• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2005.11a
• /
• pp.177-183
• /
• 2005

In this work, Inconel 600, Inconel 625 and Haynes 230 are welding using Nd:YAG laser and electron bear. These heat-resistant alloys are typically used for the liquid thruster. To examine, the affects of experimental parameters on weld ability, the plate welding of these materials were carried out using both Nd:YAG laser and electron bear. Also, the micro-structure, micro-hardness, and tensile strength of the specimens were analyzed. from the analysis of the experimental results of laser and electron beam welding, we have obtained the optimal welding conditions.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.4
• /
• pp.1-11
• /
• 1999

Thermal behavior of spacecraft propulsion system utilizing monopropellant hydrazine ($N_2$$H_4$) is addressed in this paper. Thermal control performance to prevent propellant freezing in spacecraft-operational orbit was test-verified under simulated on-orbit environment. The on-orbit environment was thermally achieved in space-simulation chamber and by the absorbed-heat flux method that implements an artificial heating through to the spacecraft bus panels enclosing the propulsion system. Test results obtained in terms of temperature history of propulsion components are presented and reduced into duty cycles of the avionics heaters which are dedicated to thermal control of those components. The duty cycles are subsequently converted into the electrical power required in the operational orbit. Additionally, cyclic temperature of each component, which was made under thermal-balanced condition of spacecraft, is compared to the acceptable design range and justified from the viewpoint of system verification.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.6
• /
• pp.103-120
• /
• 2010

A development history of the thrusters used for space-vehicle orbit maneuver/attitude control is reviewed with their performance characteristics. Especially, a scrutiny is made for the current and practical application of TVC/Gimbal/Thrusters to the roll/pitch/yaw-axis control of each stage of launch vehicles. It is well perceived that a precise 3-axis attitude control system (ACS) must be equipped on the final stage of space launch vehicles (SLV) for an attainment of orbit-insertion accuracy. Under the superior reliability as well as moderate performance features, the monopropellant hydrazine thrusters occupy most of the SLV's 3-axis ACS currently operated. Domestic development status of the medium-thrust-level thruster is shortly introduced, finally.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.341-347
• /
• 2011

This work studies the performance of an injector for a monopropellant thruster, comparing a conventional and new injector types. The conventional injector consists of 8 nozzles on a convex surface allowing the jet to be diverged. The new injector, we suggested, is an impinging type with nozzle holes on a concave surface. The fuel streams through the nozzle holes are collide at a point on an axial direction, which allow to atomize the liquid streams and to spray more uniformly along circular direction. The performance of the injectors is investigated by using computational fluid dynamics, particle image velocimetry and high speed camera visualization.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.05a
• /
• pp.23-27
• /
• 2006

Brazing Failure has been occurred in the process of thrust chamber assembly. The possible factors have been analyzed by sample tests. The actual causes of 'Overflow' phenomenon have been investigated horn Brazing Material and fabrication of Piece Parts. The rejection rate of process has been improved by appling this results to a real brazing process.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2003.05a
• /
• pp.189-192
• /
• 2003

This paper summarizes a satellite program-specific performance requirements and test results for the verification of standard mono-propellant hydrazine thruster (MRE-1) producing 0.95 lbf (4.2 Newtons) nominal steady-state thrust at an inlet pressure of 350 psia (2.41 Mpa). Performance characteristics are shown in terms of thrust behavior at steady state and pulse mode firing. Hot firing test philosophy is briefly introduced, too.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2011.04a
• /
• pp.85-88
• /
• 2011

In the trend of world wide environment preservation, researchers tried to find new environment friendly propellant instead of highly toxic propellant, Hydrazine. Among the candidates, ionic liquid propellants have lower toxicity, higher density, and higher specific impulse than Hydrazine. These ionic liquid propellants have high combustion chamber temperature, so catalyst supports such as gamma alumina cannot withstand in that temperature. Therefore, a catalyst that showed stable characteristic in high temperature is needed. Barium dopped alumina can be changed to Hexaaluminate in high temperature, and its characteristic in high temperature is superior than gamma alumina. Barium dopped Alumina is wet impregnated with Platinum and heated up to $1300^{\circ}C$ and $1400^{\circ}C$ for 2 hours. Those catalysts were examined by XRD, SEM, EDS, BET, and Drop test.

• Aerospace Engineering and Technology
• /
• v.3 no.1
• /
• pp.97-102
• /
• 2004

Propulsion System provides the required velocity change impulse for orbit transfer from parking orbit to mission orbit and three-axis vehicle attitude control impulse. KOMPSAT-2 propulsion system(PS) is an all-welded, monopropellant hydrazine system. The PS consists of the subassemblies and components such as Thrusters, Propellant Tank, Pressure Transducer, Propellant Filter, Latching Isolation Valves, Fill/Drain Valves, interconnecting propellant line assembly, and thermal hardwares for operation-environment control of the PS. This paper summarizes a development process of the liquid propulsion system from the design engineering up to the test and evaluation.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.8 no.4
• /
• pp.84-90
• /
• 2004

A performance evaluation is made in terms of thrust, impulse bit. and specific impulses for a set of mono-propellant hydrazine thrusters producing 0.95 lbf of nominal thrust at an inlet pressure of 350 psia. With a brief description on the hot-firing test configuration and procedures. a typical data obtained from steady-state firing mode is given directly showing the variational behavior of propellant supply pressure, mass flow rate, vacuum condition, and thrust. The performance features are successfully compared to the reference criteria of 1-lbf standard mono-propellant rocket engine. Additionally. a statistical inter-thruster treatment is concisely depicted for the justification of selected thrusters as a grouped member of flight model for spacecraft propulsion system.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.978-983
• /
• 2017

Ammonium dinitramide(ADN) is currently under inder investigation as a replacement for ammonium perchlorate, both for environmental and toxicological reasons. Another promising application is ADN-based liquid monopropellant as a replacement for hydarzine, which is highly toxic and carcinogenic. Production of ADN is today normally performed via guanylurea dinitramide(GUDN) by reaction with potassium hydroxide to yiela potassium dinitramide(KDN). In a second reaction step, KDN is reacted with ammonium sulfate to give ADN. In our new improved process, ADN is synthesized from GUDN in one single reaction step. The simplified process improves purity, reduces the amount of by-products and allows production of ADN at a potentially lower cost, which is crucial to favour the use of ADN.