• 한국인터넷방송통신학회논문지
• /
• 제17권3호
• /
• pp.137-143
• /
• 2017

IoT 카스토퍼 기반의 스마트주차 안내 시스템을 제안하고 구현하였다. IoT 센서 모듈을 내장한 카스토퍼 감지센서는 기존의 매립형 주차센서에 비해 시공이 용이한 장점을 가진다. 순차적 점대점 통신을 통해 카스토퍼에서 전송된 주차상태 데이터는 IoT 게이트웨이를 통해 웹서버에 저장되고, 스마트기기의 안드로이드 앱을 통해 원격으로 주차공간을 확인할 수 있다. 배터리로 구동되는 IoT 카스토퍼는 소모 전력을 줄이기 위해 워치독 타이머와 연동한 액티브/슬립 싸이클 방식을 사용한다. 카스토퍼의 소모전력은 액티브 모드와 슬립 모드에서 각각 80mW와 25mW로 측정되었다. 슬립 모드에서 발생하는 전력 소모를 최소화 할 수 있는 초저전력 IoT 센서모듈 구조를 제안하였다. 실제 주차장에서 구현된 시스템의 동작을 검증하였다.

• 전자공학회논문지A
• /
• 제31A권3호
• /
• pp.18-27
• /
• 1994

An 8-bit 2-stage pipelined current mode A/D converter is designed with a new architecture, where the wideband track-and-hold amplifiers which have 2 integrators in parallel sample input signal twice per clock cycle. The conversion speed of the A-D converter is two times faster than that of conventional pipelined method. The converter is designed to be operated at the power supply voltage of 3.3V with the input dynamic range of 0-256$\mu$A. HSPICE simulation results show the performance of up to 55Msamples/s and power consumption of 150mW with the parameters of ISRC $1.5\mu$m BICMOS process. The chip area is 3${\times}4mm^{2}$.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1997년도 춘계학술발표회논문집(1)
• /
• pp.458-463
• /
• 1997

A transient natural circulation behavior during a LOCA at hot-standby operation is evaluated for YGN Units 3/4. The plant initial condition is determined within the EOP limitation as suitable to hot-standby mode and the transient scenario is prepared as relevant to evaluation of transient natural circulation. A 0.4% cold leg break with loss of off-site power is calculated with RELAP5/MOD3.2, whose predictability has been verified for SBLOCA natural circulation test, S-NC-8B. Through one hour transient analysis, it is found that the plant has its own decay heat removal capability by natural circulation following a LOCA, at hot-standby mode. Additional calculation is performed to investigate an effect of HPSI flow on natural circulation.

• 전력전자학회논문지
• /
• 제2권3호
• /
• pp.37-43
• /
• 1997

2상 하이브리드 스텝모터를 미세스텝으로 제어하면 저속에서도 부드럽게 회전하고, 스텝 분해능을 높일 수 있으며, 공진으로 인한 바람직하지 못한 현상들을 제거할 수 있다. 본 논문에서는 고성능 미세스텝 구동회로를 개발하였다. 본 논문에서 개발한 미세스텝 구동회로는 2상 하이브리드 스텝모터의 1회전스텝(1.8도)을 128 미세스텝으로 구동할 수 있는 위치 분해능을 가지며 스텝모터를 장시간 구동할 때 발생되는 열로 인한 문제점을 줄이기 위한 전류 절약 동작모드를 지원한다.

• 조명전기설비학회논문지
• /
• 제27권12호
• /
• pp.63-73
• /
• 2013

The parameters of electromechanical modes offer considerable insight into the dynamic stability properties of a power system. This paper presents a results of a LFO(low-frequency oscillation) based on the time-synchronized signals measured by synchrophasor in the rolling blackout. Spectral analysis was performed, and critical parameters were estimated using the data acquired from synchrophasors installed in the KEPCO system. As significant modes, a 0.68 Hz oscillation mode that occurred prior to the forced load shedding in the rolling blackout was estimated. Such an oscillation mode can cause an uncontrollable blackout. Therefore, the system should be operated so that significant oscillation modes are not activated. This results can serve as a reference in the future for reliable system operation in the event of a similar blackout.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2002년도 전력전자학술대회 논문집
• /
• pp.91-94
• /
• 2002

This paper presents a novel active common-mode EMI filter for the PWM inverter application. The proposed filter is based on the current sensing and compensation circuit and it utilizes a fast transistor amplifier for the current compensation. The amplifier utilizes an isolated low-voltage dc power supply for its biasing and it is possible to construct the active filter independent of the source voltage of the equipment. Thus the proposed active filter can be used in any application regardless of its working voltage. The effectiveness of the proposed circuit is verified by experimental results.

• Journal of Power Electronics
• /
• 제11권4호
• /
• pp.512-519
• /
• 2011

This paper gives a detailed analysis of the direct torque control (DTC) strategy in a five-level drive and proposes a 24-sector switching table. The known problems in low-voltage drives such as bearings currents and an overvoltage phenomenon which leads to premature failure are reviewed and the occurrence of these problems in medium voltage drives has been investigated. Then a solutions to these problems is presented and the switching table to deal with these problems is modified. Simulation and experimental results on a 3kVA prototype confirm the proposed solution. In implementing the above strategy a TMS320F2812 is used.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 전력전자학술대회 논문집
• /
• pp.308-311
• /
• 2001

Most of the battery charger for electric powered forklift truck are controlled by the method of 3-phased constant current and constant voltage. However, these chargers have several disadvantages like a large charger capacity, and a short battery life time. This paper presents a digital type battery charger based on multi-mode control adding a constant power control and several assistant controls in the conventional control. The whole control system is performed by a low cost one-chip micro-controller and completely digitize. So we can get a high precision control and a good reliability.

• 한국전기전자재료학회논문지
• /
• 제22권10호
• /
• pp.897-903
• /
• 2009

We have designed the backward wave oscillator. A power-pulsed generator oscillated at 24 GHz has higher frequency than current one. It is very inportant to prevent microwave from going into the beam diode, since intence microwave will harmfully affect beam generation. Due to the axial mode operation, there exist a critial value of beam energy for the oscillation. By changing the condition at the SWS end, an enhanced performance of the K-band oversized BWO is observed in a low magnetic field region about 0.8T.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2010년도 추계학술대회
• /
• pp.173-174
• /
• 2010

In this paper, authors propose a new buck-boost converter of discontinuous conduction mode (DCM) added electric isolation. The proposed converter with DCM eliminates the complicated circuit control requirement and reduces the size of components. The general converters of high efficiency are made that the power loss of the used switching devices is minimized. To achieve the soft switching operation of the used control switches, the proposed converter uses a lossless snubber capacitor. The proposed converter achieves the soft-switching for all switching devices without increasing their voltage and current stresses. The result is that the switching loss is very low and the efficiency of converter is high. The soft switching operation of the proposed converter is verified by digital simulation and experimental results.