• Journal of Microbiology and Biotechnology
• /
• v.27 no.7
• /
• pp.1316-1323
• /
• 2017

Geosmin and 2-methylisoborneol (2-MIB), responsible for earthy or musty smell, are a major concern for safe drinking water supplies. This study investigated the effects of environmental factors on odorous compound production and cell growth in cyanobacterial strains. Anabaena sp. FACHB-1384, a 2-MIB producer, was sensitive to low temperature (<$20^{\circ}C$). However, geosmin producers, Anabaena sp. Chusori and Anabaena sp. NIER, were sensitive to high light intensity (>$100{\mu}mol/m^2/sec$), but not to low temperature. Geosmin concentrations increased under higher nitrate concentrations, being linearly proportional to cell density. A P-limited chemostat showed that P-stress decreased the geosmin productivity and extracellular geosmin amount per cell in Anabaena sp. NIER. However, only 2-MIB productivity was reduced in Planktothrix sp. FACHB-1374 under P-limitation. The extracellular 2-MIB amount per cell remained constant at all dilution rates. In conclusion, high light intensity and P-stress can contribute to the lower incidence of geosmin, whereas 2-MIB reduction could be attainable at a lower temperature.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.12 no.2
• /
• pp.169-177
• /
• 2024

In this paper, the effect on cement clinker and cement quality was studied to prove the effect of reducing the sintering temperature of cement clinker as a mineralizer to recycle fluorine based semiconductor sludge, an industrial by-product. In addition, a verification study was conducted to compare the properties of clinker and cement at different temperatures when natural fluorite, previously used as a mineralizer, was used. As a result of the study, semiconductor sludge showed sufficient effectiveness as a mineralizer and could replace natural fluorite, an existing mineralizer.

• Journal of Practical Agriculture & Fisheries Research
• /
• v.10 no.1
• /
• pp.77-90
• /
• 2008

This study was conducted to investigate the influence of chilling temperature and duration at different seeding stages on yield, fruit characteristics and growth of cucumber in a greenhouse. When 20-day-old cucumber were exposed to 0 and 3℃ for 10 hours, 25 and 30% reduction in the main stem elongation rate and 34 and 37% reduction in total leaf area per plant were observed. The reduction in stem elongation and total leaf area was apparently associated with the increases in chilling duration. Exposure of seedlings to 6℃ failed to causes any significant differences in growth as compared to the unchilled plants. Repeated exposure of seedlings to 3℃ chilling for 10 hours per day increased the chilling injury significantly. The seedlings exposed to low temperature for 3 consecutive days exhibited severe injury as compared to the seedlings exposed to chilling treatment only once or twice. Fruit elongation rate was inhibited by approximately 10%, such as 0.59~2.26cm/day, with chilling of 15 hours at 0℃ as compare to 0.61~2.60cm/day in the non-chilled plants. Chilling treatment at 0~3℃ for 10 hours reduced the percentage of marketable fruits by 25~26%. while it increased the percentage of severely bent fruits significantly. Total fruits yield was reduced by 15~25% in cucumber plants when the chilling treatment was given to 20-day-old seedlings and by 22~37% in 30-day-old seedlings. This shows that, Larger seedlings were more sensitive to chilling. Total yield was also influenced by the duration of chilling. Definitely, at 0℃, 5-hour chilling treatment caused 18% of reduction, 10-hour caused 30%, and 15-hour caused 36%, respectively.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.33-37
• /
• 2003

A low-power $1{\times}2$ polymeric thermo-optic switch with a trench structure is proposed and fabricated. The trench structure in the optimized region slows down the heat flow from the electrodes, which contributes to the reduction of power consumption. The temperature distribution in the polymer layers has been adjusted to increase the temperature gradient between the two arms of the Y-branch. For comparison, a $1{\times}2$ polymeric thermo-optic switch with no trench structure is fabricated together on the same substrate. In the device with a trench structure, the measured crosstalk is less than -17.0 dB for TE polarization.-15.0 dB for TM polarization. The power consumption is about 66 mW, which is 25% less than that of the device with no trench structure.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.191-192
• /
• 2023

In recent years, the use of high-strength grout has gained popularity in offshore wind power generation complexes for facility foundations and bridges. These marine wind farms require support for horizontal loads from wind and waves. To ensure the strength of the grout produced in environments similar to the actual placing site, this study investigated the curing of high-strength grout discharged through pump pressure in various environments, and examined the difference in strength according to different variables. Compressive strength measurements revealed that the core specimen collected from the bottom (3cm) and uppermost (50cm) of the specimen exhibited lower strength compared to other height specimens, while the core specimen obtained from the corner exhibited lower strength compared to the center. These findings suggest that the strength difference between the center and the corner is more pronounced when curing at low temperatures. This effect is greater than the strength reduction that typically occurs during low-temperature curing, and thus, necessitates careful attention in similar construction environments.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2001.11a
• /
• pp.55-62
• /
• 2001

An electrolytic copper rod was drawn up to $90\%$ in area reduction and annealed under various conditions. The EBSD measurement of the drawn wire showed that in the center region the <111> + <100> fiber duplex texture was dominant, while in the middle and surface regions relatively defused textures developed with a little higher density in <11w>//wire axis. The inhomogeneous texture in the deformed wire gave rise to the inhomogeneous microstructure and texture after annealing. The annealing texture could be classified into the recrystallization texture developed during low temperatures and at the early stage at a high temperature and the growth texture developed after a prolonged annealing at the high temperature. The recrystallization temperature could be explained by the strain energy release maximization model and the growth texture was discussed based on the grain boundary mobility anisotropy.

• Proceedings of the Korea Society for Energy Engineering kosee Conference
• /
• 1992.11a
• /
• pp.35-38
• /
• 1992

The feasibility of magnetohydrodynamic (MHD) Ship propulsion using superconduction magnets is reviewed in light of recent advances in high-temperature superconducting. The propulsion using a screw propeller in the noise reduction has it's own limitation. The epochal noiseless MHD propulsion method which does not have this disadvantage is studying nowadays. The subject of a marine MHD as propulsion has been examined before and was found to be interesting because of relatively low magnetic flux densities. It is demonstrated that the MHD propulsion is technically interesting with high magnetic flux density. The development of large-scale magnets using the high-temperature superconductors now under development could make it practical to construct submersibles for high-speed and silent operation.

• Macromolecular Research
• /
• v.13 no.1
• /
• pp.68-72
• /
• 2005

A low-molecular-weight poly(lactic acid) was synthesized through the condensation reaction of L-lactic acid. The effects that the catalyst and temperature have on the reaction rate were studied to determine the optimum reaction conditions. The reaction kinetics increased with temperature up to $210^{\circ}C$, but no further increase was observed above this temperature. Among a few selective catalysts, sulfuric acid was the most effective because it maximized the polymerization reaction rate. Reduction of the pressure was another important factor that enhanced this reactions kinetics.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.1
• /
• pp.10-16
• /
• 2004

The Homogeneous Charge Compression Ignition (HCCI) engine has advantage for reducing the NOx and P.M. simultaneously. Therefore, HCCI engine is receiving attention as a low emission diesel engine concept. This study was carried out to investigate the characteristics of combustion and exhaust emission for operating conditions in a direct injection type of HCCI engines such as supercharged and naturally aspirated using diesel fuel and additive. From the experimental result, we found that cool flame was always appeared and also it was difficult to control combustion characteristics by changing the injection timing in HCCI. In addition, at the lean air-fuel ratio and high speed range, it was observed that charging air pressure, additive or increasing intake air temperature is effective to increase combustion performance and reduce exhaust emission. We concluded that chemical reaction by the increasing intake air temperature or additive without physical improvement has limitation for reduction of exhaust emission.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.6
• /
• pp.727-736
• /
• 2016

Numerical simulations of n-heptane spray characteristics in a constant volume combustion chamber under diesel engine like conditions with increasing ambient gas density ($14.8-142kg/m^3$) and ambient temperature (800-1000 K) respectively were performed to understand the non-vaporizing and vaporizing spray behavior. The effect of fuel temperature (ranging 273-313 K) on spray characteristics was also simulated. In this simulation, spray modeling was implemented into ANSYS FORTE where the initial spray conditions at the nozzle exit and droplet breakups were determined through nozzle flow model and Kelvin-Helmholtz/Rayleigh-Taylor (KH-RT) model. Simulation results were compared with experimentally obtained spray tip penetration result to examine the accuracy. In case of non-vaporizing condition, simulation results show that with an increment of the magnitude of ambient gas density and pressure, the vapor penetration length, liquid penetration length and droplet mass decreases. On the other hand vapor penetration, liquid penetration and droplet mass increases with the increase of ambient temperature at the vaporizing condition. In case of lower injection pressure, vapor tip penetration and droplet mass are increased with a reduction in fuel temperature under the low ambient temperature and pressure.