• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 추계학술대회
• /
• pp.934-939
• /
• 2004

This paper propose a study on the Feed Characteristics of Twist Friction Driver. We are using Twist Friction Driving mechanism system. The system consists of Twist Friction Driver elements such as driving shaft, driven roller, Spring for pre-load, Air bearing guide, Servo motor, and measuring devices such as Encoder of Servo motor, Laser interferometer, LVDT . The Twist Friction driver is mechanically simple and very quiet at high speed, and has low pre-load. So The Twist Friction driver can materialize an ultra precision feed-resolution. The feed characteristics of the driver is determined by slip and angular error, backlash.

• 한국전기전자재료학회논문지
• /
• 제17권2호
• /
• pp.207-211
• /
• 2004

We have performed computer simulation to obtain a globa1 optimization of power consumption and viewing angle characteristic of reflective twisted nematic (R-TN) mode liquid crystal display (LCD) with sin81e polarizer and λ/4 plate. Our studies shout that with increasing the twist angle, a steepness of reflectance-voltage curve increase, operation voltages decreases, the region where contrast ratio (CR) greater than 10 increases but the reflectance of the white state starts to decrease at above the twist angle of 75$^{\circ}$. Above the twist angle of 90$^{\circ}$, the R-TN mode LCD shows the most favorable combination of low consumption and good viewing angle characteristic.

• 천문학회지
• /
• 제32권2호
• /
• pp.137-147
• /
• 1999

Recent studies show the importance of understanding three-dimensional magnetic reconnect ion on the solar surface. For this purpose, I consider non-coplanar magnetic reconnection, a simple case of three-dimensional reconnect ion driven by a collision of two straight flux tubes which are not on the same plane initially. The relative angle e between the two tubes characterizes such reconnection, and can be regarded as a measure of magnetic shear. The observable characteristics of non-coplanar reconnection are compared between the two cases of small and large angles. An important feature of the non-coplanar reconnect ion is that magnetic twist can be produced via the re-ordering of field lines. This is a consequence of the conversion of mutual helicity into self helicities by reconnection. It is shown that the principle of energy conservation when combined with the production of magnetic twist puts a low limit on the relative angle between two flux tubes for reconnect ion to occur. I provide several observations supporting the magnetic twist generation by reconnection, and discuss its physical implications for the origin of magnetic twist on the solar surface and the problem of coronal heating.

• Journal of Genetic Medicine
• /
• 제8권2호
• /
• pp.130-134
• /
• 2011

Saethre-Chotzen 증후군은 상염색체 우성의 유전 방식을 보이는 두개골유합증후군(craniosynostosis)의 하나로, 원인 유전자는 TWIST1로 알려져 있다. Saethre-Chotzen 증후군의 임상 증상은 두개골유합증 중에서도 특히 관상봉합(coronal suture)이 편측 혹은 양측으로 조기에 폐쇄되는 것이 특징적이며, 이외에도 안검하수, 낮게 위치한 귀, 청력 소실, 손발가락의 기형 등 다양한 이상이 동반될 수 있다. 저자들은 양측성 관상봉합 두개골유합증과 특징적인 얼굴 모습, 다양한 동반 기형을 보인 두 명의 환자에서 TWIST1 유전자의 원인 돌연변이를 각각 확인하고 Saethre-Chotzen 증후군을 확진하였기에, 국내에서 처음으로 보고하는 바이다. 특히, TWIST1 유전자 분석은 관상봉합 유합증을 보이는 환자에서 질환을 확진하고, 및 환자와 가족에 대한 적절한 유전 상담을 제공하는데 유용한 검사로 생각된다.

• 한국광학회:학술대회논문집
• /
• 한국광학회 2003년도 제14회 정기총회 및 03년 동계학술발표회
• /
• pp.118-119
• /
• 2003

휴대용 통신기기의 발달로 인해 실내 및 실외 환경에서 높은 성능을 발휘하는 LCD 소자가 요구되고 있다. 후면광원을 사용하는 투과형 LCD는 실내 혹은 어두운 곳에서 높은 휘도와 명암대비비를 가지는 반면 실외나 밝은 곳에서는 높은 휘도 및 명암대비비를 보일 수 없다. 그에 반해 반사형 LCD는 주변광을 광원으로 사용하므로 실외 혹은 밝은 곳에서의 전기광학 특성이 양호한 장점이 있지만 실내 및 어두운 곳에서의 사용이 제한된다. (중략)

• 한국레이저가공학회지
• /
• 제4권3호
• /
• pp.30-39
• /
• 2001

This work was tamed out to apply a laser welding technique in joining between a Zn coated low carbon steel plate(SECC) and a free cutting carbon steel shaft(SUM24L) with or without W coating. Experiments were carried out and analysed by applying the FD(factorial design)method to obtain the optimum Laser welding condition. Optical microscopy, SEM, TEM and XRD analyses were performed in order to observe the microstructures in the fusion zone and the HAZ. Mechanical properties of the welded specimens were examined by microhardness test, tensile test and twist test. There was no flawed Zn in the fusion zone by EDS analysis. This means that during the welding process, Zn gas could be eliminated by appropriate shielding gas flow rate and butt welding gap. Ni coating itself did not influence on the tensile strength and hardness. However, twist bending strength and the weld depth of the Ni-coated free cutting carbon steel were lower as compared with those of the uncoated free cutting carbon steel. It was attributed to a lower absorbance of laser beam to the shin Ni surface. According to the results of the factorial design tests, the twist bending strength of welded specimens was primarily affected by pulse width, laser power, frequency and speed.

• Steel and Composite Structures
• /
• 제18권1호
• /
• pp.121-134
• /
• 2015

This paper is to investigate the potentials of the elastic seismic design of twisted high-rise steel diagrid frame buildings in the strong wind and moderate/low seismicity regions. First, the prototypes of high-rise steel diagrid frames with architectural plans that have a twist angle of 0 (regular-shaped), 1, and 2 degrees were designed to resist wind. Then, the effects of the twist angle on the estimated quantities and structural redundancies of the diagrid frames were examined. Second, the seismic performance of the wind-designed prototype buildings under a low seismicity was evaluated. The response spectrum analysis was conducted for the service level earthquake (SLE) having 43-year return period and the maximum considered earthquake (MCE) having 2475-year return period. The evaluation resulted that the twisted high-rise steel diagrid frames resisted the service level earthquake elastically and most of their diagrid members remained elastic even under the maximum considered earthquake.

• 한국염색가공학회지
• /
• 제12권2호
• /
• pp.89-95
• /
• 2000

Effect of twist-setting time, temperature and cylinder layer for the physical properties of the twist yarn were investigated by separated 9 layer from yarn cylinder. Obtained results were as follow. Shrinkage of the yarn in middle layer shows high value with heat-permeation and in inner's shows low value because of cylinder hardness. And then yarn thermal shrinkage in outer layers shows more or less high value because twist yarn in the outer layer sets more faster. Concerning to the difference on the yam physical properties among cylinder layers, the changes on physical properties shows significant differences from the 7th layer to the last one. Linear density, T.P.M and initial modulus decreases but snarl index increases.

• EDISON SW 활용 경진대회 논문집
• /
• 제4회(2015년)
• /
• pp.184-190
• /
• 2015

On wide variety of fields, studies on active twist control are becoming more active. For effective twist control, blades have to have low torsional stresses with high torsional deformations to the same magnitude of torque acting on its cross-section. In this study, 2D sectional analysis and 3D finite element analysis were made for 5 different blades with each having different cross - sections which have different spars. The results from 2D sectional analysis, were then put into 3D blade deformation and stress calculations which lead to analysis. Outcomes from 2D and 3D analysis, showed that on the same torque and concentrated load conditions, the blade with 'C' shaped spar was the best of all the blades which were used in this study.

• 한국전자파학회논문지
• /
• 제20권4호
• /
• pp.390-395
• /
• 2009

본 논문에서는 미앤더 스트립라인을 이용한X-대역 광대역 편파 변환기 설계 및 최적화 문제에 대해서 고찰하였다. 편파 변환기에 입사되는 편파를 수직, 수평 성분으로 분리하고 각 편파별로 등가 전송선 모델(transmission line model)을 사용하여 교차 편파 억제율과 편파 변환율을 계산하였다. 또한, 최적화된 파라미터 도출을 위해 유전 알고리즘과 particle swarm optimization에 기반한 하이브리드 알고리즘의 성능을 평가하고 설계에 적용하였다. 최적화된 편파 변환기는 X-대역(8.45$\sim$11.38 GHz)에서 -25 dB 이하의 편파 억제 성능을 보여주고 있으며, 편파 변환 손실은 0.2 dB 이하로 계산되었다. 또한, 이 결과를 상용 시뮬레이션 수치와 비교 분석하였다.