• Horticultural Science & Technology
• /
• v.32 no.5
• /
• pp.590-599
• /
• 2014

This study was conducted to compare the cold tolerance of seven ground cover species, Orostachys japonica, Sedum oryzifolium, S. kamtschaticum 'SG1', S. reflexum, S. rupestre 'Blue Spruce', S. spurium 'Green Mental', and S. takesimense, which have been used for green roof and wall systems in Korea. Plants were grown in 10-cm pots and 1 g of tissues at stem-end and crown of each species were kept under either light or dark condition, respectively. For cold tolerance tests, plants were initially left at $4^{\circ}C$ and linearly cooled to 0, -4, -8, -12, -16, and $-20^{\circ}C$ at $-2^{\circ}C{\cdot}h^{-1}$ rate. Low temperature injury and regrowth rates were visually evaluated and assessed by image analysis, respectively. The lethal temperature ($LT_{50}$) of plant species was determined using electrolyte leakage measurements. S. reflexum was the most cold tolerant, showing the most survival at $-16^{\circ}C$, whereas S. oryzifolium and S. takesimense showed low temperature injury at $-8^{\circ}C$. Similar results were found with electrolyte leakage measurements at the stem end. For each species, the crown (Mean $LT_{50}:\;-12.15^{\circ}C$) was more cold tolerant than the stem end (Mean $LT_{50}:\;-10.47^{\circ}C$). In conclusion, S. reflexum and S. rupestre 'Blue Spruce' are recommended for planting in the central region of Korea during late fall and early winter, as they were more cold tolerant and showed more vigorous regrowth than the other tested plant species.

• Restorative Dentistry and Endodontics
• /
• v.26 no.4
• /
• pp.263-272
• /
• 2001

The aim of this study was to investigate the influence of four different light curing modes on the marginal leakage of Class V composite resin restoration. Eighty extracted human premolars were used. Wedge-shaped class Y cavities were prepared on the buccal surface of the tooth with high-speed diamond bur without bevel. The cavities were positioned half of the cavity above and half beyond the cemento-enamel junction. The depth, height, and width of the cavity were 2 mm, 3 mm and 2 mm respectively. The specimens were divided into 4 groups of 20 teeth each. All the specimen cavities were treated with Prime & Bond$^{R}$ NT dental adhesive system (Dentsply DeTrey GmbH, Germany) according to the manufacturer's instructions and cured for 10 seconds except group VI which were cured for 3 seconds. All the cavities were restored with resin composite Spectrum$^{TM}$ TPH A2 (Dentsply DeTrey GmbH, Germany) in a bulk. Resin composites were light-cured under 4 different modes. A regular intensity group (600 mW/${cm}^2$, group I) was irradiated for 30 s, a low intensity group (300 mW/${cm}^2$, group II) for 60 s and a ultra-high intensity group (1930 mW/${cm}^2$, group IV) for 3 s. A pulse-delay group (group III) was irradiated with 400 mW/${cm}^2$ for 2 s followed by 800 mW/${cm}^2$ for 10 s after 5 minutes delay. The Spectrum$^{TM}$ 800 (Dentsply DeTrey GmbH, Germany) light-curing units were used for groups I, II and III and Apollo 95E (DMD, U.S.A.) was used for group IV. The composite resin specimens were finished and polished immediately after light curing except group III which were finished and polished during delaying time. Specimens were stored in a physiologic saline solution at 37$^{\circ}C$ for 24 hours. After thermocycling (500$\times$, 5-55$^{\circ}C$), all teeth were covered with nail varnish up to 0.5 mm from the margins of the restorations, immersed in 37$^{\circ}C$, 2% methylene blue solution for 24 hours, and rinsed with tap water for 24 hours. After embedding in clear resin, the specimens were sectioned with a water-cooled diamond saw (Isomet$^{TM}$, Buehler Co., Lake Bluff, IL, U.S.A.) along the longitudinal axis of the tooth so as to pass the center of the restorations. The cut surfaces were examined under a stereomicroscope (SZ-PT Olympus, Japan) at ${\times}$25 magnification, and the images were captured with a CCD camera (GP-KR222, Panasonic, Japan) and stored in a computer with Studio Grabber program. Dye penetration depth at the restoration/dentin and the restoration/enamel interfaces was measured as a rate of the entire depth of the restoration using a software (Scion image, Scion Corp., U.S.A.) The data were analysed statistically using One-way ANOVA and Tukey's method. The results were as follows : 1. Pulse-Delay group did not show any significant difference in dye penetration rate from other groups at enamel and dentin margins (p>0.05) 2. At dentin margin, ultra-high intensity group showed significantly higher dye penetration rate than both regular intensity group and low intensity group (p<0.05). 3. At enamel margin, there were no statistically significant difference among four groups (p>0.05). 4. Dentin margin showed significantly higher dye penetration rate than enamel margin in all groups (p<0.05).

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.40 no.4
• /
• pp.409-415
• /
• 2020

Low-flow mortar injection method grouting technology was selected and the traffic area was preserved as much as possible in order to secure safety for road traffic when the outflow and subsidence of landfill occurred due to ground-water, and etc. In particular, the current existing method was newly improved since there are risks of damage such as hydraulic fracturing at the lower part of the road, spilling of soil particles on steep slopes, and bumps on the road due to excessive injection pressure during construction. This study was carried out at the site of reinforcement work on the road as a maintenance work for the danger zone for collapse of the steep slope of the 00 hill, which was ordered from the 00 city 00 province. The improved low-flow mortar type grouting method adopted a new automated grouting management system and especially, it composites the method for grouting conditions decision by high-pressure pre-grouting test and injection technology by AGS-controlled and studied about grouting effect analysis by using new technology. By applying the improved low-flow mortar type grouting method, it was possible to lay the groundwork for road maintenance work such as the prevention of subsidence of old roads, uneven subsidence of buildings and civil engineering structures, and of soil leakage of ground-water spills. Furthermore, the possibility of application on future grouting work not only for just construction that prevents subsidence of old roads but also for various buildings and civil engineering structures such as railroads, subways, bridges, underground structures, and boulder stone and limestone areas was confirmed.

• Journal of Bio-Environment Control
• /
• v.14 no.3
• /
• pp.218-231
• /
• 2005

This paper reviews the engineering approach needed to support humans during their long-term missions in space. This approach includes closed plant production systems under microgravity or low pressure, mass recycling, air revitalization, water purification, waste management, elimination of trace contaminants, lighting, and nutrient delivery systems in controlled ecological life support system (CELSS). Requirements of crops f3r space use are high production, edibility, digestibility, many culinary uses, capability of automation, short stems, and high transpiration. Low pressure on Mars is considered to be a major obstacle for the design of greenhouses fer crop production. However interest in Mars inflatable greenhouse applicable to planetary surface has increased. Structure, internal pressure, material, method of lighting, and shielding are principal design parameters for the inflatable greenhouse. The inflatable greenhouse operating at low pressure can reduce the structural mass and atmosphere leakage rate. Plants growing at reduced pressure show an increasing transpiration rates and a high water loss. Vapor pressure increases as moisture is added to the air through transpiration or evaporation from leaks in the hydroponic system. Fluctuations in vapor pressure will significantly influence total pressure in a closed system. Thus hydroponic systems should be as tight as possible to reduce the quantity of water that evaporates from leaks. And the environmental control system to maintain high relative humidity at low pressure should be developed. The essence of technologies associated with CELSS can support human lift even at extremely harsh conditions such as in deserts, polar regions, and under the ocean on Earth as well as in space.

• Journal of Korean Society of Forest Science
• /
• v.111 no.2
• /
• pp.251-262
• /
• 2022

We selected a cold-tolerant tea tree (Camellia sinensis L.) through reliable evaluation using a number of cold-tolerance indicators targeting tea tree cultivars such as "Chamnok," "Bohyang," "Sangnok," and "Myungnok" in response to climate change. We conducted a low-temperature damage investigation, "Chamnok" and "Bohyang" were damaged investigated with small amounts of green and bright green. "Sangnok" and "Myungnok" were damaged investigated red and dark red at -10℃. The extent of electrolyte leakage increased as the treatment temperature decreased in all cultivars. We predicted lethal temperatures through non-linear regression analysis, finding relatively higher tolerance to low temperature in "Chamnok" (-9.344℃) and "Bohyang" (- 8.883℃) than that in "Myungnok" (-8.092 ℃) and"Sangnok" (-7.632℃). "Bohyang" showed higher levels of antioxidant activity compared to other cultivars. The lipid peroxidation reaction revealed that "Sangnok" and "Myungnok" had higher MDA content than that of other cultivars when treated at low temperatures. Consequently, predictions of the lethal temperature through non-linear regression analysis of "Chamnok" and "Bohyang" were consistent with their tolerance to low-temperature damage, and antioxidant activity and lipid peroxidation reactions were likewise consistent. The results of this study can be used not only for evaluation and selection of cold-tolerance of tea trees in response to climate change, but also in the cultivation of cold-tolerant plants.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.351-358
• /
• 2006

In this paper, the electrical characteristics of the contactless transformer is presented using the conventional coupled inductor theory. Compared with the conventional transformer, the contactless transformer has a large airgap, long primary wire and multi-secondary wire. As such, the contactless transformer has a large leakage inductance, small magnetizing inductance and poor coupling coefficient. Therefore, large magnetizing currents flow through the entire primary system due to small magnetizing inductance, resulting in low overall system efficiency. In high power applications, the contactless transformer is so bulky and heavy that it needs to be split by some light and small transformers. So, the contactless transformer needs several small transformer modules that are connected in series or parallel to transfer the primary power to the secondary one. This paper shows the analysis and measurement results of each contactless transformer module and comparison results between the series- and parallel-connection of the contactless transformer. The results are verified on the simulation based on the theoretical analysis and the 30kW experimental prototype.

• Journal of electromagnetic engineering and science
• /
• v.5 no.3
• /
• pp.140-145
• /
• 2005

In this paper, an experimental investigation for return loss and a software-based prediction for interference level of single-packaged filtering antenna composed of dielectric waveguide filter and PCB(Printed Circuit Board) slot antenna in transceiver module have been carried out with several different feeding structures in millimeter-wave regime. The implementation and embedding method of the existing air-filled waveguide filters working at millimeter-wave frequency on general PCB substrate have been described. In a view of the implementation of each components, the dielectric waveguide embedded in PCB and LTCC(Low Temparature Co-fired Ceramic) substrates has employed the via fences as a replacement with side walls and common ground plane to prevent energy leakage. The characteristics of several prototypes of filtering antenna embedded in PCB substrate are considered by comparing the wideband and transmission characteristics as a function of bent angle of transmission line connecting two components. In addition, as an essential to the packaging of transceiver module working at millimeter-wave, miniaturization technology maintaining the performances of independent components and the important problems caused by integrating and connecting the different components in different layers are described in this paper.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.923-925
• /
• 2002

The existing contactless inductive coupler has many problems because of its large volume and high level of exciting current, so a new contactless inductive coupler is being required under the circumstances and the load requirement. For a contactless inductive coupler in the manufacturing equipment of semiconductor, the coupler's efficiency is low because of its small magnetic inductance and large leakage inductance. Moreover, the high frequency switching to increase energy density per unit volume increases the iron loss and the eddy current loss, so it must be considered deeply when selecting core materials. Therefore, this paper presents core materials and shape to improve the performance of the contactless inductive coupler according to the coil positions.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1697-1699
• /
• 2004

In this investigation, we have studied the diffusion of the $Cu^+$ ion in the Cu/Ta/SiOCH/Si and Cu/Ta/$SiO_2$/Si MIS-C structure. The Cu ions diffusion into the Ta barrier and SiOCH was examined by shift in flatband voltage of capacitance-voltage measurement and leakage current of current-voltage measurement. These evalution indicated that $Cu^+$ ion diffusion rate in Ta/SiOCH is considerably lower then the Ta/$SiO_2$ structure. And diffusion barrier Ta(50[nm]) is useful barrier against $Cu^+$ ion diffusion up to 450$^{\circ}C$.

• International Journal of Fuzzy Logic and Intelligent Systems
• /
• v.14 no.2
• /
• pp.113-121
• /
• 2014

A subsea oil production system must be safely operated for 20-30 years after being installed. Because of the severe conditions of the subsea environment, such as extreme high pressure, low visibility, the possibility of unexpected impact by any object, and corrosion by seawater, subsea oil production systems should be monitored by subsea data logger systems and remotely operated vehicles to check for abnormal vibration and leakage to prevent a catastrophic accident. Because of the severity of subsea environmental conditions and the dominance of a few companies in the market, many people have thought that it would be difficult to develop a subsea data logger system. The primary objectives of the study described in this paper were to analyze existing subsea data logger systems to establish the requirements for a subsea data logger system, implement a prototype subsea data logger system, and conduct a test of the prototype subsea data logger system.