• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1999.11a
• /
• pp.549-552
• /
• 1999

We have developed an novel vertical-alignment (VA) - $\pi$ cell mode that provides a wide viewing angle and fast response times for negative dielectric anisotropy nematic liquid crystal (NLC) on a homeotropic polyimide (PI) surfaces. We had the good voltage-transmittance curves and low driving voltages were achieved with the novel VA - $\pi$ cell mode without negative compensation film. Iso-viewing angle characteristics using the novel VA - $\pi$ cell mode without negative compensation film of NLC was also successfully observed. As well a fast response time of 31.7ms for the novel VA - $\pi$ cell mode was measured. Consequently, It is seen that by using the novel VA - $\pi$ cell mode the iso-viewing angle, fast response time, and low driving voltage characteristics can be achieved.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.8
• /
• pp.674-681
• /
• 2001

An experiment is conducted to investigate the effect of the inclination angle on convective boiling heat transfer of a uniformly heated tube. The test section used is a stainless steel tube with10.7mm in inner diameter. The hating length is 3m and is heated directly by an AC current. The test fluid is R-113. Experiment are carried out with mass flow rates of 300, 500 and $700\;kg/m^{2}s$, and heat fluxes varying from 5 to 65 kW/$m^2$. The inclination angles of the tube are $0^{\circ},\;5^{\circ},\;11^{\circ}\;and\;25^{\circ}$. the circumferential temperature variation at low quality region and the location of dryout at high quality region are mainly observed. Circumferential anisothermality occurring at low mass flow rate and low quality conditions is gradually reduced with the increase in the inclination angle and finally disappears at the inclination angle of $25^{\circ}$. Critical quality where dryout is initiated is seriously influenced by the inclination angle. Wall temperature after critical quality is also affected by the inclination angle.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.11
• /
• pp.2981-2994
• /
• 1995

In order to elucidate the effects of positive pressure gradient on flame properties, structure and stabilization, an experimental study is made on turbulent diffusion flame stabilized by a circular cylinder in a divergent duct flow. A commercial grade gaseous propane is injected from two slits on the rod as fuel. In this paper, stabilization, characteristics and flame structure are examined by varying the divergent angle of duct. Temperature, ion current and Schlieren photographs were measured. It is found that critical divergent angle is expected to be about 8 ~ 12 degree through blow-off velocity pattern to divergent angle and the positive pressure gradient influences the flame temperature, intensity of ion current and eddy structure behind the rod. With the increase of divergent angle, typical temperature of recirculation zone is low but intensity of ion current is high in shear layer behind rod. Energy distributions of fluctuating temperature and ion current signals turn up low frequency corresponding to large scale eddies but high frequency corresponding to small scale eddies as well as low with the increase of divergent angle. Therefore the flame structure becomes a typical distributed-reacting flame.

• Journal of Korean Medicine Rehabilitation
• /
• v.19 no.2
• /
• pp.289-302
• /
• 2009

Objectives : This study was performed in order to investigate the relation of body composition analysis and radiological parameter(lumbosacral angle, lumbar lordortic angle, lumbar gravity line). Methods : This study was carried out with the data from comprehensive medical testing. 75 subject aged 20-59 performed the segmental bioelectrical impedance analysis, questionnaire. And lumbosacral angle, lumbar lordortic angle and lumbar gravity line were measured in the standing position x-ray. Then we analyzed the data. Results : Low back pain(LBP) prevalence in high obesity index(Body Mass Index(BMI), Percentage of Body Fat(PBF), Waist Hip Ratio(WHR)) group was higher than LBP prevalence in normal obesity index group(p<0.01). In LBP group, lumbosacral angle, lumbar lordortic angle were significantly lager than Non-LBP group(p<0.001). And 75% of LBP group indicated abnormal lumbar gravity line ratio(0.67 < Normal lumbar gravity line ratio <1.00). When it comes to analyze relation between obesity index and radiological parameter, no-significant change was seen. Conclusions : This study carried as following research after the study on relation of obesity, LBP and trunk muscle strength. Results from this investigation showed positive correlation between obesity and LBP prevalence. But obesity index didn't indicate significant correlation with structural changes of lumbar vertebrae. When considering prior research, trunk muscle strength changes were more related to LBP prevelence in obese people. This results are expected to explain causes of LBP in obese group.

• Journal of Korean Foot and Ankle Society
• /
• v.21 no.1
• /
• pp.7-11
• /
• 2017

Purpose: We retrospectively analyzed the radiographic and clinical results after the first ray of forefoot osteotomy using low profile wedge plate without additional cancellous bone grafting for pes planus correction. Materials and Methods: Twenty-four patients were enrolled in this study. Medial cuneiform opening wedge osteotomy was performed in 12 patients (Cotton osteotomy, group C) and first metatarsal base osteotomy was performed in 12 patients (group MT). Results: On average, the wedge size was 5.61 mm (5~6 mm). The mean time to radiographic union was 3.18 and 3.27 months in groups C and MT, respectively. Postoperative talonavicular coverage angle, talo-first metatarsal angle (anteroposterior), talo-first metatarsal angle (lateral), talo-calcaneal angle (lateral), medial cuneiform height, and American orthopaedic foot, as well as ankle society midfoot scale were significantly improved in both groups. Nonunion, delayed union or fixation failure was not presented in our series. Conclusion: We have shown that low profile wedge plate was effective in the case of first ray forefoot osteotomy for pes planus correction without any additional cancellous bone grafting.

• Journal of Power Electronics
• /
• v.18 no.3
• /
• pp.714-722
• /
• 2018

This paper presents a wide-range speed control scheme of brushless DC (BLDC) motors based on a hall sensor with separated low- and normal-speed controllers. However, the use of the hall sensor signal is insufficient to detect motor speed in the low-speed region because of low sensor resolution and time delay. In the proposed method, a micro-stepping current control method according to the torque angle variation is presented. In this mode, the motor current frequency and rotating angle are determined by the reference speed without the actual speed fed by the hall sensor. The detected torque angle is used to adjust the current value in a limited band to control the current value in accordance with the load. The torque angle is detected exactly at the changing point of the hall sensor signal. The rotor can follow the rotating flux with the variable torque angle. In a normal speed range, the conventional vector control scheme is used to control the motor current with a PI speed controller using the hall sensor. The torque characteristics are analyzed on the basis of the back EMF and current shape. To adopt the vector control scheme, the continuous rotor position is estimated by the measured speed and hall sensor position. At the mode changing point between low and normal speed range, the proper initial current command and reference rotor position are calculated. The calculated current command can reduce the torque ripple during transient mode. The proposed method is simple but effective in extending the speed control range of a conventional BLDC motor with hall sensor without the need for a high-resolution encoder. The effectiveness of the proposed method is verified by various experiments on a practical BLDC motor.

• Applied Chemistry for Engineering
• /
• v.21 no.1
• /
• pp.98-103
• /
• 2010

The effect of plasma treatment on surface characteristics of polycarbonate (PC) films was investigated using low pressure plasma and atmospheric pressure plasma with oxygen and argon. Untreated PC has a contact angle of $82.31^{\circ}$ with de-ionized water which reduced to $9.17^{\circ}$ as the lowest value after being treated with a low pressure plasma treatment with oxygen. Increase of delivered powers such as RF and AC with a high frequency and gas flow rates was not effective to reduce contact angles dramatically but gave the trend of reducing gradually. The surface of PC treated with plasma shows a low contact angle but the contact angle increases rapidly according to the exposure time in air ambient. Oxygen plasma was more effective to generate the polar functional group regardless of the type of plasma. Conclusively, a low plasma treatment with oxygen is more recommendable when the hydrophilic surface of PC is required.

• Journal of the Korean Vacuum Society
• /
• v.15 no.4
• /
• pp.387-394
• /
• 2006

In this study, the effect of using a neutral beam formed by low-angle forward reflection of a reactive ion beam on aspect-ratio-dependent etching (ARDE) has been investigated. When a SF6 Inductively Coupled Plasma and $SF_6$ ion beam etching are used to etch poly-Si, ARDE is observed and the etching of poly-Si on $SiO_2$ shows a higher ARDE effect than the etching of poly-Si on Si. However, by using neutral beam etching with neutral beam directionality higher than 70 %, ARDE during poly-Si etching by $SF_6$ can be effectively removed, regardless of the sample conditions. The mechanism for the removal of ARDE via a directional neutral beam has been demonstrated through a computer simulation of different nanoscale features by using the two-dimensional XOOPIC code and the TRIM code.

• Physical Therapy Korea
• /
• v.10 no.1
• /
• pp.63-76
• /
• 2003

This research was performed to compare spinal segment motion angle between low back pain (LBP) group and painless group during trunk flexion-extension and to investigate the effect of transversus abdominis strengthening exercise on spinal segment motion angle in LBP group. Nine subjects with LBP and ten subjects without LBP participated. Transversus abdominis strengthening exercise was performed in LBP group for three weeks, and spinal segment motion angles were compared before and after the exercise performance. Spinal segment motion angles were measured both in sitting and standing position. Results were as followed: 1) Subjects' average age was 24.79 years, height was 167.84 cm, and weight was 59.95 kg. 2) Spinal segment motion angle of T10/l1 was significantly higher in LBP group compared with painless group (p<.05) in sitting position during trunk flexion-extension. 3) In sitting position, whereas entire lumbar segment motion angles were lower in LBP group compared with painless group (p<.05), angle of L4/5 was higher in LBP group compared with painless group (p<.05). 4) There was no significant difference in thoracic segment motion angle in standing position. 5) After three weeks of transversus abdominis strengthening exercise, thoracic segment motion angle increased both in sitting and standing position (p<.05). 6) In painless group, there was no significant difference in entire spinal segment motion angles in sitting and standing position (p>.05). When spinal segment motion angles were compared between sitting and standing position, there were slight differences. In sitting position, there was no difference in spinal segment motion angle between LBP group and painless group while hip joint motion angle and sacral inclination angle of LBP group was lower than those of painless group (p<.05). In standing position, lumbar segment motion angle was significantly lower in LBP group than that of painless group. Transversus abdominis strengthening exercise influenced thoracic segment motion angle more significantly than lumbar segment motion angle.

• ETRI Journal
• /
• v.32 no.6
• /
• pp.837-842
• /
• 2010

This paper proposes robust source localization methods for estimating the azimuth angle, elevation angle, velocity, and range using a low-complexity planar antenna array in impulsive non-Gaussian noise environments. The proposed robust source localization methods for wireless communication applications are based on nonlinear M-estimation provided from Huber and Hampel. Simulation results show the robustness performance of the proposed robust methods in impulsive non-Gaussian noise.