of the LTCC ceramic body could be remarkably increased by 25% leading to the extension of LED life time. The LTCC package structure with composition including ZnO has an increased thermal flux by 56% as a result of ANSYS simulation. Actually, the fabricated LED package with the addition of ZnO exhibits a decreased thermal resistivity by 14.9%.

• Journal of the Korean Ceramic Society
• /
• v.53 no.6
• /
• pp.682-688
• /
• 2016

In $TiO_2$-CuO systems, low-temperature sinterability was investigated by a conventional sintering method. Sintering temperatures were set at under $950^{\circ}C$, at which the volume diffusion is inactive. The temperatures are less than the melting point of Ag ($961^{\circ}C$), which is often used as an internal conductor in low-temperature co-fired ceramic technology. To optimize the amount of CuO dopant, various dopant contents were added. The optimum level for enhanced densification was 2 wt% CuO. Excess dopants were segregated to the grain boundaries. The segregated dopants supplied a high diffusion path, by which grain boundary diffusion improved. At lower temperatures in the solid state region, grain boundary diffusion was the principal mass transport mechanism for densification. The enhanced grain boundary diffusion, therefore, improved densification. In this regard, the results of this study prove that the sintering mechanism was the same as that of activated sintering.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.3
• /
• pp.215-218
• /
• 2011

A novel design of gas sensor using Ga-doped ZnO (GZO) thin films which are deposited on low temperature co-fired ceramic (LTCC) substrates is presented. The LTCC substrates with thickness of 400 ${\mu}m$ are fabricated by laminating 12 green tapes which consist of alumina and glass particle in an organic binder. The GZO thin films with different thickness are deposited on LTCC substrates, by RF magnetron sputtering method. The microstructure and sensing properties of GZO gas sensing films are analyzed as a function of the film thickness. The films are well crystallized in the hexagonal (wurzite) structure with increasing thickness. The maximum sensitivity of 3.49 is obtained at 100 nm film thickness and the fastest 90% response time of 27.2 sec is obtained at 50 nm film thickness for the operating temperature of $400^{\circ}C$ to the $NO_2$ gas.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.51-54
• /
• 2007

The purpose of this paper is the development of measurement algorithm for green-sheet based on the digital image processing technique. The Low Temperature Cofired Ceramic (LTCC) technology can be defined as a way to produce multilayer circuits with the help of single tapes, which are used to apply conductive, dielectric and / or resistive pastes on. These single green-sheets have to be laminated together and fired in one step all. Main functionality of the green-sheet film measurement algorithm is to measure the position and size of the punching hole in each single layer. The line scan camera coupled with motorized X-Y stage is used for developing the algorithm. In order to measure the entire film area using several scanning steps, the overlapping method is used. In the process of development of the algorithm based on the image processing and analysis, strong background technology and know-how have been accumulated.

• ETRI Journal
• /
• v.41 no.6
• /
• pp.811-819
• /
• 2019

We propose a substrate with high thermal conductivity, manufactured by the low-temperature co-fired ceramic (LTCC) multilayer circuit process technology, as a new DC/DC converter platform for power electronics applications. We compare the reliability and power conversion efficiency of a converter using the LTCC substrate with the one using a conventional printed circuit board (PCB) substrate, to demonstrate the superior characteristics of the LTCC substrates. The power conversion efficiencies of the LTCC- and PCB-based synchronous buck converters are 95.5% and 94.5%, respectively, while those of nonsynchronous buck converters are 92.5% and 91.3%, respectively, at an output power of 100 W. To verify the reliability of the LTCC-based converter, two types of tests were conducted. Storage temperature tests were conducted at -20 ℃ and 85 ℃ for 100 h each. The variation in efficiency after the tests was less than 0.3%. A working temperature test was conducted for 60 min, and the temperature of the converter was saturated at 58.2 ℃ without a decrease in efficiency. These results demonstrate the applicability of LTCC as a substrate for power conversion systems.

• Journal of electromagnetic engineering and science
• /
• v.3 no.1
• /
• pp.35-38
• /
• 2003

In this paper, compact lumped-element low-pass filter structure with two transmission zeros at second and third harmonics is presented. The use of lumped-elements and transmission zeros can provide the advantages of compact size, sharp cutoff and wide stop-band frequency response. The proposed low-pass filter is a modified Chebyshev low-pass filter type and is implemented by the use of low temperature co-fired ceramic (LTCC) technology. This filter has been verified by both simulation and experiment. The simulated and experimental results agree very well.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.4
• /
• pp.362-370
• /
• 2010

In this paper, a compact RF Front-end module for Wireless Fidelity(Wi-Fi) and Worldwide Interoperability for Microwave Access(WiMAX) applications is realized by low temperature co-fired ceramic(LTCC) technology. The RF Front-end module is composed of three LTCC band-pass filters, a Film Bulk Acoustic Resonator(FBAR) filter, fully embedded matching circuits, an SPDT switch for mode selection, an SPDT switch for Tx/Rx selection, and an SP4T switch for band selection. The parasitic elements of 0.2~0.3 pF are generated by the structure of stacking in the top pad pattern for DC block capacitor of SPDT switch for mode selection. These kinds of parasitic elements break the matching characteristic, and thus, the overall electrical performance of the module is degraded. In order to compensate it, we insert a parallel lumped-element inductor on capacitor pad pattern for DC block, so that we obtain the optimized performance of the RF Front-end module. The fabricated RF front-end module has 12 layers including three inner grounds and it occupies less than $6.0mm{\times}6.0mm{\times}0.728mm$.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.154-161
• /
• 2011

This paper presents a compact integrated transceiver module for 2.4 GHz band applications using Low Temperature Co-fired Ceramic(LTCC) technology. The implemented transceiver module is divided into an RF Front-End Module (FEM) part and a transceiver IC chip part. The RF FEM part except an SPDT switch and DC block capacitors is fully embedded in the LTCC substrate. The fabricated RF FEM has 8 pattern layers and it occupies less than $3.3\;mm{\times}5.2\;mm{\times}0.4\;mm$. The measured results of the implemented RF FEM are in good agreement with the simulated results. The transceiver IC chip part consists of signal line, power line and transceiver IC for 2.4 GHz band communication system. The fabricated transceiver module has 9 layers including three inner grounds and it occupies less than $12\;mm{\times}8.0\;mm{\times}1.1\;mm$. The implemented transceiver module provides an output power of 18.1 dBm and a sensitivity of -85 dBm.