• Proceedings of the KIEE Conference
• /
• 1995.07b
• /
• pp.509-512
• /
• 1995

The relaying algorithm to calculate the fault distance from only transient signal at faults in T/L is presented. In this paper. At faults the oscillation frequency components exist in both voltage and current and these components minimize the input impedance shown in fault point. The equivalent source impedance shown in relaying point is needed to calculate the fault distance using these components. To source impedance, the reflection coefficient between forward wave and backward and the Prony's analysis is also employed to extract the oscillation frequency component from transient signals. The case study show that the new distance relaying algorithm satisfies the high operation speed and high accuracy even if the algorithm uses only transient signals.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.29A no.3
• /
• pp.25-32
• /
• 1992

In UHF, VHF new design method of samll-sized 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance using both lumped elements and distributed elements is presented. At the center frequency of 900 MHz, 3-dB 0$^{\circ}$/180$^{\circ}$ ring hybrid terminated arbitrary impedance is designed, analyzed and tested. Good agreements are obtained between measured and theoretical modeling results, and at the same time, the circuit area of hybrid fabricated with two dimensional parallel coupled line, distributed elements and lumped elements is reduced by more than 70% compared with only distribyted-type circuits.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.8 no.5
• /
• pp.98-104
• /
• 2009

In this paper, improved VCO(voltage controlled oscillator) with push-push structure and high impedance-inverter is designed and implemented. Two harmonic oscillators are combined into push-push structure. As a result, the fundamental suppression and the output power have been progressed. For the improved coupling characteristics between hair-pin resonator and two parallel microstrip line using high impedance inverter, the phase noise has been suppressed.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.73-77
• /
• 2018

This paper proposes a dual-band bandpass filter using stepped-impedance resonators (SIRs) with parallel coupled structures. The proposed filter adopts U-shaped SIRs with parallel coupled lines (PCLs) that have interdigital and comb-line shorted ends. The central PCLs build an upper passband and a transmission zero, and the two U-shaped SIRs build a lower passband. Four resonators and coupling structures are theoretically analyzed to derive its scattering parameters. A novel dual-band bandpass filter is designed and fabricated using the induced scattering characteristics. The measured results show that the fabricated dual-band bandpass filter has an insertion loss of less than 1.02 dB in the lower band of 2.45 GHz and of 3.01 dB in the upper band of 3.42 GHz, and a band-to-band isolation of more than 40 dB, from 3.14 to 3.2 GHz.

• Journal of electromagnetic engineering and science
• /
• v.18 no.2
• /
• pp.101-107
• /
• 2018

The impedance bandwidth and radiation characteristics of an aperture-coupled microstrip line-fed patch antenna (ACMPA) with a high permittivity (${\varepsilon}_r=10$) feed substrate suitable for integration with a monolithic microwave integrated circuit (MMIC) are investigated for various feed substrate thicknesses through an experiment and computer simulation. The impedance bandwidth of an ACMPA with a high permittivity feed substrate increases as the feed substrate thickness decreases. Furthermore, the front-to-back ratio of an ACMPA with a high permittivity feed substrate increases and the cross-polarization level decreases as the feed substrate thickness decreases. As the impedance bandwidth of an ACMPA with a high permittivity feed substrate increases and its radiation characteristics improve as the feed substrate thickness decreases, the ACMPA configuration becomes suitable for integration with an MMIC.

• Journal of The Institute of Information and Telecommunication Facilities Engineering
• /
• v.9 no.2
• /
• pp.35-41
• /
• 2010

The balance coefficients between telecommunication lines are specified in the technical standard and the power induction computation method varies in the order of 100 times in magnitude according to the amount of impedance. The results of actual balance measurements, differing from time to time with the measurement circuit or increasing proportionally as the induction voltage increases, appeared as a measurement error because of not using the standard measurement circuit. This article investigates such errors and proposes the use of a standard balance measurement circuit and a measurement device impedance under the domestic notification standard and the ITU-T international standard.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.328-329
• /
• 2020

The AC/DC converter, which connects the AC grid to the DC grid in the microgrid, is a critical component in power sharing and stable operation. Sometimes the AC/DC converters are connected in parallel to increase the transmission and reception capacity. When connected in parallel, circulating current is generated due to line impedance difference or sensor error. As a result of circulating current, there is deterioration and loss in particular PCS(Power Conversion System). In this paper, we propose droop control with novel adaptive virtual impedance for reducing circulating current. Feasibility of proposed algorithm is verified by PowerSIM simulation.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.7
• /
• pp.750-755
• /
• 2003

This paper proposes a new three-line balun. The equivalent circuit of the proposed three-line balun is presented, and impedance matrix［Z］of the equivalent circuit is derived from the relationship between the current and voltage at each port. The design equation for a given set of balun impedance at input and output ports is presented using［S］parameters, which is transferred fom impedance matrix,［Z］. To demonstrate the feasibility and validity of design equation, multi-layer ceramic(MLC) chip balun operated in the 2.4 GHz ISM band frequency is designed and fabricated by the use of the low temperature co-fired ceramic(LTCC) technology. By employing both the proposed new three-line balun equivalent circuit and multi-layer configuration provided by LTCC technology, the 2012 size MLC balun is realized. Measured results of the multi-layer LTCC three-line balun match well with the full-wave electromagnetic simulation results, and measured in band-phase and amplitude balances over a wide bandwidth are excellent. This proposed balun is very easily applicable to multi-layer structure using LTCC as shown in the paper, and also can be realized with microstrip lines on PCB. This distinctive performance is very favorable for wireless communication systems such as wireless LAN(Local Area Network) and Bluetooth applications.

• Proceedings of the KIPE Conference
• /
• 1997.07a
• /
• pp.211-215
• /
• 1997

Localized communication networks for office automation, security monitoring, environmental management of buildings, computer communications, and other applications enjoy every increasing demand. This paper proposes a direct sequence spread spectrum communication system for use in power line data transmission. Advantages of power distribution circuits include reasonably universal coverage and easy access vis a standard wall plug. Disadvantages include limited communication bandwidth, relatively high noise levels, and varying levels of impedance, noise, and attenuation. Spread spectrum signalling provides immunity to narrow-band signal impairments and multiplexing capability. Our prototype power line communication module supports completely physical and data link layers based on the international standard ISO 10368 for reliable high-speed power line communication system. Moreover it provides useful functions to compose a plant monitoring and control system. All the circuits of the communication module are included in one compact circuit. Thus a functional communication system for the power line plant monitoring and control is implemented.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4A
• /
• pp.232-237
• /
• 2003

We present the derivation of the loci of the reflection coefficient of a loaded transmission line on the Smith chart as the length of the transmission line is varied. The results show that the loci constitute a circle when the characteristic impedance of the transmission line differs from the normalizing one, whose center and radius are determined by the impedances of the load and the transmission line. The results can be used in the matching circuit design using microstriplines when line width and length should be compromised.