• Architectural research
• /
• 제15권1호
• /
• pp.43-52
• /
• 2013

The reinforced concrete shear walls are being widely used in the domestic high-rise residential complex buildings. If designed by current codes, the special boundary element is needed in almost all high-rise shear wall buildings. This is because the equation for determining the provision of the special boundary element in the current codes cannot reflect the characteristics of the domestic high-rise shear walls with high axial load ratio and high proportion of elastic displacement to total displacement. In this study, a new equation to be able to reflect the characteristics is proposed. By using the equation, the special boundary element may not be necessary in certain cases so that structural engineers can relieve the burden of installing the special boundary element in every high-rise shear wall.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 추계 학술논문 발표대회
• /
• pp.184-185
• /
• 2014

The purpose of this study is to experimentally evaluate the variation characteristics of stiffness and impact resistance under the construction height of gypsum board wall at the actual construction site. The method suggested in previous study was applied on the test method of horizontal load resistance and impact resistance. As a result of horizontal load resistance test, when the wall height is 2,400 mm, the maximum displacement is 13.6 mm and residual deformation is 0.5 mm, and when the wall height is 3,000 mm, the maximum displacement is 31.3 mm and the residual displacement is 6.8 mm. As a result of impact resistance test, the residual deformation of each specimen at 20 cm of fall height were 1.02 mm and 0.08 mm, respectively, the residual deformation at 40 cm of fall height were 1.58 mm and 0.35 mm, respectively, and the residual deformation at 60 cm of fall height were 2.23 mm and 2.48 mm, respectively.

• 한국터널지하공간학회 논문집
• /
• 제18권5호
• /
• pp.487-497
• /
• 2016

터널을 굴착하면 굴진면 주변지반은 응력이 해방되고, 해방된 응력이 주변지반으로 재분배 되어 터널주변지반의 응력상태와 터널지보공에 작용하는 하중이 변한다. 굴진면에 변위가 발생하면 굴진면 전방지반이 이완되고 굴진면에 작용하는 토압은 감소하며, 변위가 일정한 크기 이상 커지면 굴진면 전방지반이 파괴상태에 이른다. 이때에 터널의 종방향으로 하중전이가 발생하며, 토피고나 굴진면의 변위정도에 따라 그 경향이 다르다. 굴진면 파괴에 따른 터널 종방향 하중전이에 대해서는 연구된 사례가 있으나, 굴진면 변위와 종방향 하중전이를 결부시켜서 연구한 사례는 거의 없는 실정이다. 따라서 본 연구에서는 토사터널에서 모형실험을 수행하여 굴진면이 과다변위로 인해 파괴됨에 따른 종방향 하중전이의 특성을 파악하였다. 즉, 정지토압 상태에서 시작하여 굴진면의 변위가 진행됨에 따른 터널 종방향 하중전이를 모형실험을 수행하여 측정하였다. 연구 결과, 종방향 하중전이는 굴진면 변위 초기에 대부분이 발생하고 굴진면 변위가 한계변위에 근접할수록 완만한 기울기로 한계치에 수렴하였다. 즉, 종방향 하중전이는 굴진면 전방지반이 아직 탄성상태일 때 급격히 증가하였고, 지반이 한계상태에 근접하면 완만하게 증가하는 경향을 나타내었다. 굴진면에서 변위에 의한 토압감소와 터널 종방향 하중전이는 같은 추세로 발생하는 것을 알 수 있었다.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1114-1119
• /
• 2010

Pile foundations have been used for upholding superstructure's loads. The researches on pile foundations subjected to compressive forces or horizontal loads have been actively carried out. However, recently, pile foundations, which are subjected to pull-out forces, are getting increased. The study on the pull-out resistance of piles becomes to be important. In addition, it is expected that belled piles will be used more and more, since the belled piles are effective to resist the pull-out forces. But there is still a lack of research on pull-out resistance of belled piles. Therefore, in order to investigate the resisting effect against pull-out of belled piles which is embedded in cohesionless soil. a series of pull-out test is performed on belled piles in field. Especially, the relation between load and displacement is analyzed through the pull-out test.

• 해양환경안전학회지
• /
• 제21권3호
• /
• pp.297-302
• /
• 2015

To prevent cargo accidents by repeated loads, a continuous monitoring for securing rope or additional safety measures are needed, but most of prevention measures have been conducted only by operator's own experience not a quantitative assessment. Hence, the Load-Displacement curve and approximation formula of securing rope were drawn in this research for a quantitative assessment and simplified measurement on a tension of securing rope using a tensiometer. Moreover, a com parison was conducted between m easuring tension and calculated tension on securing rope with portable tensiometer, 'Load-Displacement' approximation formula. The calculated tension of securing rope is obtained 153.3kfg using the formula and that result has not much difference with initial tension 150.0kgf. Lastly, an analysis of the characteristics of various ropes was suggested to enhance the reliability about quantitative assessment of securing rope's tension through further research.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 춘계학술대회 논문집
• /
• pp.1230-1235
• /
• 2011

The track stiffness is determined by the pad stiffness. Low elastic pad is the most effective track component on the basis of stress-displacement characteristics, dynamic response and fatigue characteristics. It is more important in case of concrete track. The main objective of this paper is to confirm the reduction effect of train load, which transfer to roadbed through track. To achieve this object, numerical analysis and real scale repeated loading test was performed. The load reduction effect of low elastic pad was analyzed by using displacement, stress and strain ratio of the paved track at each point.

• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.7-13
• /
• 2016

This paper presents the meter-out and meter-in speed control characteristics of a pneumatic cylinder with relief valve type cushion device. The piston displacement and velocity are measured to investigate high speed driving performance with variation of the pressure setting in relief valve, air supply pressure, load mass, the supply and exhaust flow rate from the cylinder. Also, the internal pressures and temperatures driving pressure and cushion chamber are measured. The piston displacements and velocities of meter-out and meter-in control are compared experimentally determined data. A comparison experimental data meter-out and meter-in control show that a relief valve type cushion device is suitable for high speed pneumatic cylinders. The desired response characteristics of piston displacement and velocity are satisfactory adjust the pressure setting of a relief valve with varying system parameters such as air supply pressure, load mass and controlled flow rate.

• Earthquakes and Structures
• /
• 제7권4호
• /
• pp.463-484
• /
• 2014

Solid piers with a rounded rectangular cross-section are widely used in railway bridges for high-speed trains in China. Compared to highway bridge piers, these railway bridge piers have a larger crosssection and less steel reinforcement. Existing material models cannot accurately predict the seismic behavior of this kind of railway bridge piers. This is because only a few parameters, such as axial load, longitudinal and transverse reinforcement, are taken into account. To enable a better understanding of the seismic behavior of this type of bridge pier, a simultaneous influence of the various parameters, i.e. ratio of height to thickness, axial load to concrete compressive strength ratio and longitudinal to transverse reinforcements, on the failure characteristics, hysteresis, skeleton curves, and displacement ductility were investigated. In total, nine model piers were tested under cyclic loading. The hysteretic response obtained from the experiments is compared with that obtained from numerical studies using existing material models. The experimental data shows that the hysteresis curves have significantly pinched characteristics that are associated with small longitudinal reinforcement ratios. The displacement ductility reduces with an increase in ratio of axial load to concrete compressive strength and longitudinal reinforcement ratio. The experimental results are largely in agreement with the numerical results obtained using Chang-Mander concrete model.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2003년도 추계학술대회
• /
• pp.41-46
• /
• 2003

The important problem in high speed spindles is to reduce and minimize the thermal effect by motor and bail bearings. Thermal characteristics according to the bearing pre-load and cooling condition are studied for the test spindl with grease lubrication and high frequency motor. Bearing and motor we main heat generation, and heat generation by ball bearings as a function of load, viscosity and gyroscopic moment effect are considered. Temperature distribution and thermal displacement according to the speed of spindle are measured by thermocouple and gap sensor. The results show that the fitting pre-load and cooling temperature are very effective to minimize the thermal effect by motor an ball bearings.

• 대한기계학회논문집A
• /
• 제34권6호
• /
• pp.701-708
• /
• 2010

면외평면전단하중과 면내전기하중을 받는 직교이방성 압전재료에서 전기투과형 전파균열장을 해석하였다. 압전재료에서 전파하는 균열의 운동방정식이 유도되었으며 근접해법을 통하여 응력장과 변위장의 해를 얻었다. 압전상수 및 유전율 등이 균열선단의 응력장과 변위장에 미치는 영향을 명확히 나타내었다. 본 연구에서 유도된 응력장과 변위장을 사용하여 압전재료에서 전파하는 균열선단부근의 응력과 변위의 특성에 대하여 논의하였다.