• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2021.05a
• /
• pp.127-128
• /
• 2021

Rigid urethane foam is widely applied because it is light and has superior insulation performance compared to insulation materials such as EPS or glass wool. However, it has the disadvantage of being vulnerable to fire. Therefore, in this study, before proceeding with the research to improve the fire resistance of the rigid polyurethane foam, we would like to investigate the change in density and thermal conductivity of the rigid polyurethane foam according to the change in the mixed weight of the main material and the curing agent. It was found that the density increased as the mixed weight increased. The thermal conductivity showed similar values overall. As for the density distribution, the central part was low and the outer part was high.

• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2023.05a
• /
• pp.45-46
• /
• 2023

CLC is used as a filling material for many buildings, and according to energy saving design standards, CLC also requires insulation performance. However, it shows lower insulation performance compared to organic insulation, so additional research is needed. Therefore, in this study, the insulation properties of CLC were analyzed by incorporating EPS beads with high insulation performance into CLC. In this experiment, EPS beads and blast furnace slag were replaced, and W/B was fixed at 33%. The EPS Bead mixing ratio was divided into 5 levels: 0, 0.5, 1.0, 1.5, 2.0 (%), and the experimental items were measured for apparent density and thermal conductivity. As a result of the experiment, the apparent density and thermal conductivity tended to decrease as the mixing ratio of EPS beads increased. It is judged that the density decreased due to the low density and the micropores inside, and the thermal conductivity also decreased.

• Tunnel and Underground Space
• /
• v.13 no.4
• /
• pp.321-329
• /
• 2003

The change of strain-dependent hydraulic conductivity around mined panels due to subsidence is examined where normal and shear strains, modulus reduction ratio and joint spacing are major factors controlling the changes of hydraulic conductivity. Modulus reduction ratio and joint spacing are defined through RMR and RQD, respectively. Utilizing these two empirical parameters, changes of hydraulic conductivity values of a full gamut of rock mass conditions are determined. The change of hydraulic conductivity is not apparent in the near surface area and more significant change takes place in the area around mined panels. A zone of strong influence from the subsidence extends to a height of approximately 20m above mined panels. The shear strain does also play the role of increasing a hydraulic conductivity around mined panels. As RMR of rock mass decreases, a hydraulic conductivity is found to be increased and this means that subsidence in a poor rock with low RMR has a great effect on a hydraulic conductivity field.

• Journal of the Korean Ceramic Society
• /
• v.48 no.5
• /
• pp.368-372
• /
• 2011

Aluminum nitride (AlN) has excellent thermal conductivity, whereas it has some disadvantage such as low sinterability. In this study, the effects of sintering additive content and sintering condition on thermal conductivity of pressureless sintered AlN ceramics were examined on the variables of 1~3 wt% sintering additive ($Y_2O_3$) content at $1900^{\circ}C$ in $N_2$ atmosphere with holding time of 2~10 h. All AlN specimens showed higher thermal conductivity as the $Y_2O_3$ content and holding time increase. The formation of secondary phases (yttrium aluminates) by reaction of $Y_2O_3$ and $Al_2O_3$ from AlN surface promoted the thermal conductivity of AlN specimens, because the secondary phases could reduce the oxygen contents in AlN lattice. Also, thermal conductivity was increased by long sintering time because of the uniform distribution and the elimination of the secondary phases at the grain boundary by the evaporation effect during long holding time. A carbothermal reduction reaction was also affected on the thermal conductivity. The thermal conductivity of AlN specimens sintered at $1900^{\circ}C$ for 10 h showed 130~200W/mK according to the content of sintering additive.

• Korean Journal of Materials Research
• /
• v.15 no.4
• /
• pp.217-223
• /
• 2005

Thermal, electrical and mechanical properties of high purity niobium and tantalum refractory rare metals were investigated tn evaluate the physical purity. Higher purity niobium and tantalum metals showed lower hardness due to smaller solution hardening effect. Temperature dependence of electrical resistivity showed a typical metallic behavior. Remarkable decrease in electrical resistivity was observed for a high purity specimen at low temperature. However, thermal conductivity increased for a high purity specimen, and abrupt increase in thermal conductivity was observed at very low temperature, indicating typical temperature dependence of thermal conductivity for high purity metals. It can be known that reduction of electron-phonon scattering leads to increase in thermal conductivity of high purity niobium and tantalum metals at low temperature.

• Journal of Energy Engineering
• /
• v.20 no.3
• /
• pp.209-215
• /
• 2011

In this study, for efficiency enhancement of low temperature heat exchanger, the thermal conductivity and the viscosity of carbon nanofluids and oxidized carbon nanofluids were measured at $10^{\circ}C$ and $25^{\circ}C$, respectively. Carbon nanofluids were made by ultrasonic-dispersing ones in distilled water after Multi-Walled Carbon Nanotubes (MWCNTs) mixed Sodium Dodecyl Sulfate (SDS, 100 wt%), Polyvinyl pyrrolidone (PVP, 300 wt%) each. Oxidized carbon nanofluids were made by ultrasonic-dispersing Oxidized Carbon Nanotubes (OMWCNTs) in distilled water. The thermal conductivity of carbon nanofluids was measured by using a transient hot-wire method. The viscosity was measured by using a digital viscometer. As a result, the thermal conductivity of oxidized carbon nanofluids was the highest of those compared and the other carbon nanofluids at the same mixture ratio and temperature, and the viscosity was measured the lowest of those compared and the other carbon nanofluids.

• Membrane Journal
• /
• v.22 no.3
• /
• pp.155-170
• /
• 2012

Fuel cells have been considered as alternative power generation system in the twenty-first century because of eco-friendly system, high power density and efficiency compare with petroleum engine system. Proton exchange membranes (PEMs) are the key components in fuel cell system. Currently, Nafion has been used in fuel cell system. However, Nafion has disadvantages such as low conductivity at high temperature and high cost. The researchers have focused to reach the high properties such as high proton conductivity, low permeability to fuel, good chemical/thermal stability, good mechanical properties and low manufacturing cost. Various methods have been developed for preparation of proton exchange membrane with high performance and commercialization of fuel cell system. The hybrid organic/inorganic membrane has the potentials to provide a unique combination of organic and inorganic properties with improved proton conductivity and mechanical property at high temperatures. So, this paper presents an overview of research trend for the composite membranes prepared by organic/inorganic system using various inorganic materials.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.11a
• /
• pp.82.2-82.2
• /
• 2010

The development of bipolar plate having high efficiency and chemical properties has a major impact on fuel cell applications commercialization. Even though graphite bipolar plate has high electric conductivity and chemical resistance, it has demerits about mass production and brittle property for commercialization. Hence, metallic bipolar plate can be substitute for fuel cell bipolar plate. Although its inadequate corrosion behavior under PEMFC environment lead to a deterioration of membrane by dissolved metal ions, metallic bipolar plate for PEMFC is more suitable for automotive and residential power generation system because of its high mechanical strength, low gas permeability and applicability to mass production. Therefore, several types of coating has been applied to prevent corrosion and oxide film growth and to achieve more high durability. This work presents durability of coated metal bipolar plate for low temperature PEMFC which made for fuel cell vehicle. This results showed surface treatment increase long-term durability, even electric conductivity and corrosion resistance.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.25 no.6
• /
• pp.845-852
• /
• 2001

The characteristics of evaporation cooling of single droplet on a heated surface were studied experimentally. The two kinds of heater modules were tested to measure cooling characteristics of metal surface (high conductivity) and Teflon surface (low-energy surface, low conductivity). The results showed that time averaged heat flux during droplet evaporation increased exponentially with initial surface temperatures of brass, copper and steel. The heat flux and evaporation time did not varied with metal conductivities. However, the temperature drop after the deposition of droplet was larger on Teflon than on the metals. Thus, the correlation of interface temperature between liquid droplet and metal surface was proposed as a function of the initial surface temperature of heating materials, which could be applied to both metal and non-metal ones.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.2
• /
• pp.138-145
• /
• 1993

The bath cryostat of cryogenic apparatuses which are generally used to study physical phenomena under low temperature and ultra low temperature has been desigened and constructed. The practical use of the cryostat is verified by the measurement of the storage life of liquid heloum and liquid nitrogen vessels. The cryostat consists of triple structure of high vacuum environment in order to minimize the evaporation rate of liquid helium and liquid nitrogen by thermal conductivity and radiant heat. The minimum thickness which can stand against inner and outer pressures is calculated from considering the strength of the material.