• 비파괴검사학회지
• /
• 제21권3호
• /
• pp.251-260
• /
• 2001

단조인장시험하에서 CFRP적층재의 손상과정을 음향방출과 초음파시험에 의해 평가하였다. 시험편으로부터의 음항방출신호의 진폭 분포는 기지재 균열(matrix crack), 박리(debonding), 섬유 pull-out 및 섬유 과단(fiber fracture)과 같은 CFRP에서의 파괴기구를 분석하는데 도움을 주며, 초음파 진폭감쇠의 특성 또한 각각의 파괴기구를 분석하는데 유용하다. 여러종류의 CFRP시험편을 사용하여 음향방출신호와 초음파신호의 진폭감쇠를 조사하였다. 끝으로 하중 제하중(loading-unloading) 시험이 초음파내의 진폭비에 대한 Felicity effect와 감쇠를 조사하기 위해서 수행되었다. 전 실험에 걸쳐 초음파신호의 진폭감쇠와 음향방출 파라미터(parameter)들은 동시에 검출되었다. 이로써 음향방출과 초음파시험의 두 파라미터들이 CERP에서의 파괴기구를 분석하기 위해 효과적으로 사용될 수 있음이 확인되었다.

• 대한토목학회논문집
• /
• 제8권2호
• /
• pp.33-40
• /
• 1988

본 연구에서는 밀도와 구속압력이 노상토의 탄성계수에 미치는 영향을 살펴보기 위하여 전국 고속도로로 노상토를 채취분석하여 얻은 전형적인 5가지 노상토 재료에 대하여 함수비, 밀도 및 구속압력을 달리하면서 비압밀 비배수 삼축압축시험을 실시하였다. 삼축압축시험시 unloading-reloading 실험을 수행하여 얻은 응력-변형을 관계로부터 최대탄성계수를 측정하였다. 실험결과 노상토의 탄성거동은 Janbu의 제안식에 잘 부합하였으며, 구속압력으로 표준화된 탄성계수는 건조단위체적중량과 지수함수의 상관관계가 있음을 알 수 있었다. 또한 포화도가 70%이하에서는 함수비가 탄성계수에 영향을 거의 미치지 않음이 밝혀졌다.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.3-11
• /
• 2002

A moment-curvature relationship to simulate the behavior of reinforced concrete (RC) columns under cyclic loading is introduced. Unlike previous moment-curvature models and the layered section approach, the unposed model takes into account the bond-slip effect by using a monotonic moment-curvature relationship constructed on the basis of the bond-slip relation and corresponding equilibrium equation at each nodal point. In addition, the use of curved unloading and reloading branches inferred from the stress-strain relation of steel gives more exact numerical result. The pinching enact caused by axial force is considered with an assumption that the absorbing energy corresponding to any deformation level maintains constant regardless of the magnitude of applied axial force. The advantages of the proposed model, comparing tn layered section approach, may be on the reduction in calculation time and memory space in case of its application to large structures.. Finally, correlation studies between analytical results and experimental studies are conducted to establish the validity of the proposed mood.

• 한국기계가공학회지
• /
• 제11권1호
• /
• pp.95-100
• /
• 2012

A deck crane is installed on the deck of a ship when there is no adequate facility for loading and unloading in dock or harbor. Deck cranes in Korea have been imported from abroad, and the import-substitution effect will arise if its production can be localized. Now, it is required to suggest the structural design of a deck crane that meet the domestic criterion, considering loading condition. In this study, the structural analysis of a pedestal in the deck crane was peformed by finite element method to investigate the strength requirement. In addition, the structural design of a pedestal was suggested by using ANSYS and VisualDOC. The optimized structure of a pedestal was determined, considering lightweight design.

• 대한조선학회논문집
• /
• 제43권2호
• /
• pp.220-227
• /
• 2006

In case of welding, the inherent strains are generated, because a structure experiences the plastic yielding. The inherent strain is defined as the irrecoverable strain after removing structural restraints and loading. For the analysis method of welding distortion, equivalent loading method based on inherent strain is in general use due to its efficiency and effectiveness. However, it is generally difficult to know the final strain of the welded structure if additional loadings were applied after welding. for this reason, this study introduced the concept of the hardening and added the hardening term to the equivalent loading method based on inherent strain. Therefore, the purposes of this study are to develop the inherent strain formula considering the hardening effect and to calculate residual Stresses Using Proposed inherent Strain. Also, this Study Verified the availability Of proposed inherent strain method by loading-unloading experiment on welded plate.

• Structural Engineering and Mechanics
• /
• 제17권3_4호
• /
• pp.357-378
• /
• 2004

Nonlinear dynamic analysis of a reinforced concrete (RC) frame under earthquake loading is performed in this paper on the basis of a hysteretic moment-curvature relation. Unlike previous analytical moment-curvature relations which take into account the flexural deformation only with the perfect-bond assumption, by introducing an equivalent flexural stiffness, the proposed relation considers the rigid-body-motion due to anchorage slip at the fixed end, which accounts for more than 50% of the total deformation. The advantage of the proposed relation, compared with both the layered section approach and the multi-component model, may be the ease of its application to a complex structure composed of many elements and on the reduction in calculation time and memory space. Describing the structural response more exactly becomes possible through the use of curved unloading and reloading branches inferred from the stress-strain relation of steel and consideration of the pinching effect caused by axial force. Finally, the applicability of the proposed model to the nonlinear dynamic analysis of RC structures is established through correlation studies between analytical and experimental results.

• Smart Structures and Systems
• /
• 제30권2호
• /
• pp.183-193
• /
• 2022

Structural health monitoring and structural vibration control are multidisciplinary and frontier research directions of civil engineering. As intelligent materials that integrate sensing and actuation capabilities, shape memory alloys (SMAs) exhibit multiple excellent characteristics, such as shape memory effect, superelasticity, corrosion resistance, fatigue resistance, and high energy density. Moreover, SMAs possess excellent resistance sensing properties and large deformation ability. Superfine NiTi SMA wires have potential applications in structural health monitoring and micro-drive system. In this study, the mechanical properties and electrical resistance sensing characteristics of superfine NiTi SMA wires were experimentally investigated. The mechanical parameters such as residual strain, hysteretic energy, secant stiffness, and equivalent damping ratio were analyzed at different training strain amplitudes and numbers of loading-unloading cycles. The results demonstrate that the detwinning process shortened with increasing training amplitude, while austenitic mechanical properties were not affected. In addition, superfine SMA wires showed good strain-resistance linear correlation, and the loading rate had little effect on their mechanical properties and electrical resistance sensing characteristics. This study aims to provide an experimental basis for the application of superfine SMA wires in engineering.

• Geomechanics and Engineering
• /
• 제37권4호
• /
• pp.341-358
• /
• 2024

This paper reports several plane-strain trapdoor tests conducted to investigate the effects of reinforcement on soil arching development under localized surface loading with a loading plate width three times the trapdoor width. An analogical soil composed of aluminum rods with three different diameters was used as the backfill and Kraft paper with two different stiffness values was used as the reinforcement material. Four reinforcement arrangements were investigated: (1) no reinforcement, (2) one low stiffness reinforcement R1, (3) one high stiffness reinforcement R2, and (4) two low stiffness reinforcements R1 with a backfill layer in between. The stiffness of R2 was approximately twice that of R1; therefore, two R1 had approximately the same total stiffness as one R2. Test results indicate that the use of reinforcement minimized soil arching degradation under localized surface loading. Soil arching with reinforcement degraded more at unloading stages as compared to that at loading stages. The use of stiffer reinforcement had the advantages of more effectively minimizing soil arching degradation. As compared to one high stiffness reinforcement layer, two low stiffness reinforcement layers with a backfill layer of certain thickness in between promoted soil arching under localized surface loading. Due to different states of soil arching development with and without reinforcement, an analytical multi-stage soil arching model available in the literature was selected in this study to calculate the average vertical pressures acting on the trapdoor or on the deflected reinforcement section under both the backfill self-weight and localized surface loading.

• Journal of Biosystems Engineering
• /
• 제17권2호
• /
• pp.156-170
• /
• 1992

The force-deformation relationship gives the basic physical properties of the fruits such as the bioyield point, the rupture point, and the deformations at the bioyield point and the rupture point. These informations are very important to study the stress-strain relationships of the fruits. This study was conducted to analyze those physical properties according to the sampling position of the fruits, and to determine the bioyield point, the rupture point, and the deformations at the bioyield point and the rupture point of the fruits for two different storage conditions(low temperature and normal temperature) and the storage period, and to investigate the effect of loading rate on those physical properties, the hysteresis on the loading-unloading condition and the degree of elasticity of the fruits. The results of the study were as follows : 1. The physical properties(BS, US, BD, and RD) of the test specimen selected from the different sampling positions were quite different. The values of the physical properties were shown smallest ones at the cheek of the fruits, and the statistical test results of the physical properties between the cheek from the other two positions of the fruits showed that there were significant difference at the 1 % level between them. 2. The effect of loading rate on the physical properties of the fruits was relatively large, all the considered physical propertis of the fruits increased with the loading rate, but the hysteresis loss decreased with it. 3. The physical properties of the fruits according to the storage conditions and period showed different, and the bioyield deformation and the rupture deformation of the fruits increased with the storage period, but the bioyield strength and the ultimate strength of the fruits decreased with it. The effect of the storage conditions on the those physical properties showed that the normal temperature storage condition was a little higher than the low temperature storage condition. 4. As a whole, it was shown that the bioyield strength and the ultimate strength of the pear decreased a little faster than those of the apple, and the bioyield deformation and rupture deformation of the pear increased a little faster than those of apple at the two storage conditions.

• 대한치과교정학회지
• /
• 제37권6호
• /
• pp.432-439
• /
• 2007

초탄성 니켈-티타늄 호선의 하중값은 온도 변화에 따라 변화함이 보고된 바 있다. 따라서 본 연구에서는 온도가 변화함에 따라 니켈-티타늄 합금 호선의 하중값이 어떻게 변화하는지 알아보고자 하였다. $37^{\circ}C$ 항온 상태에서 $0.016"{\times}0.22"$ 니켈-티타늄 호선을 3.1 mm까지 변위시키는 3점 굴곡 실험을 시행하여 하중 시와 탈하중 시의 1.5mm 변위지점의 하중값을 측정하고 이 지점에서 구강내 온도 변화를 고려한 온도 변화 실험을 시행하였다. $20^{\circ}C$ 저온수 또는 $50^{\circ}C$ 고온수를 호선에 흘려보냄으로써 온도 변화를 주었다. 저온 실험은 저온수로 온도 변화를 주고 $37^{\circ}C$ 항온 온도로 회복된 후에 다시 저온수를 흐르게 하는 방법으로 10회 시행하였고 고온 실험도 동일한 방법으로 시행하였다. 그 결과 하중 시 1.5mm 변위지점의 하중값은 저온 실험 및 고온 실험 후 $37^{\circ}C$로 회복된 후에도 모두 감소된 값을 유지하였다. 반대로 실제로 치아에 가해지는 교정력으로 생각되는 탈하중 시 1.5 mm 변위 지점의 하중값은 저온 실험 및 고온 실험 후 온도가 $37^{\circ}C$로 회복되어도 모두 증가된 값을 유지하였다. 이상의 결과를 종합해 볼 때 온도변화를 거친 후 초탄성 니켈-티타늄 합금 호선의 하중 시 힘은 감소하였고 탈하중 시 힘은 증가되므로, 임상에서 니켈-티타늄 호선을 적용 시에는 $37^{\circ}C$에서의 하중-변위 곡선에서 나타나는 힘에 비해 더 작은 하중 시 힘과 더 큰 탈하중 시 힘이 적용될 수 있음에 유의하여야 한다.