• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.2 no.1
• /
• pp.19-31
• /
• 1982

The purpose of the research is to investigate the applicability of the filter activated sludge process for the treatment of toxic phenolic wastewaters. The experiment for the research was carried out by continuously feeding synthetic phenol wastewater for four periods, and the results show that a synthetic fiber filter is an adequate material for filter activated sludge process when taking consideration of durability, SS removal efficiency and wastewater permeability. The permeability of the filter sharply decreases when the temperature of the reactor is below $10{\sim}15^{\circ}C$ for a long period. In filter activated sludge process, even under high volumetric loading conditions, high phenol removal efficiencies can be attained due to the high microbial sludge concentration in the reactor and consequently low F/M ratio. In this research, the effluent phenol concentration were checked to be below $0.1mg/{\ell}$ at the influent phenol concentrations of $63{\sim}468mg/{\ell}$. During the research very low microbial yield coefficients, 0.035~0.160 kg SS/kg COD removed, were observed and the temperature coefficient for aerobic sludge digestion was measured to be 1.021.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.6 s.134
• /
• pp.55-62
• /
• 2005

This study was conducted to evaluate the application of a bio-composite made by the addition recycled fiber board flour as filler. Recycled fiber board (high density fiber board, HDF) flour was added to polyolefin polymer low density polyethylene (LDPE) and polypropylene (PP) for the preparation of bio-composite materials. The mechanical properties and processability of the recycled HDF flour filled LDPE and recycled HDF flour filled PP bio-composites were then measured and compared to those of wood flour (WF) and rice-husk flour (RHF) filled LDPE and PP bio-composites, respectively. The tensile and impact strengths of the recycled HDF flour filled LDPE and PP bio-composites had similar mechanical properties to those of the WF and RHF filled LDPE and PP bio-composites. To measure the processability, torques of the bio-composites were also measured. The torques of the HDF flour filled LDPE and PP bio-composites were lower than those of the WF and RHF filled polyolefin (PP and LDPE) bio-composites with a filler loading of 30 wt.%. This result showed definite processability, which was not related with the distribution of the particle size of the material added. The recycled fiber board flour filled bio-composites showed applicability as substitutes for the bio-composites currently used in the bio-composites industry.

• Journal of the Korean Vacuum Society
• /
• v.16 no.4
• /
• pp.244-249
• /
• 2007

Deadweight piston gauge have been widely used as a fundamental instrument of precise pressure measurement because they are robust, accurate, potable, convenient to use and are able to realize the definition of pressure as farce per unit area. Basically, a deadweight piston gauge consists of a piston mounted vertically in a close-fitting cylinder filled with a gas and weights of known mass values. The pressure to be measured is applied to the base of the piston generating an upward vertical force, and is balanced by the downward gravitational force generated by weights. These instruments can be used to measure pressures above 10 kPa because of tare weights including piston. However, using a variable bell-jar pressure method and a newly developed weight loading device we can extend the application range of deadweight piston gauge to lower pressures. In this paper, we present the practical calibration results for two CDGs(Capacitance diaphragm gauge, MKS) with full-scale ranges of 1.33 kPa and 13.3 kPa, respectively.

• Korean Journal of Ecology and Environment
• /
• v.39 no.4 s.118
• /
• pp.481-488
• /
• 2006

The field scale experiment was performed to examine the performance of the constructed wetland for nonpoint source (NPS) pollution loading reduction. Four sets (0.88 ha each) of wetland and pond system were used. After three growing seasons of the wetland construction, plant coverage increased to about 90% even without plantation from bare soil surfaces at the initial stage. During the start up period of constructed wetlands, lower water levels should be maintained to avoid flooding newly plants, if wetland plants are to start from germinating seeds. The average removal rate of $BOD_5$, TSS, T-N and T-P during the first two years was 5.6%, 46.6%, 45.7%, and 54.8%, respectively. The $BOD_5$ removal rate was low and it might be attributed to the low influent concentration. The early stage of wetland performance demonstrated the effectiveness of water quality improvement and was satisfactory for treating polluted stream waters. From the first-order analysis, T-P was virtually not temperature dependent, and $BOD_5$ and TSS were more temperature dependent than T-N. A pond-wetland system was more effective than a wetland-pond or a wetland alone system in water quality improvement, particularly to reduce T-P. Overall, the wetland system was found to be an adequate alternative for treating a polluted stream water with stable removal efficiency and recommended as a NPS control measures.

• Restorative Dentistry and Endodontics
• /
• v.14 no.2
• /
• pp.38-48
• /
• 1989

The purpose of this study was to investigate the proper consistency of root canal sealer needed in obtaining an efficient canal obturation in injection-thermoplasticized low-temperature ($70^{\circ}C$) gutta-percha method. The sealer was made by incorporating zinc oxide powder into $0.5m{\ell}$ of eugenol and then the $0.5m{\ell}$ of mixture slurry was placed between two flat glass plates. The consistency was determined by measuring the degree of spread of the slurry at loading the 120gm of weight from the top plate. The sealer was prepared according to P/L ratio corresponding to the acquired consistency of 65.45mm, 46.80mm, 28.95mm and 22.60mm. The distal roots were obtained by cutting off from 125 extracted human lower molars and the root canals were prepared by using step-back method. The prepared canals were coated with the sealers on their walls and obturated by using the injection-thermoplasticized low-temperature ($70^{\circ}C$) gutta-percha method. All specimens were immersed in 2% methylene blue dye solution for 48 hours at $37^{\circ}C$. Calipers was used to measured the dye penetration into the root canals from apical constrictions. The results were as follows : The canals obturated without sealer showed significantly more leakage than the canals obturated with sealer. Within the consistency from 65.45mm to 22.60mm, the sealer of 65.45mm appeared significantly better than that of 28.95mm and 22.60mm in the canals obturated by injection-thermoplasticized gutta-percha method, and better than that of 46.80mm without statistical significance.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.43 no.7
• /
• pp.1095-1103
• /
• 2014

A packaging and distribution system for transferring individual live squids at low temperature was developed and compared to a conventional bulk container system. Ten live squids in individual packages were stored in a large container at low temperature ($0{\sim}10^{\circ}C$). Live squids in individual packages at $6^{\circ}C$ showed a survival rate of 84% up to 72 hours, after which the survival rate decreased. However, the survival rate remained at 60% up to 120 hours. Further, the squids survived up to a maximum of 7 days. Optimum temperature was $5^{\circ}C$, and the survival rate of the packages was 70% when stored at $5^{\circ}C$ for 96 hours. A distribution test was carried out using a refrigerator truck at $5^{\circ}C$, and the results showed a 100% survival rate up to 16 hours and over 90% survival rate after 20 hours. A rectangular container was the most favorable when loading the container into the refrigerator truck. In testing the required volume of supplied seawater, 100% survival rate was observed over 15 hours with 20 L of sea water or more. Therefore, a single squid needed 2 L of seawater. After refrigerator truck transportation, optimum temperature for fish tank storage was $5^{\circ}C$, at which the survival rate was over 90% up to 72 hours. Using a refrigerator truck at $5^{\circ}C$, live squids survived up to 7 days, maintaining marketability.

• Elastomers and Composites
• /
• v.46 no.3
• /
• pp.218-222
• /
• 2011

The effect of cycled temperature change on the mechanical properties of wood flour(50 wt.% and 70 wt.%) polypropylene WPC(Wood Plastic Composites) was investigated in this study. Flexural modulus and flexural strength of the WPC showed a decrease due to the degradation of interfacial adhesion between polymer matrix and wood flour by the freeze-thaw test regardless of the cycled number. At the higher loading level of wood flour, the reduction of the flexural modulus was remarkable. After the cycled heat-freeze test, it was found that the flexural modulus and flexural strength of the WPC were lower at the high temperature ($60^{\circ}C$) and higher at the low temperature ($-20^{\circ}C$). At the low temperature ($-20^{\circ}C$) which is below glass transition temperature of polypropylene ($-10^{\circ}C$), WPC is in a glassy state which brings about the high stiffness and strength. At the high temperature ($60^{\circ}C$), the flexural modulus and flexural strength of the WPC with 50 wt.% wood flour were lower because of the increase of polymer ductility.

• Journal of the Society of Naval Architects of Korea
• /
• v.39 no.3
• /
• pp.57-63
• /
• 2002

This paper describes a control algorithm for the buffer of a deep-sea mining system, in which the buffer is connected to a long slender pipe and then to a surface ship on one end, and to a collector on sea floor through a flexible hose on the other end. A mathematical modeling is established for designing the controller for buffer thrusters, in which the dynamic response of the long pipe is taken into account based on the mode superposition method. The fluid loading acting on the pipe is estimated by using Morison's formula. For simplicity, the surface ship is assumed to be kept stationary, the reaction from the flexible hose is ignored and only the lateral motions are considered. In order to guide the buffer to react only to the low-frequency motion of the surface vessel, the FIR digital filter is introduced to a PID-based controller It can be shown numerically that the high frequency component of the ship's motion can be effectively filtered out by using the FIR low pass filter.

• Polymer(Korea)
• /
• v.33 no.4
• /
• pp.389-395
• /
• 2009

To develop the carrier of hydrophobic antifungal agents based on low molecular weight water-soluble chitosan (LMWSC), LMWSC was chemically modified with deoxycholic acid (DA) which is one of the bile acid as a hydrophobic group. The nanoparticles (WSCDA) using DA conjugated LMWSC were characterized using dynamic light scattering (DLS) and transmittance electron microscope (TEM). The particle size of WSCDA ranged from 250 to 350 nm and increased with the number of DA substitution. The loaded itraconazole as an antifungal agent WSCDA nanoparticles (WSCDA-ITCN) were prepared by solvent evaporation method. The drug content and the loading efficiency were investigated approximately $9{\sim}10%$ and $61{\sim}68%$ by UV spectrophotometer, respectively. The release of drug from nanoparticles was slow and showed sustained release characteristics. Based on the results of release study that the higher DA contents in WSCDA, the slower the releasing rate, the WSCDA-ITCN could be used as an excellent antifungal agent.

• Journal of the Korean Society of Surveying, Geodesy, Photogrammetry and Cartography
• /
• v.34 no.5
• /
• pp.535-544
• /
• 2016

Even though existing methods for orthophoto production using expensive aircraft are effective in large areas, they are drawbacks when dealing with renew quickly according to geographic features. But, as UAV(Unmanned Aerial Vehicle) technology has advanced rapidly, and also by loading sensors such as GPS and IMU, they are evaluates that these UAV and sensor technology can substitute expensive traditional aerial photogrammetry. Orthophoto production by using UAV has advantages that spatial information of small area can be updated quickly. But in the case of existing researches, images of same altitude are used in orthophoto generation, they are drawbacks about repetition of data and renewal of data. In this study, we targeted about small slope area, and by using low-end UAV, generated orthophoto and DEM(Digital Elevation Model) through different altitudinal images. The RMSE of the check points is σ_h = 0.023m on a horizontal plane and σ_v = 0.049m on a vertical plane. This maximum value and mean RMSE are in accordance with the working rule agreement for the aerial photogrammetry of the National Geographic Information Institute(NGII) on a 1/500 scale digital map. This paper suggests that generate orthophoto of high accuracy using a different altitude images. Reducing the repetition of data through images of different altitude and provide the informations about the spatial information quickly.