• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.32 no.5
• /
• pp.411-418
• /
• 2008

In this work, the effect of strength mismatch on plastic limit loads is quantified for similar metal weld plates with cracks under tension load, via three-dimensional, small strain elastic-perfectly plastic finite element analyses. Relevant variables related to plate geometry and crack length are systematically varied, in addition to the weld width. An important finding is that mis-match limit loads can be uniquely quantified through strength mis-match ratio and one geometry-related parameter. Based on the proposed limit load solutions, reference stress based J-integral estimates is also investigated. When the reference stress is defined by the mis-match limit load, predicted J-integral values agree overall well with FE results.

• Special Issue of the Society of Naval Architects of Korea
• /
• 2015.09a
• /
• pp.69-73
• /
• 2015

An evaluation of the accidental limit state (ALS) for design of a semi-submersible drilling rig is one of the essential design requirements as well as ultimate limit state (ULS) and fatigue limit state (FLS). This paper describes the ALS evaluation on the explosion accident at shale shaker room of semi-submersible drilling rig. There are three steps for the ALS evaluation such as structural analysis at concept design, risk based safety design and structural analysis at detailed design. For the ALS evaluation at concept design, conceptual explosion overpressure from the Rule guided by the classification society was used in the structural analysis that was carried out using LS-DYNA. To set up the design accidental load (DAL), explosion analysis was carried out using FLACS taking safety barriers into consideration. Then, the structural analysis was carried out applying DAL for the ALS evaluation at detailed design. Through the ALS evaluation on the explosion at shale shaker room, the importance of the risk based safety design was described.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.26 no.3
• /
• pp.183-189
• /
• 2013

In this paper, uncertainties and failure criteria of structure are mathematically expressed by random variables and a limit state equation. A limit state equation is approximated by Fleishman's 3rd order polynomials and the theoretical moments of an approximated limit state equation are calculated. Fleishman introduced a 3rd order polynomial in terms of only standard normal distiribution random variables. But, in this paper, Fleishman's polynomial is extended to various random variables including beta, gamma, uniform distributions. Cumulants and a normalized limit state equation are used to calculate a theoretical moments of a limit state equation. A cumulative distribution function of a normalized limit state equation is approximated by a Pearson system.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.12 no.7
• /
• pp.527-533
• /
• 2002

A railway vehicle should be satisfied with the safety criteria and ride comfort of passengers. A bogie of railway vehicle Is composed of many suspension components, such as springs, dampers and etc.. that have an influence on the dynamic behavior of the train wish the wheel/rail profiles and track geometries. Therefore, it Is necessary for engineers to check the Interference between vehicle limit and construction limit with considering the vehicle's behavior, because when the vehicle is running on curved track, it should be have enough clearance from infrastructure for safely, spacially In a subway system. This paper explains the effective method of analysis for vehicle limit considering the vehicle dynamic behavior and reviews the problem of vehicle limit for the Korean Standard Urban Train. The results show that the vehicle limit is over the construction limit when the Korean Standard Urban Train runs on the curved track with 180 m radius of curve.

• Transactions of Materials Processing
• /
• v.15 no.6 s.87
• /
• pp.467-472
• /
• 2006

The forming limit diagram of tube is required for the part design and the formability analysis of tube hydroforming. The finite element analyses of simple bulge test were done to obtain the various strain combinations on FLC. The finite element analysis results were shown that the bursting at various strain combinations could be induced by simple bulge test. The experiment oi tube bulge test was carried out according to the test condition that obtained from finite element analysis and the left hand side of forming limit diagram was built.

• 전자공학회논문지 IE
• /
• v.46 no.3
• /
• pp.33-41
• /
• 2009

Because the stability of obstacle avoidance ability is important for the safe operation of mobile robots, this paper deals with the analysis of dynamic stability of Limit-cycle navigation method that was proposed by authors. Limit-cycle navigation method is fast and easy to implement for fast moving mobile robots using limit-cycle characteristics of the 2nd-order nonlinear function. It can be applied to robots in dynamically changing environment such as the robot soccer. By adjusting the radius of the motion circle and the direction of the obstacle avoidance, the mobile robot can avoid the collision with obstacles and move to the destination point. The stability of Limit-cycle navigation method is analyzed with a linear model. To demonstrate the effectiveness and applicability, it is applied to the robot soccer Simulations and real experiments ascertain the merits of the proposed method.

• Structural Engineering and Mechanics
• /
• v.42 no.2
• /
• pp.247-267
• /
• 2012

Calculating the displacements of retaining walls under seismic loads is a crucial part in optimum design of these structures and unfortunately the techniques based on active seismic pressure are not sufficient alone for an appropriate design of the wall. Using limit analysis concepts, the seismic displacements of retaining walls are studied in present research. In this regard, applying limit analysis method and upper bound theorem, a new procedure is proposed for calculating the yield acceleration, critical angle of failure wedge, and permanent displacements of retaining walls in seismic conditions for two failure mechanisms, namely sliding and sliding-rotational modes. Also, the effect of internal friction angle of soil, the friction angle between wall and soil, maximum acceleration of the earthquake and height of the wall all in the magnitude of seismic displacements has been investigated by the suggested method. Two sets of ground acceleration records related to near-field and far-field domains are employed in analyses and eventually the results obtained from the suggested method are compared with those from other techniques.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.603-608
• /
• 2008

It is well known that the topology optimization for plastic problem is not easy since the iterative analyses to evaluate the objective and cost function with respect to the design variation are very time-consuming. The finite element limit analysis is an efficient tool which is possible to predict collapse modes and sequential collapse loads of a structure considering not only large deformation but also plastic material behavior with moderate computing cost. In this paper, the optimum topology of a structure considering large and plastic deformation is obtained using the finite element limit analysis. To verify the constructed optimization code, topology optimizations of some typical problems are performed and the optimal topologies by elastic design and plastic design are compared.

• Proceedings of the Korean Geotechical Society Conference
• /
• 2008.03a
• /
• pp.1351-1358
• /
• 2008

This paper presents how the load transfer mechanism of the ground anchor affects on the stability analysis of anchored slope. The finite element analysis and the conventional limit equilibrium analysis on the anchored slope were performed and compared. The limit equilibrium analysis of the anchored slope is quite open used in design practice due to the easiness of the analysis. However, the load transfer mechanism is not considered properly for the analysis. When the failure surface passes through the bonded length of an anchor, the anchor load is disregarded and the factor of safety for the anchored slope is smaller than it should be. In this study, the load transfer distribution was incorporated into the limit equilibrium stability analysis of the anchored slope and the results were compared with the results of finite element analysis.

• Structural Engineering and Mechanics
• /
• v.89 no.3
• /
• pp.253-263
• /
• 2024

Slope stability is generally paid more attention to in slope protection works, especially for slope containing weak layers. Two indexes of safety factor and failure model are selected to perform slope stability. Moreover, the finite element limit analysis method comprehensively combines the advantage of the limit analysis method and the finite element method obtaining the upper and lower bounds of the safety factor and the failure mode under the slope stability limit state. In this study, taking a waste dump containing a weak layer as an engineering background, the finite element limit analysis method is adopted to explore the potential failure mode. Meanwhile, the sensitivity analysis of slope stability is performed on geometrical and geotechnical parameters of the waste dump. The results show that the failure mode of the waste dump slope is two wedges if the weak layer is located on the ground surface (Model A), while the slope can be observed as three wedges failure if the weak layer is below the ground surface (Model B). In addition, both failure modes are highly sensitive to the friction angle of the weak layer and the shear strength of waste disposal, and moderately sensitive to the heap height, the dip angle and cohesion of the weak layer, while the toe cutting has limited effect on the slope stability. Moreover, the sensitivity to the excavation of the ground depends on the location of the weak layer and failure mode.