• 한국자동차공학회논문집
• /
• 제8권6호
• /
• pp.173-181
• /
• 2000

The stability of a structural plate is a crucial problem which causes wrinkling and buckling. In this paper, the effect of the pattern of spot-welding points in the two rectangular plate on the shear buckling load is studied with respect to the thickness, the aspect ratio of plates, the number of welding spots. Buckling coefficient of the simple plate was compared with that of two plates with various conditions to extract the effect of buckling strength. The effect of the number of welding spots are studied in two directions, longitudinal and transverse directions. The concluded that the reinforcement effect was maximized when the aspect ratio was close to 1.5 and that the effect of number of welding spots in longitudinal direction was larger than that in transverse direction.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.891-894
• /
• 2004

This paper estimate coefficient of adhesion through speed sensor-less vector control and load torque disturbance observer used for maximum tractive force control. And also proposes anti-slip control algorithm, which controls torque force of motor in order to keep the estimated adhesion force in maximum adhesion by controlling PI torque with the differential value of estimated adhesion force coefficient.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2008년도 추계학술발표대회 논문집
• /
• pp.75-80
• /
• 2008

Recently, Energy savings in buildings has received much attention in response to the increased needs for global warming and better comforts of the occupants in apartment housing. This study proposes the method which uses the sun control window film to reduce the cooling load and heating load improving the thermal performance of the building and it improves an energy efficiency. The film which used in actual measurement has a low shading coefficient and a solar energy transmission. so we measured the surface temperature of the triple Low-e glazing system used and inside temperature according to the change of outside temperature and solar energy to study thermal performance evaluation. As a result, it was helpful to use window film insulation to reduce inside temperature in summer and to keep room warm in winter.

• 콘크리트학회지
• /
• 제5권3호
• /
• pp.142-151
• /
• 1993

교량 구조물의 안전성(신뢰성) 평가는 중요한 작업으로서, 교량 구조물의 안전성은 부재 단면의 저항과부재에 작용하는 외부하중에 의해서 결정된다. 부재의 강도는 부재를 구성하는 재료의 강도, 부재의 치수 및 단면으 저항을 계산하는 산정식등에 내재하는 오차등으로 인해서 공칭저항과 실제값과는 많은 차이가 발생하며, 교량 구조물에서 발생하는 사하중 모멘트는 해석변수와 단면 자중에 의한 하중변수에 의해서 영향을 받는다. 본 연구에서는 사하중효과의 부재 저항의 확률특성을 결정하기 위한 신뢰성 연구를 수행하기 위해서 이들 기본변수들에 대한 확률특성을 실측 및 실험자료를 통해서 우선적으로 평가하였다. 이들을 구성하는 각 기본변수들의 확률특성은 기존 연구결과 및 본 연구의 현장 실측 자료를 hd해서 결정하였다. 본 연구의 교량의 안전도 평가 및 교량의 신뢰성 해석을 합리적으로 수행할 수 있는 유용한 토대를 제공하는 것으로 사료된다.

• Journal of Magnetics
• /
• 제20권4호
• /
• pp.421-426
• /
• 2015

This paper presents a practical method for estimation of average temperature in the permanent magnet (PM) of electric machine by using finite element analysis (FEA) and dynamo load experiment. First of all, the temperature effect of PM to the torque has been employed by FEA in order to evaluate the Temperature-Torque characteristic curve. The 1st order polynomial equation which is torque attenuation coefficient is derived by the FEA result of the Temperature-Torque curve. Next, torque saturation test with constant current condition is performed by dynamo load experiment. Then, the temperature trend can be estimated by adding the initial starting temperature using the torque attenuation coefficient and torque saturation curve. Lastly, estimated temperature is validated by infrared thermometer which measures temperature of PM surface. The comparison between the estimated result and experimental result gives a good agreement within a deviation of maximum $8^{\circ}C$.

• Journal of Advanced Marine Engineering and Technology
• /
• 제24권6호
• /
• pp.34-42
• /
• 2000

In this paper conventional technique will be described, which can be used for the measuring various parameters of induction motor. This is followed by presenting some other, alternative, techniques. The two tests are described which are suitable to obtain the electrical parameters of symmetrical 1hp three-phase squirrel-cage induction motor. These are the blocked rotor test and no load test. By the application of these, it is possible to determine the parameters which are presented in the steady-state equivalent-circuit of determining an induction motor. One conventional method of determining the inertia of an induction motors is obtained by performing retardation tests. The angular rotor speed of the motor is monitored, following its disconnection from the stator supply. Since the inertia torque J dw/dt contains the inertia coefficient J and the friction and windage torque Bw contains the coefficient B, then J and B can be determined by performing retardation tests.

• 한국농공학회:학술대회논문집
• /
• 한국농공학회 1999년도 Proceedings of the 1999 Annual Conference The Korean Society of Agricutural Engineers
• /
• pp.753-758
• /
• 1999

Concentration and discharge have been intensively monitored at the drainage canal in a paddy field area during storm-periods. Among 4 storm runoffs, the No. 2 and No. 3 runoff was in the fertilizer application period. The specific load-specific discharge equation L=aQ\ulcorner have different characteristics for the pollutants. The coefficient of b generally shows values of more than 1 for T-N, about 1 for COD\ulcorner, and less than 1 for T-P. For same specific discharge, No. 2 runoff shows higher specific load than other runoffs. For the coefficient of determination of the L-Q equation, COD\ulcorner is higher than T-N and T-P. The mean concentration of direct runoff, significantly depending on the storm events, is 0.6 to 8.3mg/ιfor T-N, 0.05 to 0.51 mg/ι for T-P, and 10.0 to 18.3 mg/ι for COD\ulcorner.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 2002년도 봄 학술발표회 논문집
• /
• pp.93-98
• /
• 2002

This study presents a new method to derive the constraint coefficient from the degree of angular deformation caused by welding, as measured experimentally by varying the shape of welded joints and the magnitude of constraints and from analysis results given by the elastic FEM method. The equivalent load was then calculated with this constraint coefficient. The validity of the numerical analysis involved in this new method was confirmed by its agreement with the experimental results. As for the effects of the constraints based on the shape of the welded joints in the case of Butt welding when the constraint coefficients are not considered, the deformed quantity produced by analysis is larger that produced by experiment and consequently is largely affected by the constraints.

• Tribology and Lubricants
• /
• 제24권5호
• /
• pp.234-240
• /
• 2008

It is well known that surface texturing improves the tribological properties of mechanical components for enhancing hydro-dynamic effect or serving as a micro reservoir. There are not, however, enough researches to reveal the effects of surface texturing on the tribological properties under grease lubrication which is used in lubricating many mechanical elements. In the present study, therefore, the effects of surface texturing on the tribological properties are investigated under grease lubrication based on an experimental approach. The results show that surface texturing decreases friction coefficient. It is found that the friction coefficient can be decreased by controlling the diameter and density of micro-dimple. The diameter of dimple is more effective under high load and low speed than otherwise. And, the density of dimple is effective under low load and high speed.

• Tribology and Lubricants
• /
• 제18권3호
• /
• pp.211-218
• /
• 2002

The effect of characteristic of surface roughness and roughness patterns on friction was studied experimentally in boundary lubrication with reciprocating tribometer. Roughness was changed from Ra=0.2($\mu\textrm{m}$)to Ra=1.2($\mu\textrm{m}$). Three roughness pattern-transverse, oblique, longitudinal- were tested for various load and velocity. The experimental results show that the scuffing resistance of surfaces with transversal roughness pattern is higher than that of surface with longitudinal and obliq pattern. under the conditions of the roughness values of Ra=0.2, 0.5,1.0 and 1.2. surfacer roughness (Ra) was decreased with the normal load increased before scuffing occurred. oblique pattern and longitudinal pattern with Ra=0.2 and Ra=1.0 was higher scuffing load under low sliding velocity, but with Ra=0.5 was higher scuffing load under high sliding velocity.