• Microbiology and Biotechnology Letters
• /
• v.26 no.4
• /
• pp.369-372
• /
• 1998

Microbial insecticide formulations were prepared by liquid and semi-solid fermentations using Bacillus thuringiensis subsp. kurstaki, HL-106 (BTK-HL106), B. thuringiensis subsp. israelensis HL-63 (BTI-HL63) and B. sphaericus 1593 (BS-1593) strains. The liquid fermentation medium contained molasses 2%, dextrose 1.5%, peptone 2%, D-xylose 0.025%, CaCl$_2$ 0.1%, K$_2$HPO$_4$ 0.1%, KH$_2$PO$_4$ 0.1%, MgSO$_4$$.$7H$_2$O 0.03%, FeSO$_4$$.$7H$_2$O 0.002%, ZnSO$_4$$.$7H$_2$O 0.02%. The composition of the semi-solid fermentation medium was rice bran 45.2%, zeolite 31%, yeast powder 0.02%, corn powder 5%, dextrose 3%, lime 0.3%, NaCl 0.06%, CaCl$_2$ 0.02%, and H$_2$O 15.42%. Insecticide formulations produced in the liquid fermentation named BTK-HL106, BTI-HL63 and BS-1593 pesticides and those in the semi-solid fermentation were designated as BTK-HL106-1, BTI-HL63-1 and BS-1593-1 pesticides, respectively. The number of spore (endotoxin crystals) was 2.65${\times}$10$\^$9/ spores per $m\ell$ in the BTK-HL106 and 3.5${\times}$10$\^$10/ in the BTK-HL106-1 3.8${\times}$10$\^$9/ spores in the BTI-HL63 and 7.0${\times}$10$\^$10/ in the BTI-HL63-1, and 7.5${\times}$10$\^$9/ in the BS-1593 and 1.4${\times}$10$\^$10/ in the BS-1593-1. The spores in the BS-1593 formulation was produced two times more than the other formulations. The spores in the BTI-HL63-1 were contained twice than those in the BTK-HL106-1, and five times than those in the BS-1593-1. The results indicated that spore (endotoxin crystals) productions in the semi-solid fermentation increased about ten times than those in the liquid fermentations. $LC_{50}$s of the BTI-HL63 and BS-1593 were 4.5 $\mu\textrm{g}$, and those of the BTI-HL63-1 and BS-1593-1 were 1.5 $\mu\textrm{g}$. $LC_{50}$ of the BTK-HL106 was 1.5 mg and that of the BTK-HL106-1 was 0.9 mg. The $LC_{50}$s of the formulations in the semi-solid fermentations showed about two to three times higher than those in the liquid fermentations.

• Applied Chemistry for Engineering
• /
• v.17 no.5
• /
• pp.509-516
• /
• 2006

The solid-liquid mass transfer coefficients $k_L$ in a gas-liquid-solid three phases agitated vessel were measured with conventional impellers (e.g. Rushton turbine, paddle, and propeller). For the conventional impellers the rotational speed for the complete suspension $N_{js}$ changes with the impeller height and gas flow rate. Mass transfer coefficient of the Rushton turbin impeller, for which the particle suspension was independent of the aeration, is correlated only with Pgv. Mass transfer coefficients $k_L$ for the Rushton turbine, paddle and propeller impellers were affected by the impeller position.

• Journal of Korea Foundry Society
• /
• v.28 no.3
• /
• pp.129-135
• /
• 2008

The reheating stage of electromagnetically stirred Al billet is a critical factor in the thixoforming process. When reheated to the solid-liquid state, the microstructure evolves to a more globular and more homogeneous structure by a coarsening mechanism, the kinetics depending on the initial microstructure. Microstructural evolution has been characterized by conventional parameters (mean size of particle and shape factor) as a function of holding time in the solid-liquid state. The aim of this study is to report experimental results concerning microstructural evolution in the solid-liquid state of electromagnetically stirred Al billet. The material was elaborated in the form of continuously cast bars solidified with electromagnetic stirring to degenerate the dendritic structure. The choice of the reheating conditions is determined by a dendritic ripening and coalescence mechanism, involving variations of both the shape and size of the particles. The reheating time has to be long enough to allow a minimum degree of spheroidizing, but has to be limited as much as possible in order to avoid excessive ripening. The optimum microstructure was obtained at the reheating temperature of near $584^{\circ}C$ and the holding time of 5 min. The only means of combining high productivity with good casting quality was to use feedstock billets whose microstructure showed rapid transformation characteristics.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2006.08a
• /
• pp.1711-1714
• /
• 2006

Anchoring energy of liquid crystals on solid substrates is a key parameter in liquid crystal technology. A nonperturbative method of its measurement by dynamic light scattering on thermal orientational fluctuations is presented, The ratio of the zenithal and azimuthal anchoring coefficients is shown to be equal to the ratio of the orientational elastic constants.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2003.07a
• /
• pp.1108-1111
• /
• 2003

We consider geometrical conditions of liquid crystals of bent-shape molecules that result in optically isotropic antiferroelectric structure that can be reversibly switched to birefringent states. An example of an ester based banana-shape substance is discussed that almost fulfills the ideal conditions and provides fast electro-optical switching with or without crossed polarizers.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.2 no.3
• /
• pp.219-230
• /
• 2004

Most of the low-level liquid radioactive wastes generated from PWR plants are classified into high or low total suspended solid(HTDS or LTDS), and into radiochemical and radioactive laundry waste. Although the evaporation process has a high decontami- nation ability, it has several problems such as corrosion, foam, and congestion. A new liquid waste disposal process using the ion-exchange demineralizer(IED), instead of the current evaporation process, has been introduced into the Yonggwang NPP #5 and 6. These two methods have been compared to understand the differences in this study. Aspects compared here were the released radioactivity amount of the liquid radioactive wastes, the dose of off-site residents, the decontamination factor, and the amount of the solid radioactive wastes. The IED system is designed to discharge higher radioactivity about 20% than the evaporating system, and the actual radioactivity released from the evaporating and IED system were 0.473mCi and 1.098mCi, respectively. The radioactivity released from the IED was 2.32 times higher than that of the evaporating system. The dose of off-site residents was $2.97{\times}10^{-6}$mSv for the evaporating system, and $6.47{\times}10^{-6}$mSv for IED. The decontamination factor(DF) of the evaporator is, in most cases, far lower than the lower limits of detection(LLD) with the Ge-Li detector. Due to the low concentration of the liquid wastes collected from the liquid waste system, the decontamination factor of IED is very low. Since there is not enough data on the amount of solid radioactive wastes generated by the evaporation system, the comparison on these two systems has been conducted on the basis of the design, and the comparison result was that the evaporating system generated more wastes about 40% than IED.

• Archives of Pharmacal Research
• /
• v.26 no.2
• /
• pp.162-167
• /
• 2003

Liquid suppository systems composed of poloxamers and bioadhesive polymers were easy to administer to the anus and mucoadhesive to the rectal tissues without leakage after the dose. However, a liquid suppository containing diclofenac sodium could not be developed using bioadhesive polymers. since the drug was precipitated in this preparation. To develop a liquid suppository system using sodium chloride instead of bioadhesive polymers, the physicochemical properties such as gelation temperature, gel strength and bioadhesive force of various formulations composed of diclofenac sodium, poloxamers and sodium chloride were investigated. Furthermore, the pharmacokinetic study of diclofenac sodium delivered by the liquid suppository was performed. Diclofenac sodium significantly increased the gelation temperature and weakened the gel strength and bioadhesive force, while sodium chloride did the opposite. The liquid suppositories with less than 1.0％ of sodium chloride, in which the drug was not precipitated, were inserted into the rectum without difficulty and leakage. Furthermore, liquid suppository gave significantly higher initial plasma concentrations and faster Tmax of diclofenac sodium than did solid suppository, indicating that drug from liquid suppository could be absorbed faster than that from solid one in rats. Our results suggested that a thermosensitive liquid suppository system with sodium chloride and poloxamers was a more physically stable, convenient and effective rectal dosage form for diclofenac sodium.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2008.03a
• /
• pp.283-292
• /
• 2008

The foremost criterion in the design of a Satellite Launch Vehicle(SLV) is its performance capability to boost the designated payload to the desired mission orbit; it starts from focusing on the SLV configuration to achieve the velocity requirements($}\Delta}V$) for the mission. In this paper we review an analytical approach which is suitable enough for preliminary conceptual design and is used previously to optimize stage configurations for Two Stage to Orbit SLV for Low Earth Orbit(LEO) Missions; we have extended this approach to Three Stage to Orbit SLV and compared different propellant options for the mission. The objective is to minimize the Gross Lift off Weight(GLOW). The primary performance figures of merit were the total inert weight of the SLV and the payload weight that the SLV could lift into LEO, given candidate propulsion systems. The optimization is achieved by configuring the $}\Delta}V$ between stages. A comparison of configurations of single-stage and multi-stage SLVs is made for different propellants. Based upon the optimized stage configurations a comparative performance analysis is made between Liquid and Solid fueled SLV. A 3 degree of freedom trajectory-analysis program is modeled in SIMULINK and used to conduct the performance analysis. Furthermore, a cost analysis is performed on our stage optimized SLVs. The cost estimation relationships(CER) used give us a comparison of development and fabrication costs for the Liquid vs. Solid fueled SLV in man years. The pros and cons of the production, operation ability, performance, responsiveness, logistics, price, shelf life, storage etc of both Solid and Liquid fueled SLVs are discussed. The statistics and data are used from existing or historical(real) SLV stages.

• Journal of Advanced Engineering and Technology
• /
• v.4 no.4
• /
• pp.431-436
• /
• 2011

This study was carried out to reduce the problem during distillation process, which separate U, TRU (TRans Uranium) metal electro deposit, Cd and LiCl-KCl eutectic salt generating from LCC (Liquid Cadmium Cathode) electro winning process. The cadmium recovering apparatus was manufactured to separate for each metal using solid-liquid separation method. The apparatus consists of the first sieve for the separation of U and TRU metal electrodeposit, the second sieve for the separation of LiCl-KCl eutectic salt, cadmium collection basket, and a heating furnace. In addition, the size of each sieve is 2 mm to 3 mm. In this experiment, a metal wire was employed to replace TRU metal electrodeposit and U, which exist actually in a LCC crucible. In the solid state, The LiCl-KCl is separated at 340℃ at which the solid and the liquid of the remaining cadmium and LiCl-KCl eutectic salt coexists in each, after the metal wire separated at 500℃. As a result, it seems that it would be beneficial to set the processing condition in the distillation process with the additional treatment process of cadmium and LiCl-KCl eutectic salt.

• Journal of Welding and Joining
• /
• v.15 no.4
• /
• pp.136-142
• /
• 1997

In this study, the amorphous foil filler, thickness of 20 - $20~30\mu\textrm{m}$ was made to develop Cu-7.5wt%Mn-7.5wt%Si insert alloy(melting point temperature : solidus line 1003K, liquidus line 1070K). Liquid phase diffusion bonding of 304 stainless steels (STS304), is carried out successfully by using developed Cu-7.5Mn-7.5Si insert alloy. Bonding conditions are taken from bonding pressure of 5MPa, bonding temperatures from 1073K to 1423K varied within 50K and brazing holding times of 0, 30, 60 and 240 minutes. As the results, the tensile strength in the liquid phase diffusion bonding is a little bit lower than that in the solid phase diffusion bonding. The authors find out that the liquid phase diffusion bonding needs lower bonding pressure than the others. Therefore, the liquid phase diffusion bonding had an excellent brazability in which the bonding process showed the typical mechanism of diffusion bonding. In corresponding, the new developed insert alloy of low melting pointed Cu-7.5Mn-7.5Si makes possible brazing between the STS304.