• 소성∙가공
• /
• 제3권3호
• /
• pp.291-301
• /
• 1994

In the simultaneous forward-backward extrusion the effects of some process variables including area reduction, stroke advance, materials(Al 2024 and commercial pure copper) on the extrusion load, plastic flow and height ratio of upper to lower extruded parts are experimentally investigated and analyzed. Grid-marking technique is employed to visualize the plastic flow. The influence of using split and original specimen on the extrusion load and height ratio is evaluated by experiments. Experimental results show that the plastic flow if oriented to the part of lower area reduction in the begining but it is usually variated during the overall process. The configurations of plastic deformation and plastic flow are dependent on the working materials and the lubricational conditions.

• Steel and Composite Structures
• /
• 제30권4호
• /
• pp.315-325
• /
• 2019

Double skin composite walls offer structural and economic merits over conventional reinforced concrete counterparts in terms of higher capacity, greater stiffness, and better ductility. This paper investigated the axial behavior of double skin composite walls with steel truss connectors. Full-scaled tests were conducted on three specimens with different height-to-thickness ratios. Test results were evaluated in terms of failure mode, load-axial displacement response, buckling loading, axial stiffness, ductility, strength index, load-lateral deflection, and strain distribution. The test data were compared with AISC 360 and Eurocode 4 and it was found that both codes provided conservative predictions on the safe side.

• 한국지반공학회논문집
• /
• 제31권10호
• /
• pp.49-60
• /
• 2015

기존 3차원 토압연구는 벽체에 작용하는 주동토압을 단일파괴체로 가정하고 벽체의 안정성에 초점을 맞춰 3차원 토압의 크기를 구하는데 역점을 두었고, 토압의 주변지반 전이에 대한 연구는 미진하였다. 따라서 본 연구에서는 벽체의 폭과 높이의 비 즉, 종횡비를 달리하여 3차원 모형실험을 수행하고, 주변지반으로 전이되는 토압의 크기와 영향범위를 파악하였다. 주변지반으로 전이되는 토압은 종횡비에 따라 3차원 주동토압의 감소량보다 17.9~30.6% 작게 나타났으며, 연직방향 토압의 전이보다 수평방향 토압의 전이가 크게 나타났다. 토압의 전이범위는 수평방향으로 주동벽체 폭 w 기준으로 0.67~1.29w, 연직방향으로 주동벽체 높이 ${\Delta}h$기준으로 약 1.0~3.0h인 것으로 나타났다. 수평방향으로 전이되는 토압은 종횡비가 같을 때 수평방향 모두 동일한 높이에서 최대치를 나타내며, 종횡비가 증가함에 따라 토압의 최대 전이 지점이 벽체 하부에서 상부로 변화하였다. 수평방향 토압의 전이는 주동벽체 폭 w 기준으로 0.25w에서 56%~79%인 것으로 나타났으며, 연직방향 토압의 전이는 주동벽체 ${\Delta}h$기준으로 1.0~1.5h에서 50%~58%인 것으로 나타났다. 종횡비에 따라 전이되는 토압의 크기와 영향범위를 분석하고 주동변위 벽체 주변으로 전달되는 3차원 하중전이 분포도를 제시하였다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1702-1704
• /
• 2005

In solar power system, the height and azimuth of the sun are important parameters which control generated power magnitude. The way that controls the daily generation magnitude according to latitude and longitude and uses two axles is often used in the existing sunlight racing system now. In this two-axle sunlight track control system the self-load is concentrated on one FRAME. It is influenced of the regular load, snow load and the wind load, etc. It is difficult to set up the system in the building already built up. This research is a development about the small-scale economy track device of independent load-dispersing type solar generation system. The position track algorithm is through calculating the trail of height and azimuthal of the sun calculation to follow the sun.

• 한국지반공학회논문집
• /
• 제16권4호
• /
• pp.171-181
• /
• 2000

성토지지말뚝 상부의 성토지반내에서 발생되는 지반아칭효과에 의하여 성토하중이 말뚝에 전달되는 효과를 조사하면서 제안된 이론해석의 신뢰성을 확인하기 위하여 일련의 모형실험을 수행하였다. 본 모형실험에서 말뚝은 성토 아래에 일렬로 수열의 줄말뚝으로 설치하였으며, 말뚝캡보는 성토의 길이방향에 직각방향으로 말뚝두부에 설치하였다. 성토재의 하중전달에 가장 큰 영향을 미치는 요인으로는 말뚝캡보사이의 간격과 성토고를 들 수 있다. 이전의 이론적인 연구에 의해 제안된 지반아치의 반경보다 약 33%정도 큰 최소소요성토고보다 높게 성토를 실시할 경우 지반아치는 완벽하게 발생될 뿐만 아니라, 실험치와 이론치는 잘 일치함을 모형실험결과 확인할 수 있다. 모형말뚝캡보에 작용하는 성토하중의 분담률은 말뚝캡보사이의 간격이 증가함에 따라 감소하는 반면, 성토고가 높아짐에 따라 증가하였다. 따라서, 설계시 말뚝의 성토하중지지효과를 극대화시키기 위해서는 성토고를 충분히 높게한 상태에서 말뚝캡보의 간격비를 감소시켜야 한다. 여기서 말뚝캡보의 간격비를 감소시키려면 말뚝캡보사이의 간격을 감소시키거나 말뚝캡보의 폭을 증가시켜야 한다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2003년도 추계학술대회논문집
• /
• pp.121-124
• /
• 2003

A new form-joining process with the aid of an adhesive is proposed in which an epoxy adhesive is applied to a sheet metal pair, and before it cures the pair is clinched to cause the geometric constraint in the form of a protrusion. In order to reduce the forming load and the height of protrusions, a new die and punch set with a very small clearance was devised to reduce the depth of drawing and the forming load. Taguchi method was employed to find the optimal values of design parameters. To implement each case of the orthogonal array, the finite element method was used. The experiments showed that on the tensile-shear test, the bonding strength of the new form-joining process with an epoxy adhesive is approximately the same as that of the resistance spot welding; and in comparison with the other two form-joining processes with an epoxy adhesive, the height of protrusions was reduced by more than 65 percent and the forming load by 50 percent.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.181-186
• /
• 2002

A numerical analysis is undertaken to show the influence of bearing design parameters on the load capacity of air lubricated spiral grooved thrust bearing. The governing equation derived from the mass balance is solved by the finite difference method. Optimal values for various design parameters are obtained to maximize the load capacity. The design parameters are the groove angle, the groove width ratio, the groove height ratio, and the seal ratio.

• 한국초전도저온공학회:학술대회논문집
• /
• 한국초전도저온공학회 2003년도 학술대회 논문집
• /
• pp.178-181
• /
• 2003

Intermediate cooling for current lead is used of thermal link in conduction cooling and cooled of itself in liquid cooling because it is put in liquid. If a existing formula for cooling load and optimal diameter-length of current lead is applied, it generate some more cooling load. Therefore, variation of thermal link height and holding depth in liquid is considered. This result is used of reducing cooling load of current lead occupying most of superconducting system load and applying liquid/conduction cooling systems.

• 복합신소재구조학회 논문집
• /
• 제4권3호
• /
• pp.7-12
• /
• 2013

The demand for the structural system of reduction of story height increases because buildings are getting higher. The existing structural systems are not efficiency. Thus, it is hard to reduce the story height and existing methods cannot secure economics as expected. This study aims at developing the partially concrete-filled new type composite beam, which can efficiently resist against the end negative moment and central positive moment, also reduce deflection of beams. Through case studies on loading of concentrated load and uniformly distributed load to fixed beam, we could find the most efficient ratio of moment of inertia and the ratio ${\alpha}$(end beam length to span). The gap space between middle and end beam can be used as facilities installation, consequently the suggested Omega beam system is expected to get the effect of reduction in story height as well as reduction of quantity.

• 국제강구조저널
• /
• 제18권4호
• /
• pp.1252-1264
• /
• 2018

Long span bridges such as steel cable stayed and suspension bridges are usually more flexible than short to medium span bridges and expected to have large deformations. Deflections due to live load for long span bridges are important since it controls the overall heights of the bridge for securing the clearance under the bridge and serviceability for securing the comfort of passengers or pedestrians. In case of sea-crossing bridges, the clearance of bridges is determined considering the height of the ship master from the surface of the water, the trim of the ship, the psychological free space, the tide height, and live load deflection. In the design of bridges, live load deflection is limited to a certain value to minimize the vibrations. However, there are not much studies that consider the live load deflection and its effects for long span bridges. The purpose of this study is to investigate the suitability of live load deflection limit and its actual effects on serviceability of bridges for steel cable-stayed and suspension bridges. Analytical study is performed to calculate the natural frequencies and deflections by design live load. Results are compared with various design limits and related studies by Barker et al. (2011) and Saadeghvaziri et al. (2012). Two long span bridges are selected for the case study, Yi Sun-Sin grand bridge (suspension bridge, main span length = 1545 m) and Young-Hung grand bridge (cable stayed bridge, main span length = 240 m). Long-term measured deflection data by GNSS system are collected from Yi Sun-Sin grand bridge and compared with the theoretical values. Probability of exceedance against various deflection limits are calculated from probability distribution of 10-min maximum deflection. The results of the study on the limitation of live load deflection are expected to be useful reference for the design, the proper planning and deflection review of the long span bridges around the world.