• 한국강구조학회 논문집
• /
• 제22권6호
• /
• pp.581-588
• /
• 2010

최근 강구조 건축물에 대한 상온 및 화재 시의 구조거동에 관한 요구사항이 증대되는 추세에 있으며, 내화구조에 관한 요구조건을 충족시키기 위해서는 내화설계가 요구된다. 내화설계에는 법규, 기준 등에 따라 평가되는 시방적 내화설계와 화재 발생 시 구조물 거동을 평가하는 성능기반 공학적 내화설계로 대별된다. 현재 성능기반 공학적 내화설계는 세계적인 추세로 활발히 적용되고 있으나, 국내에서는 아직 적용되지 못하는 실정이다. 따라서 본 논문에서는 성능 기반 공학적 내화설계의 지침 마련의 기반자료 확보를 위하여 H-형강 보부재와 H형강의 웨브에 콘크리트로 충전된 보부재를 대상으로 한계온도 설정을 목적으로 한다. 재하가열시험을 통하여 H-형강 보부재의 한계온도를 도출하였고, 한계온도는 적용 하중비에 좌우되는 것을 확인하였다. H-형강 웨브에 콘크리트가 충전된 하중비 80%, 60% 및 50%의 시험체는 모두 3시간의 내화성능을 보였다.

• 토지주택연구
• /
• 제3권3호
• /
• pp.279-286
• /
• 2012

뢰성에 기반한 한계상태설계법은 국제표준화기구인 ISO뿐만 아니라 국내의 각종 건설관련 기준에서도 적용되는 등 국내외적으로 기존 허용응력설계법을 대체하고 있는 실정이다. 본 논문에서는 국내에서 건축물의 기초로 많이 사용되고 있는 PHC 매입말뚝을 대상으로 한계상태설계법의 일종인 LRFD 설계정수를 제안하였다. PHC 매입말뚝의 LRFD 설계정수를 제안하기 위해 81개의 현장 동재하 시험자료와 이들 말뚝에 대한 지지력 설계(Meyerhof 설계법, SPT-CPT 전환 설계법) 자료를 분석하고 목표 신뢰도 지수 2.33과 3.0에 대해 하중저항계수를 제시하였다. PHC 매입말뚝의 저항계수는 목표 신뢰도 지수에 따라 Meyerhof 방법, SPT-CPT 전환법은 각각 0.36~0.44, 0.24~0.31을 나타내었다.

• 한국철도학회논문집
• /
• 제19권2호
• /
• pp.187-194
• /
• 2016

철도교량의 신뢰도 기반 한계상태설계법 도입 시 목표신뢰도지수 산정을 위하여 기존 철도교량의 신뢰도지수 산정이 선행되어야 한다. 대표적인 복선 철도교량 중 하나인 6주형 PSC-I형 거더교량에 대해 신뢰도지수를 산정하였다. 최외측 거더의 휨모멘트에 대한 신뢰도 해석을 수행하였다. 휨저항강도 및 고정하중효과는 도로교 한계상태설계법 도입 시 적용된 선행연구자들의 평균과 변동계수를 활용하였고, 열차의 활하중 효과는 여객/화물 혼용선 중 중량화차 통행이 빈번한 중앙선에서 현장계측 데이터를 활용하였다. 한계상태방정식에 대하여 개선된 일계이차 모멘트법(AFOSM)으로 신뢰도 분석을 수행하였으며, 하중효과와 저항효과의 각 요소가 신뢰도지수에 미치는 민감도를 분석하여 중요도를 검토하였다.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2000년도 하계종합학술대회 논문집(3)
• /
• pp.105-108
• /
• 2000

As Internet and WWW grow rapidly, the role of web servers is getting more important, and the number of users in a few popular site is also explosively increasing. Load balancing in clustered web server systems is important task to utilize whole system effectively, so dynamic load balancing is required to overcome the limit of static load balancing. In this paper, we propose two dynamic load balancing schemes, and analyzed load model and Performance improvement and also compare existing load balancing methods and IP filtering method. In case of load balancing with threshold, little extra traffic was required for better performance, but in case of load balancing with load weight, we found that the performance mainly depends on information exchange rate.

• Geomechanics and Engineering
• /
• 제18권3호
• /
• pp.315-328
• /
• 2019

This paper presents an investigation on bearing capacity, load-settlement behavior and safety factor of rock-soil slopes reinforced using geogrid-box method (GBM). To this end, small-scale laboratory studies were carried out to study the load-settlement response of a circular footing resting on unreinforced and reinforced rock-soil slopes. Several parameters including unit weight of rock-soil materials (loose- and dense-packing modes), slope height, location of footing relative to the slope crest, and geogrid tensile strength were studied. A series of finite element analysis were conducted using ABAQUS software to predict the bearing capacity behavior of slopes. Limit equilibrium and finite element analysis were also performed using commercially available software SLIDE and ABAQUS, respectively to calculate the safety factor. It was found that stabilization of rock-soil slopes using GBM significantly improves the bearing capacity and settlement behavior of slopes. It was established that, the displacement contours in the dense-packing mode distribute in a broader and deeper area as compared with the loose-packing mode, which results in higher ultimate bearing load. Moreover, it was found that in the loose-packing mode an increase in the vertical pressure load is accompanied with an increase in the soil settlement, while in the dense-packing mode the load-settlement curves show a pronounced peak. Comparison of bearing capacity ratios for the dense- and loose-packing modes demonstrated that the maximum benefit of GBM is achieved for rock-soil slopes in loose-packing mode. It was also found that by increasing the slope height, both the initial stiffness and the bearing load decreases. The results indicated a significant increase in the ultimate bearing load as the distance of the footing to the slope crest increases. For all the cases, a good agreement between the laboratory and numerical results was observed.

• 한국정밀공학회지
• /
• 제18권6호
• /
• pp.133-140
• /
• 2001

This paper suggests another system for a cutting force measuring tool in a milling process. Generally, tool dynamometer is taken into account for the most appropriate cutting force measuring tool in the analysis of cutting mechanism. However, high price and limited space make it difficult to be in-situ system for controllable milling process. Although an alternative method using AC current of servo-motor has been suggested, it is unsuitable for cutting force control because of small upper frequency limit and noise. The cutting force measuring system is composed of two load cells placed between the moving table bracket and the nut flange part of ballscrew. It has many advantages such as low cost and wide range measurement than tool dynamometer because of the built-in moving table and the low cost load cell. The static and dynamic model of the measuring system using imbeded load cell is introduced. Various Experiments are carried out to validate both models. By comparing the cutting forces from a series of end milling experiments on the tool dynamometer and the system developed in this paper, the accuracy of the cutting force measuring system is verified. Upper frequency limit is measured by the experiment of dynamic characteristics.

• 한국강구조학회 논문집
• /
• 제27권4호
• /
• pp.387-397
• /
• 2015

국내의 내화성능평가는 대부분 사양적설계 방법인 품질시험을 통해 이뤄지고 있다. 하지만 시험 특성상 많은 비용과 시간을 요구하며 다양한 건축구조에 대한 내화성능평가에는 어려움이 많다. 따라서 본연구에서는 성능적 설계를 위한 연구로 유한요소 구조해석 프로그램인 ABAQUS를 사용해 H형강 휨재를 대상으로 변수에 따른 열응력 해석을 통해 내화성능을 검토하며, 하중비별 한계온도를 제안한다.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2009년도 춘계학술대회
• /
• pp.413-421
• /
• 2009

This paper investigates tensile characteristics of the stress aging heat-treated SM45C steel which are aging temperature at $250^{\circ}C$, $300^{\circ}C$, aging time at 1, 3 hours, and applied load at 300, 400N conditions by using acoustic emission. Most suitable aging condition was aging temperature $300^{\circ}C$, aging time 1 hour, and aging applied load 300N. And increased yield load 28.3% than non-treatment specimen in this condition. AE energy in elastic limit increased about 16.7 times than non-treatment specimen. When aging time is 3 hours, yield load decreased than other conditions that possibility is high to have itself defect on inside the specimen or coarse grain size precipitation is different in happened over-aging phenomenon. Especially, in case of $300^{\circ}C$, 3 hours and 400N condition appeared AE energy in elastic limit fairly high about 30 times than non-treatment specimen. This is considered by emit a lot of energies when material causes plastic deformation because the ductility increases on specimen by over-aging phenomenon.

• 한국공간구조학회논문집
• /
• 제4권3호
• /
• pp.103-109
• /
• 2004

본 논문은 조합하중을 받는 공간구조물의 안정경계를 파악하는 것이다. 구조물에 작용하는 독립된 여러 가지 하중벡터는 기본이 되는 하중 모드와 하중매개 변수를 이용하여 나타내고, 독립된 하중 매개변수에는 비례관계를 설정함으로서 하나의 하중변수에 의해 하중을 부여한다. 구조물의 좌굴하중 즉 임계점은 평형조건이 불안정이 되는 극한점과 분기점으로 분류되고, 가장 낮은 하중이 좌굴하중으로 정의된다. 본 논문에서는 기하학적 비선형 문제를 해석하기 위한 수치해석법으로는 호장법과 뉴턴-랩슨법을 이용하였으며, 본 해석을 통하여 안정경계를 파악함은 물론 좌굴모드 및 좌굴하중을 명확히 규명하였다.