• 한국지반환경공학회 논문집
• /
• 제18권9호
• /
• pp.5-9
• /
• 2017

일반적인 지하수에 대해서는 지반공학적 방법((1)지반을 굴착한 후 지중연속벽체의 육안 확인, (2)벽체의 코아 채취 후 일축압축강도시험, (3)벽체 코아 채취 시 현장 투수시험)으로 주열식 지중연속벽체의 차수효과를 확인할 수 있다. 그러나, 폐기물 매립장내에서 발생하는 침출수와 같은 고농도 오염수 유출이나 침투의 차단에 대해서는 주변 지하수 등을 대상으로 현장에서 pH, 수온, 염분 농도 등을 측정하고 이들의 성분시험을 실시하여 기본 성분 및 성분비 등의 특성을 분석한 후 일치성 유사성을 판정하며, GC-MS를 이용하여서는 이들 시료수의 크로마토그램에 대한 피크의 높고 낮음의 차이 등 전반적인 분포패턴을 비교하여 간편하게 유사성 판정을 추가적으로 실시함으로써 객관성 있게 주열식 지중연속벽체의 차수효과를 확인하여야 한다.

• Journal of Industrial and Engineering Chemistry
• /
• 제68권
• /
• pp.117-123
• /
• 2018

Recently, aqueous method has attracted lots of attention because it enables the solution-processed metal oxide thin film with high electrical properties in low temperature fabrication condition to various flexible devices. Focusing the development of aqueous route, many researchers are only focused on metal oxide materials. However, for expansive application of the aqueous-based metal oxide films, the systematic study of performance change with process variables for the development of aqueous-based metal oxide insulator film is urgently required. Here, we propose importance of process variables to achieve high electrical-performance metal oxide insulator based on the aqueous method. We found that the significant process variables including precursor solution temperature and humidity during the spincoating process strongly affect chemical, physical, and electrical properties of $AlO_x$ insulators. Through the optimization of significant variables in process, an $AlO_x$ insulator with a leakage current value approximately $10^5$ times smaller and a breakdown voltage value approximately 2-3 times greater than un-optimized $AlO_x$ was realized. Finally, by introducing the optimized $AlO_x$ insulators to solutionprocessed $InO_x$ TFTs, we successfully achieved $InO_x/AlO_x$ TFTs with remarkably high average field-effect mobility of ${\sim}52cm^2V^{-1}\;s^{-1}$ and on/off current ratio of 106 at fabrication temperature of $250^{\circ}C$.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2008년 영문 학술대회
• /
• pp.743-750
• /
• 2008

Asymmetric tip clearance in an axial compressor induces pressure and velocity redistributions along the circumferential direction in an axial compressor. This paper presents the mechanism of the flow redistribution due to the asymmetric tip clearance with a simple numerical modeling. The flow field of a rotor of an axial compressor is predicted when an asymmetric tip clearance occurs along the circumferential direction. The modeling results are supported by CFD results not only to validate the present modeling but also to investigate more detailed flow fields. Asymmetric tip clearance makes local flow area and resultant axial velocity vary along the circumferential direction. This flow redistribution 'seed' results in a different flow patterns according to the flow coefficient. Flow field redistribution patterns are largely dependent on the local tip clearance performance at low flow coefficients. However, the contribution of the main flow region becomes dominant while the tip clearance effect becomes weak as the flow coefficient increases. The flow field redistribution pattern becomes noticeably strong if a blockage effect is involved when the flow coefficient increases. The relative flow angle at the small clearance region decreases which result in a negative incidence angle at the high flow coefficient. It causes a recirculation region at the blade pressure surface which results in the flow blockage. It promotes the strength of the flow field redistribution at the rotor outlet. These flow pattern changes have an effect on the blade loading perturbations. The integration of blade loading perturbation from control volume analysis of the circumferential momentum leads to well-known Alford's force. Alford's force is always negative when the flow blockage effects are excluded. However when the flow blockage effect is incorporated into the modeling, main flow effects on the flow redistribution is also reflected on the Alford's force at the high flow coefficient. Alford's force steeply increases as the flow coefficient increases, because of the tip leakage suppression and strong flow redistribution. The predicted results are well agreed to CFD results by Kang and Kang(2006).

• Journal of Magnetics
• /
• 제16권1호
• /
• pp.36-41
• /
• 2011

If gas is leaking out of gas pipelines, it could cause a huge explosion. Accordingly, it is important to ensure the integrity of gas pipelines. Traditionally, over the years, gas-operating companies have used the ILI system, which is based on axial magnetic flux leakage (MFL), to inspect the gas pipelines. Relatively, there is a low probability of detection (POD) for the axial defects with the axial MFL-based ILI. To prevent the buried pipeline from corrosion, it requires a protective coating. In addition to the potential damage to the coating by environmental factors and external forces, there could be defects on the damaged coating area. Thus, it is essential that nondestructive evaluation methods for detecting axial defects (axial cracks, axial groove) and damaged coating be developed. In this study, an electromagnetic acoustic transducer (EMAT) sensor was designed and fabricated for detecting axial defects and coating disbondment. In order to validate the performances of the developed EMAT sensor, experiments were performed with specimens from axial cracks, axial grooves, and coating disbondment. The experimental results showed that the developed EMAT sensor could detect not only the axial cracks (minimum 5% depth of wall thickness) and axial grooves (minimum 10% depth of wall thickness), but also the coating disbondment.

• Journal of Microbiology and Biotechnology
• /
• 제31권6호
• /
• pp.890-901
• /
• 2021

The 11α-hydroxylation of canrenone can be catalyzed by Aspergillus ochraceus in bioreactors, where the geometry of the impeller greatly influences the biotransformation. In this study, the effects of the blade number and impeller diameter of a Rushton turbine on the 11α-hydroxylation of canrenone were considered. The results of fermentation experiments using a 50 mm four-blade impeller showed that 3.40% and 11.43% increases in the conversion ratio were achieved by increasing the blade number and impeller diameter, respectively. However, with an impeller diameter of 60 mm, the conversion ratio with a six-blade impeller was 14.42% lower than that with a four-blade impeller. Data from cold model experiments with a large-diameter six-blade impeller indicated that the serious leakage of inclusions and a 22.08% enzyme activity retention led to a low conversion ratio. Numerical simulations suggested that there was good gas distribution and high fluid flow velocity when the fluid was stirred by large-diameter impellers, resulting in a high dissolved oxygen content and good bulk circulation, which positively affected hyphal growth and metabolism. However, a large-diameter six-blade impeller created overly high shear compared to a large-diameter four-blade impeller, thereby decreasing the conversion ratio. The average shear rates of the former and latter cases were 43.25 s^-1 and 35.31 s^-1, respectively. We therefore concluded that appropriate shear should be applied in the 11α-hydroxylation of canrenone. Overall, this study provides basic data for the scaled-up production of 11α-hydroxycanrenone.

• Journal of Trauma and Injury
• /
• 제32권1호
• /
• pp.26-31
• /
• 2019

Purpose: Rhabdomyolysis (RB) is a syndrome characterized by the decomposition of striated muscles and leakage of their contents into the bloodstream. Acute kidney injury (AKI) is the most significant and serious complication of RB and is a major cause of mortality in patients with RB. Severe RB (creatine kinase [CK] ${\geq}5,000$) has been associated with AKI. However, early prediction is difficult because CK can reach peak levels 1-3 days after the trauma. Hence, the aim of our study was to identify predictors of severe RB using initial patient information and parameters. Methods: We retrospectively analyzed 1,023 blunt trauma patients admitted to a single tertiary hospital between August 2011 and March 2018. Patients with previously diagnosed chronic kidney disease were excluded from the study. RB and severe RB were defined as a CK level ${\geq}1,000U/L$ and ${\geq}5,000U/L$, respectively. The diagnosis of AKI was based on RIFLE criteria. Results: The overall incidence of RB and severe RB was 31.3% (n=320) and 6.2% (n=63), respectively. On multivariable analysis, male sex (odds ratio [OR] 3.78, 95% confidence interval [CI] 1.43 to 10.00), initial base excess (OR 0.85, 95% CI 0.80 to 0.90), initial CK (OR 2.07, 95% CI 1.67 to 2.57), and extremity abbreviated injury scale score (OR 1.78, 95% CI 1.39 to 2.29) were found to predict severe RB. The results of receiver operating characteristic analysis showed that the best cutoff value for the initial serum CK level predictive of severe RB was 1,494 U/L. Conclusions: Male patients with severe extremity injuries, low base excess, and initial CK level >1,500 U/L should receive vigorous fluid resuscitation.

• BioChip Journal
• /
• 제12권4호
• /
• pp.332-339
• /
• 2018

The future neuro-prosthetic devices would be required spikes data monitoring through sub-nanoscale transistors that enables to neuroscientists and clinicals for scalable, wireless and implantable applications. This research investigates the spikes monitoring through integrated CNT front-end amplifier for neuro-prosthetic diagnosis. The proposed carbon nanotube-based architecture consists of front-end amplifier (FEA), integrate fire neuron and pseudo resistor technique that observed high electrical performance through neural activity. A pseudo resistor technique ensures large input impedance for integrated FEA by compensating the input leakage current. While carbon nanotube based FEA provides low-voltage operation with directly impacts on the power consumption and also give detector size that demonstrates fidelity of the neural signals. The observed neural activity shows amplitude of spiking in terms of action potential up to $80{\mu}V$ while local field potentials up to 40 mV by using proposed architecture. This fully integrated architecture is implemented in Analog cadence virtuoso using design kit of CNT process. The fabricated chip consumes less power consumption of $2{\mu}W$ under the supply voltage of 0.7 V. The experimental and simulated results of the integrated FEA achieves $60G{\Omega}$ of input impedance and input referred noise of $8.5nv/{\sqrt{Hz}}$ over the wide bandwidth. Moreover, measured gain of the amplifier achieves 75 dB midband from range of 1 KHz to 35 KHz. The proposed research provides refreshing neural recording data through nanotube integrated circuit and which could be beneficial for the next generation neuroscientists.

• 미생물학회지
• /
• 제55권1호
• /
• pp.46-51
• /
• 2019

이 연구에서는 유칼립투스, 유카와 차나무의 ethanol 추출물의 수지를 이용한 분획 혼합물에 대한 항균활성을 평가하였는데 여러 인간 피부 상재균에 낮은 최소저해농도(0.24~3.32 mg/ml)를 나타내었고 항생제 triclosan과 ampicillin보다 우수한 활성을 나타내었다. Time kill assay에서 식물 추출분획 혼합물은 4시간 이내에 미생물 균주의 개체수를 92% 이상 감소시켰고, 모든 미생물 균주의 뉴클레오티드를 상당량 유출시켰으며, 항균 효과는 이가 양이온($Mg^{2+}$과 $Ca^{2+}$)에 영향을 받지 않았다. 이러한 결과는 Eucalyptus sp., Yucca sp., 및 tea tree의 ethanol 추출물의 수지분획 혼합물이 중요한 인간 피부 상재균을 억제하는 효율적인 화장품 방부제로 이용될 수 있음을 시사한다.

• 대한조선학회논문집
• /
• 제56권4호
• /
• pp.335-342
• /
• 2019

The objective of this study is to analyze the mechanical properties of plywood used as a thermal insulating material for LNG CCS (Liquefied Natural Gas, Cargo Containment System). It is created by bonding an odd number of parallel and perpendicular direction for preventing contraction and expansion of wood. Also plywood is widely used as LNG CCS insulating material because of its durability, light weight and high stiffness. Since LNG CCS is loaded with liquid cargo, the impact load by sloshing during operation and the wide temperature range (room temperature, low temperature, cryogenic temperature) exposed during loading, unloading should be considered. The thickness of the plywood which is used for the membrane type MARKIII was selected as the thickness of the test specimen. In this present study, plywood is analyzed by the fracture behavior and mechanical properties of plywood by temperature and grain direction. In addition, it is necessary to analyze the fracture shape and predict the fracture strain by using regression model because the critical load may cause cracks inside the tank, which may affect the leakage of cryogenic liquid.

• 한국수소및신에너지학회논문집
• /
• 제32권4호
• /
• pp.228-235
• /
• 2021

Polymer electrolyte membrane fuel cells (PEMFC) are currently being used in various transport applications such as drones, unmanned aerial vehicles, and automobiles. The power required is different according to the type of use, purpose, and the conditions adjusted using a cell stack. The fuel cell stack is compressed to reduce the size and prevent fuel leakage. The unit cells that make up the cell stack are subjected to compression by clamping force, which makes geometrical changes in the porous media and it impacts on cell performance. In this study, finite elements method (FEM) and computational fluid dynamics (CFD) analysis for the deformed unit cell considering the effects of clamping force is performed. First, structural analysis using the FEM technique over the deformed gas diffusion layer (GDL) considering compression is carried out, and the resulting porosity changed in the GDL is calculated. The PEMFC model is then verified by a three-dimensional, two-phase fuel cell simulation applying the physical properties and geometry obtained before and after compression. The detailed simulation results showed different concentration distributions of fuel between the original and deformed geometry, resulting in the difference in the distribution of current density is represented at compressed GDL region with low oxygen concentration.