• Radiation Oncology Journal
• /
• v.19 no.1
• /
• pp.66-73
• /
• 2001

Purpose : For the research of Boron Neutron Capture Therapy (BNCT), fast neutrons generated from the MC-50 cyclotron with maximum energy of 34.4 MeV in Korea Cancer Center Hospital were moderated by 70 cm paraffin and then the dose characteristics were investigated. Using these results, we hope to establish the protocol about dose measurement of epi-thermal neutron, to make a basis of dose characteristic of epi-thermal neutron emitted from nuclear reactor, and to find feasibility about accelerator-based BNCT. Method and Materials : For measuring the absorbed dose and dose distribution of fast neutron beams, we used Unidos 10005 (PTW, Germany) electrometer and IC-17 (Far West, USA), IC-18, ElC-1 ion chambers manufactured by A-150 plastic and used IC-l7M ion chamber manufactured by magnesium for gamma dose. There chambers were flushed with tissue equivalent gas and argon gas and then the flow rate was S co per minute. Using Monte Carlo N-Particle (MCNP) code, transport program in mixed field with neutron, photon, electron, two dimensional dose and energy fluence distribution was calculated and there results were compared with measured results. Results : The absorbed dose of fast neutron beams was $6.47\times10^{-3}$ cGy per 1 MU at the 4 cm depth of the water phantom, which is assumed to be effective depth for BNCT. The magnitude of gamma contamination intermingled with fast neutron beams was $65.2{\pm}0.9\%$ at the same depth. In the dose distribution according to the depth of water, the neutron dose decreased linearly and the gamma dose decreased exponentially as the depth was deepened. The factor expressed energy level, $D_{20}/D_{10}$, of the total dose was 0.718. Conclusion : Through the direct measurement using the two ion chambers, which is made different wall materials, and computer calculation of isodose distribution using MCNP simulation method, we have found the dose characteristics of low fluence fast neutron beams. If the power supply and the target material, which generate high voltage and current, will be developed and gamma contamination was reduced by lead or bismuth, we think, it may be possible to accelerator-based BNCT.

• Korean Journal of Weed Science
• /
• v.15 no.1
• /
• pp.13-18
• /
• 1995

This experiment was carried out to investigate occurrence ecology and control of soil-flakes in flood-direct seeded rice field. The occurrence of soil-flakes were inhibited in blue light of 450nm wave length and promoted in red light of 660nm wave length. The diatoms of Pinnularia spp. largely occurred in low fertilizer level and which much more increased when nitrogen was mixed with thinly soil depth. The diatoms of Pinnularia spp. were effectively controlled by carbamate and triazine herbicides when treated in pre-emergence of soil-flakes. Beside, triazine herbicides, simetryne, dimethametryn, prometryne 5g ai/10a showed high control effect in pre and post-emergence of soil-flakes. Expecially, In water-direct seeded rice pyrazosulfuron-methyl molinate simetryne 5.37% GR and dimepiperate bensulfuron dimethametryn 7.643% GR showed high control effect on the soil-flakes when treated at 10 days after seeding and didn't showed rice injury.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.10
• /
• pp.668-676
• /
• 2018

Most reservoirs in Korea have a low water depth and are small in size. Water pollution of the reservoir is serious because of the organic matter flowing from livestock wastewater, domestic sewage, and farmland. In this study, an attempt was made to improve the water purification effect by replacing the secondary dam installed in the depression area of the agricultural reservoir with the riprap dam. To evaluate the long-term performance, a riprap dam was installed in a reservoir in Gyeonggi province and water purification effect for 36 months was measured. The field test results showed that COD was 14.6%, SS 38.6%, T-N 9.5%, and T-P 11.2%. The concentrations in the influent water exhibited a significant change according to season, and the water purification effect increased with increasing concentration of influent water. The pollutant flowing into the lake from the depression area can be blocked effectively if the secondary riprap dam for water purification is installed in the agricultural reservoir.

• Journal of Ecology and Environment
• /
• v.42 no.4
• /
• pp.210-218
• /
• 2018

Background: Soil respiration (Rs) is a major factor of the absorption and accumulation of carbon through photosynthesis in the ecosystem carbon cycle. This directly affects the amount of net ecosystem productivity, which affects the stability and sustainability of the ecosystem. Understanding the characteristics of Rs is indispensable to scientifically understand the carbon cycle of ecosystems. It is very important to study Rs characteristics through analysis of environmental factors closely related to Rs. Rs is affected by various environmental factors, such as temperature, precipitation, soil moisture, litter supply, organic matter content, dominant plant species, and soil disturbance. This study was conducted to analyze the effects of micro-topographical differences on Rs in forest vegetation by measuring the Rs on the ridge and southern slope sites of the broadly established Quercus mongolica forest in the central Korean area. Method: Rs, Ts, and soil moisture data were collected at the southern slope and ridge of the Q. mongolica forest in the Mt. Jeombong area in order to investigate the effects of topographical differences on Rs. Rs was collected by the closed chamber method, and data collection was performed from May 2011 to October 2013, except Winter seasons from November to April or May. For collecting the raw data of Rs in the field, acrylic collars were placed at the ridge and southern slope of the forest. The accumulated surface litter and the soil organic matter content (SOMC) were measured to a 5 cm depth. Based on these data, the Rs characteristics of the slope and ridge were analyzed. Results: Rs showed a distinct seasonal variation pattern in both the ridge and southern slope sites. In addition, Rs showed a distinct seasonal variation with high and low Ts changes. The average Rs measurements for the two sites, except for the Winter periods that were not measured, were $550.1\;mg\;CO_2m^{-2}h^{-1}$ at the ridge site and $289.4\;mg\;CO_2m^{-2}h^{-1}$ at the southern slope, a difference of 52.6%. There was no significant difference in the Rs difference between slopes except for the first half of 2013, and both sites showed a tendency to increase exponentially as Ts increased. In addition, although the correlation is low, the difference in Rs between sites tended to increase as Ts increased. SMC showed a large fluctuation at the southern slope site relative to the ridge site, as while it was very low in 2013, it was high in 2011 and 2012. The accumulated litter of the soil surface and the SOMC at the depth range of 0~5 cm were $874g\;m^{-2}$ and 23.3% at the ridge site, and $396g\;m^{-2}$ and 19.9% at the southern slope site. Conclusions: In this study, Rs was measured for the ridge and southern slope sites, which have two different results where the surface litter layer is disturbed by strong winds. The southern slope site shows that the litter layer formed in autumn due to strong winds almost disappeared, and while in the ridge site, it became thick due to the transfer of litter from the southern slope site. The mean Rs was about two times higher in the ridge site compared to that in the southern slope site. The Rs difference seems to be due to the difference in the amount of litter accumulated on the soil surface. As a result, the litter layer supplied to the soil surface is disturbed due to the micro-topographical difference, as the slope and the change of the community structure due to the plant season cause heterogeneity of the litter layer development, which in turn affects SMC and Rs. Therefore, it is necessary to introduce and understand these micro-topographical features and mechanisms when quantifying and analyzing the Rs of an ecosystem.

• Magazine of the Korean Society of Agricultural Engineers
• /
• v.14 no.1
• /
• pp.2503-2519
• /
• 1972

The studies were carried out to find the cause and the quantitative evaluation of sea dike materials loss which is occured during the period of construction works for the tideland reclamation projects on the west coast of Korea. Major subjects to studies were to establish the typical relationships between the tidal flow and the movement of dike materials, the tidal-flow and the erosion, the dike materials and the ratio of material movement(losses), construction methods and the ratio of materials movement (losses). Based on the above subjects, the studies were made for the purpose of obtain the following informations; (1) Collecting and evaluaing the data of dike material losses due to foundation settlement, from designed existing dikes on the west coast. (2) By the field investigation at A-San Sea Dike, Pyong Taek Project, the Comparison would be made by the relationships between the tide velocity and the movement of dike foundation under the natural conditions and the period of construction so that find out the relationship between the dike materials of foundation situation and settlements. With regard to the dike construction works, it is so difficult to calculate the exact quantity of material losses due to the foundation settlements. The major factors that affect the settlement losses of the dike materials are: (1) Topographical variation (2) Swepting the sectional area of dike by the tide velocity. (3) Dumping riprap to the outerside of dike during the period of construction works. (4) Sectional area losses by the cause of occurence of the new tide channels. (5) material losses by the heavy storms. (6) Consolidation settlement by the foundation weakness. (7) Material losses by the earth materials by tide flow. Most hi호 material losses were occured by the Consolidation settlement due to the foundation weakness, the maximum tide velocities due to decrease the cross sectional area of the gaps and erosion of foundation due to the range of tide, Inner and outerside of dike, or dike material loses due to the tide flow. Final conclusion would be obtained by the continuous measurement of consolidation settlement at the stage of final clusure of the dike. (It is scheduled to close on the end of 1972) However, intermediate conclusion can be introduced as follows: (1) The estimation of material(losses) during the period of construction works for the existing sea-dikes up to date were only empirical. The material losses at the general closure for design was estimated at 10% of the riprap, 20% of the earth materials, and 20% of the riprap, 40% of the earth materials at the final closure of the dike. The final closure estimated double quantity to the general closure, but it is still doubt. (2) The ratio of consolidation settlements was found smaller than the calculated quantity. It can be foreseen that settlement speeds is higher thom the calculated speeds. (3) The movement of dike foundation under the natural conditions were not so depends on the geological conditions of the foundation. (4) When the tide velocities was estimated 100 at the normal tide, it was estimated 125 at the high tide and 55 at the low tide. The tide velocities at the low tide shows apparently lower than the high tide and the higher velocities at the deep water depth.

• Progress in Medical Physics
• /
• v.27 no.3
• /
• pp.146-155
• /
• 2016

As the probability of exposure to radiation increases due to an increase in the use of radioisotopes and radiation generators, the importance of a radiation safety management field is being highlighted. We intend to help radiation workers with exposure management by identifying the degree of radiation exposure and contamination to determine an efficient method of radiation safety management. The personal exposure doses of the radiation workers at the Korea Institute of Radiological & Medical Sciences measured every quarter during a five-year period from Jan. 1, 2011 till Dec. 31, 2015 were analyzed using a TLD (thermoluminescence dosimeter). The spatial dose rates of radiation-controlled areas were measured using a portable radioscope, and the level of surface contamination was measured at weekly intervals using a piece of smear paper and a low background alpha/beta counter. Though the averages of the depth doses and the surface doses in 2012 increased from those in 2011 by about 14%, the averages were shown to have decreased every year after that. The exposure dose of 27 mSv in 2012 increased from that in 2011 in radiopharmaceutical laboratories and, in the case of the spatial dose rate, the rate of decrease in 2012 was shown to be similar to the annual trend of the whole institute. In the case of the surface contamination level, as the remaining radiation-controlled area with the exception of the I-131 treatment ward showed a low value less than $1.0kBq/m^2$, the annual trend of the I-131 treatment ward was shown to be similar to that of the entire institute. In conclusion, continuous attention should be paid to dose monitoring of the radiation-controlled areas where unsealed sources are handled and the workers therein.

• Journal of Environmental Science International
• /
• v.28 no.12
• /
• pp.1061-1069
• /
• 2019

Common reed (Phragmites australis) is widespread in reclaimed land and wetland habitats. Every year, the common reed produces extensive colonies by means of underground rhizomes and ground-surface stolons. From an agricultural point of view, the common reed's large biomass is a good material for supplying organic matter. However, it has not yet been studied in terms of seedling production, transplanting conditions, and decomposition characteristics in reclaimed land. Seeds were harvested from the native common reed in Saemangeum, South Korea, the previous year and stored on an open field. The seeds were sowed in the greenhouse at the beginning of April. Common reed decomposition was studied from June to September, with the use of coarse mesh (5 mm) stem litterbags, on three samping dates and with five replicate packs per sample. These packs were dug in five soil condition (low-salinity topsoil, subsoil, high-salinity topsoil, subsoil, paddy topsoil) to 0.2 m and 0.4 m depth. The highest germination rate of common reed seeds was observed in non-salt solution, but the exhibited germination rate was 70% at 9.38 dS m^-1. The plant height of young reed decreased steadily with increasing salinity, but leaf number did not decrease by 9.38 dS m^-1. The survival rate of the two-year-old reed was 83.3%, which was 35% higher than that of the one-year reed. The transplant success rate was 0% in the no vinyl mulching in the soil, but the first year and second year seedlings survived rates were 63% and 83.3%, respectively, in vinyl mulching. Common reed decomposition rates were faster low salinity than high salinity. All nutrient contents were found to fluctuate significantly with time by soil conditions. We also need to study the growth rate of reed transplanting seedlings by soil moisture contents and the comparison of degradation in common reed tissues.

• Health Policy and Management
• /
• v.32 no.4
• /
• pp.368-379
• /
• 2022

Background: This study aimed to establish a strategy to improve the poor working environment and working conditions among long-term healthcare workers in Korea. Methods: A total of 600 questionnaires with which long-term health care workers participated in the targeted base areas of each city and province nationwide were distributed directly and 525 responses were collected and 506 responses were analyzed. Surveys, on-site field visits, and in-depth interviews were also conducted to understand the working environment as well as conditions and establish a strategy for improving the working environment among long-term healthcare workers to understand the demands of working conditions and working conditions. Results: Korean long-term care workers firstly and mostly enumerated their risk factors for ill-health when lifting or moving elderly recipients directly by hand (69.9%), followed by increased physical workload with old beds, tools, and facilities (42.3%) in the workplaces, shortage of manpower (32%), and source of infection (30%). To improve the working environment as well as conditions, Korean long-term care workers considered improving low-wage structures, ergonomic improvements to solve excessive physical loads, and increasing various bonus payments as well as implementing the salary system, positive social awareness, and increasing resting time. Of 506 responses, 92.3% replied that the long-term care insurance system for the elderly should be developed to expand publicization at the national level. Conclusion: This study proposes to improve the low-wage structure of Korean long-term care workers, automation and improvement of facilities, equipment, and tools to eliminate excessive physical loads (beneficiary elderly lifting), and reduction of night labor.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.51-51
• /
• 2010

Recently just as in the automobile industry, shipbuilders also try to reduce material consumption and weight in order to keep operating costs as low as possible and improve the speed of production. Naturally industry is ever searching for welding techniques offering higher power, higher productivity and a better quality. Therefore it is important to have a details research based on the various welding process applied to steel and other materials, and to have the ability both to counsel interested companies and to evaluate the feasibility of implementation of this process. Submerged-arc welding (SAW) process is usually used about 20% of shipbuilding. Similar to gas metal arc welding(GMAW), SAW involves formation of an arc between a continuously-fed bare wire electrode and the work-piece. The process uses a flux to generate protective gases and slag, and to add alloying elements to the weld pool and a shielding gas is not required. Prior to welding, a thin layer of flux powder is placed on the work-piece surface. The arc moves along the joint line and as it does so, excess flux is recycled via a hopper. Remaining fused slag layers can be easily removed after welding. As the arc is completely covered by the flux layer, heat loss is extremely low. This produces a thermal efficiency as high as 60% (compared with 25% for manual metal arc). SAW process offers many advantages compared to conventional CO2 welding process. The main advantages of SAW are higher welding speed, facility of workers, less deformation and better than bead shape & strength of welded joint because there is no visible arc light, welding is spatter-free, fully-mechanized or automatic process, high travel speed, and depth of penetration and chemical composition of the deposited weld metal. However it is difficult to application of thin plate according to high heat input. So this paper has been focused on application of the field according to SAW process for thin plate in ship-structures. For this purpose, It has been decided to optimized welding condition by experiments, relationship between welding parameters and bead shapes, mechanical test such as tensile and bending. Also finite element(FE) based numerical comparison of thermal history and welding residual stress in A-grade 3.2 thickness steel of SAW been made in this study. From the result of this study, It makes substantial saving of time and manufacturing cost and raises the quality of product.

• The Korean Journal of Pesticide Science
• /
• v.17 no.3
• /
• pp.168-177
• /
• 2013

This experiment was carried out to estimate leaching potential of thirteen endocrine disruptor-suspected pesticides in upland soils using soil columns (5 cm I.D. ${\times}$ 35 cm H.) packed with soil A (sandy loam) and soil B (loam). When 12.6 mL of water, average precipitation in Cheongju area during the period from June to August, 2001-2010, was percolated through soil column packed with soil A every day for 21 days, no pesticides were detected from leachate, with the exception of metribuzin which was detected with negligible. Also, when 2 L of water was percolated consecutively five times through soil columns packed with soil A and B, irrespective of soil types, cypermethrin, endosulfan, fenvalerate, parathion and trifluralin, which were very low water solubilities and high soil $K_{oc}s$, were not detected from leachate and were distributed mostly in the depth of 0-5 cm, representing that water solubility and soil $K_{oc}$ are major contributing factors to their leaching behavior. Despite high average leaching rates in carbaryl and methomyl, actual possibilities of ground water contamination in the agricultural environment by them would be very low, considering that the negligible amount of pesticide was percolated through a lysimeter with an undisturbed soil core simulating the field conditions, while most of pesticide was percolated through a soil column with the disturbed soil profile.