• 드라이브 ㆍ 컨트롤
• /
• 제18권1호
• /
• pp.17-23
• /
• 2021

The flow signal or spool position signal is used to determine the dynamic characteristics of directional control valves. Alternatively, the signal of spool position or flow can be replaced with the velocity of a low friction, low inertia actuator. In this study, the frequency response of the servo valve equipped with a spool position transducer is measured with a metering cylinder. The input signal, spool displacement, load pressure, and velocity of the metering cylinder are measured, and the theoretical results from the transfer function analysis are verified. The superposition rule for magnitude ratio and phase angle was found to be always applicable among any signal type, and it was found that the load pressure signal is not appropriate for use as the signal for measuring the frequency response of a servo valve. It was confirmed that the frequency response of a servo valve using metering cylinder was similar to the results from a spool displacement signal. The metering cylinder used for measuring the frequency response of a servo valve should be designed to have sufficiently greater bandwidth frequency than the bandwidth frequency of the servo valve.

• Smart Structures and Systems
• /
• 제28권6호
• /
• pp.827-838
• /
• 2021

The dynamic displacement is considered to be an important indicator of structural safety, and becomes an indispensable part of Structural Health Monitoring (SHM) system for high-speed railway bridges. This paper proposes an indirect strain based dynamic displacement reconstruction methodology for high-speed railway box girders. For the typical box girders under eccentric train load, the plane section assumption and elementary beam theory is no longer applicable due to the bend-torsion coupling effects. The monitored strain was decoupled into bend and torsion induced strain, pre-trained multi-output support vector regression (M-SVR) model was employed for such decoupling process considering the sensor layout cost and reconstruction accuracy. The decoupled strained based displacement could be reconstructed respectively using box girder plate element analysis and mode superposition principle. For the transformation modal matrix has a significant impact on the reconstructed displacement accuracy, the modal order would be optimized using particle swarm algorithm (PSO), aiming to minimize the ill conditioned degree of transformation modal matrix and the displacement reconstruction error. Numerical simulation and dynamic load testing results show that the reconstructed displacement was in good agreement with the simulated or measured results, which verifies the validity and accuracy of the algorithm proposed in this paper.

• Steel and Composite Structures
• /
• 제47권3호
• /
• pp.423-436
• /
• 2023

In this research, we tested 10 simply supported concrete-encased composite columns under monotonic eccentric loads and investigated their shear behaviour. The specimens tested were two reinforced concrete specimens, three steel-reinforced concrete (SRC) specimens with an H-shaped steel section (also called a beam section), and five SRC specimens with a cruciform-shaped steel section (also called a column section). The experimental variables included the transverse steel shape's depth and the longitudinal steel flange's width. Experimental observations indicated the following. (1) The ultimate load-carrying capacity was controlled by web compression failure, defined as a situation where the concrete within the diagonal strut's upper end was crushed. (2) The composite effect was strong before the crushing of the concrete outside the steel shape. (3) We adjusted the softened strut-and-tie SRC (SST-SRC) model to yield more accurate strength predictions than those obtained using the strength superposition method. (4) The MSST-SRC model can more reasonably predict shear strength at an initial concrete softening load point. The rationality of the MSST-SRC model was inferred by experimentally observing shear behaviour, including concrete crushing and the point of sharp variation in the shear strain.

• 한국강구조학회 논문집
• /
• 제12권2호통권45호
• /
• pp.151-165
• /
• 2000

교량에 통행하는 차량의 대형화와 통행교통량의 급격한 증가로 인하여 교량부재에서 피로손상이 많이 보고되고 있다. 교량부재의 피로손상을 방지하고, 안전을 유지하기 위해서 합리적인 피로조사를 실시하여야 한다. 교량의 피로설계에서는 차량 1대만 재하 시키는 방법을 채택하고 있으나, 실제 교량의 상부에 차량이 1대만 통과하는 일은 거의 없다. 통상 교량의 상부에는 복수의 차량이 동시에 재하되므로 합리적인 피로설계를 위해서는 동시재하의 영향을 고려하여야 한다. 본 논문에서는 도로교를 통행하는 차륜하중에 대해 선형중첩법과 교통류의 몬테카를로 시뮬레이션에 의한 변동응력해석을 실시하고, 피로 손상도를 구함으로써 통행차량의 차축하중에 대한 동시재하의 영향에 대해 연구하였다.

• 대한토목학회논문집
• /
• 제28권1A호
• /
• pp.95-104
• /
• 2008

본 연구에서는 경부고속철도상의 대표적인 교량인 2경간 연속보 형태의 고속철도 교량에 대하여 동적거동을 해석하고 공진발생의 감소방안들을 제시하였다. 하중은 한국형 고속철도하중인 총길이 380.15 m의 TGV-K 열차(2P+18T)가 일정한 속도로 이동하는 것으로 하였다. 동적거동을 모사하는 지배방정식은 질량과 강성이 분포된 연속계에서 만들어진 편미분방정식을 이용하여 구하였으며 Duhamel 적분을 이용한 모달계수의 처리를 수반하는 모드중첩법을 이용하여 동적해석을 수행하였다. 열차의 주행속도에 관계없이 동적거동을 급격히 감소시킬 수 있는 지간장이 존재하였으며 지금까지 연구된 단순보 형태의 교량에서 분석된 결과와는 달랐다. 열차의 주행속도에 의존하여 동적응답이 급격히 증가되어 공진현상을 일으키는 경우에도 공진을 감소시킬 수 있는 여러 방안들을 제시하였다.

• 한국지반공학회지:지반
• /
• 제7권4호
• /
• pp.35-48
• /
• 1991

본 논문에서는 원심모형실험 결과를 바탕으로 대상의 상재하중하의 보강토옹벽의 파괴 메카니즘에 관하여 연구를 실시하였다. 모형실험은 보강재의 재질, 길이, 배열을 변화시키면서 실시하였으며 보강재에 유발되는 인장력 을 측정하기 위하여 strain gauge를 부착하였다. 실험 결과를 분석하여 현재 사용되고 있는 설계 및 해석방법들과 비교함으로서 그들의 타당성 에 대한 검증을 실시하였다. 결론적으로 원심모형실험은 보강토옹벽의 거동을 연구하기 위한 매우 효과적인 방법이었다. 상 재하중하의 보강토옹벽의 극한 지지력을 산정하기 위한 2:1응력 분포법은 실험결과와 일치하였다. 뒷채움재의 자중과 상재하중에 의하여 보강재에 유발되는 인장력을 산정하기 위한 중첩법이 유효하다는 결론을 얻었다. 탄성이론을 사용하여 상재하중에 의해 보강재에 유발되는 최대 인장력을 산정한 결과 Boussinesq와 Westergaar해는 실험결과 보다 작게 산정된 반면에 Frohlich해는 실험결과와 일치하였다.

• Structural Engineering and Mechanics
• /
• 제44권2호
• /
• pp.127-138
• /
• 2012

The composite materials may be exposed to environmental (thermal or hygral or both) condition during their service life. The effect of environmental condition is usually adverse from the point of view of design of composite structures. In the present research study the effect of hygrothermal condition on the design of laminated composite structures is investigated. The active fiber composite (AFC) which may be utilized as actuator or sensor is considered in the present analysis. The sensor layer is used to sense the level of response of the composite structures. The sensed voltage is fed back to the actuator through the controller. In this study both displacement and velocity feedback controllers are employed to reduce the response of the composite laminate within acceptable limit. The Newmark direct time integration scheme is employed along with modal superposition method to improve the computational efficiency. It is observed from the numerical study that the laminated composite structures become weak in the presence of hygrothermal load. The response of the structure can be brought to the acceptable level once the AFC layer is activated through the feedback loop.

• Structural Engineering and Mechanics
• /
• 제23권3호
• /
• pp.233-247
• /
• 2006

Most codes of practice state that for large in-plane structures it is necessary to account for the spatial variability of earthquake ground motion. There are essentially three effects that contribute for this variation: (i) wave passage effect, due to finite propagation velocity; (ii) incoherence effect, due to differences in superposition of waves; and (iii) the local site amplification due to spatial variation in geological conditions. This paper discusses the procedures to be undertaken in the time domain analysis of a cable-stayed bridge under spatial variability of earthquake ground motion. The artificial synthesis of correlated displacements series that simulate the earthquake load is discussed first. Next, it is described the 3D model of the International Guadiana Bridge used for running tests with seismic analysis. A comparison of the effects produced by seismic waves with different apparent propagation velocities and different geological conditions is undertaken. The results in this study show that the differences between the analysis with and without spatial variability of earthquake ground motion can be important for some displacements and internal forces, especially those influenced by symmetric modes.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2006년도 춘계 학술발표회 논문집
• /
• pp.760-767
• /
• 2006

Underestimation of rock joint shear strength comes from an inadequate consideration of roughness mobilization behavior, which is changed by asperity size as well applied normal load. In this study, we performed rock joint shear tests, and studied the roughness mobilization characteristics related with the scale of normal stress and asperities. Test specimens with artificial triangular asperities were manufactured. The specimens consisted of 3 types, and each type represented unevenness, waviness and total roughness(superposition of unevenness and waviness). The experimental results show that the roughness mobilization characteristics are varied by the scale of normal stress and asperities. Furthermore, the investigation shows that the rate of geometrical component and mechanical component in the total roughness is also varied by the scale of normal stress and asperities. These results suggest that we should consider the roughness mobilization characteristics for the roughness quantification and the shear strength modelling.

• Tribology and Lubricants
• /
• 제10권3호
• /
• pp.62-70
• /
• 1994

An analytical model of the stress field caused by sliding indentation of brittle materials is developed. The complete stress field is treated as the superposition of applied normal and tangential forces with a sliding blister approximation of the localized inelastic deformation occuring just underneath the indenter. It is shown that lateral cracking is produced by the sliding blister stress field and that median cracking is caused by the applied contact forces. The model is combined with an experimental volume change measurements to show that the relative magnitude of tensile stresses governing lateral crack and median crack growth varies with the magnitude of the applied load. This prediction is consistent with the different regimes of experimentally observed cracking in soda-lime glass.