• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.836-839
• /
• 2005

A limit switch box is used for a indicator of a valve actuator. This device indicates an opening and closing of a valve or throttle in a valve actuator. In a ship, equipments are required safety and robustness because of a rough environment and a specific condition during a voyage. However, the limit switch box is used in an indoor environment generally. In order to evaluate the endurance of the limit switch box used in an indoor environment, the endurance tests against salt water have been conducted. Experiment results showed that the limit switch box was corroded severely. Thus, this study developed a new limit switch box which can be used at an outdoor environment. The housing of the developed limit switch box was made by an stainless steel to prevent corrosion.

• 자동차안전학회지
• /
• 제7권4호
• /
• pp.26-30
• /
• 2015

Exceeding the speed limit during vehicle driving is a key factor in the severity of lots of road accidents, and SLIF(Speed Limit Information Function) application is in the initial phase in Korea. SLIF helps the drivers to observe a speed limit when they are driving by providing alert and informing the current limit speed information based on external data using camera and/or digital map, for that reason, environmental conditions could be causes of SLIF malfunctions. In this study, design adequacy analysis of SLIF in respect of false recognition as the Korea traffic environment has been performed. As tentative results, road conditions and structure of speed limit sign as well as system performance often caused misrecognition.

• 한국전산구조공학회논문집
• /
• 제26권3호
• /
• pp.183-189
• /
• 2013

본 논문에서는 불확실성을 확률변수로 가정하고 구조물의 파손기준을 한계상태식(Limit State Equation)으로 정의하였다. 한계상태식을 Fleishman의 3차 다항식으로 근사하고 이론적인 확률 모멘트(Moments)를 계산하였다. Fleishman은 표준정규 분포 확률변수에 대해서만 3차 다항식을 제시하였으나, 본 논문에서는 이를 확장하여 베타, 감마, 균일 분포 등 다양한 확률 변수에 적용하였다. 확률 모멘트를 계산하기 위해서 누률(Cumulants)과 정규화된 한계상태식을 활용하였으며, 피어슨 시스템(Pearson System)을 통해 한계상태식의 확률분포를 근사하였다.

• Structural Engineering and Mechanics
• /
• 제50권2호
• /
• pp.201-214
• /
• 2014

Due to the confinement effects, Steel-Straps Tensioning Technique (SSTT) can significantly enhance the strength and ductility of high-strength concrete (HSC) members (Moghaddam et al. 2008). However, the enhancement especially in strength may result in slender member and more susceptible to instability (Jiang and Teng 2012a). This instability is particularly significant in HSC member as it inherent the brittle nature of the material (Galano et al. 2008). The current slenderness limit expression used in the design is mainly derived from the experiment and analysis results based on Normal strength concrete (NSC) column and therefore the direct application of these slenderness limit expressions to the HSC column is being questioned. Besides, a particular slenderness limit for the SSTT-confined HSC column which incorporated the pre-tensioned force and multilayers effects is not yet available. Hence, an analytical study was carried out in the view of developing a simple equation in order to determine the slenderness limit for HSC column confined with SSTT. Based on the analytical results, it was concluded that the existing slenderness limit expressions used in the design are appropriate for neither HSC columns nor SSTT-confined HSC columns. In this paper, a slenderness limit expression which has incorporated the SSTT-confinement effects is proposed. The proposed expression can also be applied to unconfined HSC columns.

• International Journal of CAD/CAM
• /
• 제6권1호
• /
• pp.139-148
• /
• 2006

Catmull-Clark subdivision scheme provides a powerful method for building smooth and complex surfaces. But the number of faces in the uniformly refined meshes increases exponentially with respect to subdivision depth. Adaptive tessellation reduces the number of faces needed to yield a smooth approximation to the limit surface and, consequently, makes the rendering process more efficient. In this paper, we present a new adaptive tessellation method for general Catmull-Clark subdivision surfaces. Different from previous control mesh refinement based approaches, which generate approximate meshes that usually do not interpolate the limit surface, the new method is based on direct evaluation of the limit surface to generate an inscribed polyhedron of the limit surface. With explicit evaluation of general Catmull-Clark subdivision surfaces becoming available, the new adaptive tessellation method can precisely measure error for every point of the limit surface. Hence, it has complete control of the accuracy of the tessellation result. Cracks are avoided by using a recursive color marking process to ensure that adjacent patches or subpatches use the same limit surface points in the construction of the shared boundary. The new method performs limit surface evaluation only at points that are needed for the final rendering process. Therefore it is very fast and memory efficient. The new method is presented for the general Catmull-Clark subdivision scheme. But it can be used for any subdivision scheme that has an explicit evaluation method for its limit surface.

• 대한기계학회논문집A
• /
• 제31권5호
• /
• pp.586-593
• /
• 2007

This paper proposes closed-form plastic limit load solutions for elbow with local wall thinning at extrados under internal pressure. This work was performed using 3-dimensional, small strain FE analyses based on elastic-perfectly plastic materials. The wide range of elbow and local wall thinning geometries are considered. For systematic analyses for effect of axial thinning extent on limit loads, two limiting cases are considered; a sufficiently long thinning, and the circumferential part-through surface crack. Then, the closed-form plastic limit load solutions for intermediate thinning are obtained by using result of two limiting cases. The effect of axial thinning extent for elbow on plastic limit load is highlighted by comparing with that for straight pipes. Although the proposed limit load solutions are developed for the case when local wall thinning exist in the center of elbow, it is also shown that they can be applied to the case when local wall thinning exists anywhere within elbow.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2014년도 추계학술대회 논문집
• /
• pp.698-698
• /
• 2014

According to the analysis of special medical examination and work environment monitoring data, the rate of C1 and D1 on noise hazard exceeded 90% among those of total hazardous factors. The rate of company exceeding noise exposure limit was also more than 90%. The analysis result shows that main ages diagnosed with C1 and D1 was age of 50s. The majority scale company having workers diagnosed with C1 and D1 was the companies employing 5~49 workers. Types of industries which have a large number of companies exceeding noise exposure limit were automobile and trailer manufacturing, metal processing industry and primary metal manufacturing. A large number of work processes exceeding noise exposure limit were forming and processing work, cutting and bending work and grinding. To reduce the number of company exceeding noise exposure limit, the reduction counterplan should be focused on the type of industry and the work process which exceeded noise exposure limit frequently. However, the reduction counterplan is preemptively necessary to the type of industry and the work process which exceeded noise exposure limit consecutively if the purpose of reduction counterplan is not to merely reduce the number of company exceeding noise exposure limit but to abate workers' suffering from noise.

• 한국자동차공학회논문집
• /
• 제7권5호
• /
• pp.221-229
• /
• 1999

We examined the governing factors of fatigue limit in annealed and austempered ductile iron specimens machined micro hole(dia.<0.4mm) in rotary bending fatigue test. Also, the quantitative relationship between fatigue limit and maximum defect size in specimens was investigated. Artificial defect(micro-pit type, dia.<0.4mm) on specimen surface did not bring about an obvious reduction of fatigue limit in austempered ductile iton(ADI) as compared with annealed ductile iron. According to the investigation of ${\sqrt{area}}_c$ which is the critical defect size to crack initiation at artificial defect, ${\sqrt{area}}_c$ of ADI was larger than that of annealed ductile iron. This shows that the situation of crack initiation at artificial defect in ADI is more difficult in comparison with annealed ductile iron. Maximum defect size is one of the important parameters to predict fatigue limit. And, the quantitative relationship, between the fatigue limit ${\sigma}_{\omega}$ and the maximum defect size ${\sqrt{area}}_{max}$ can be expressed to ${\sigma}_{\omega}^n{\cdot}{\sqrt{area}}_{max}=C_2$ where, $C_2$ are constant. Moreover, it is possible to explain the difference in fatigue limit between, austempered and annealed ductile iron by introducing the parameter ${\delta}(=N_{sg}/N_{total})$in a plain spectimen.

• 한국구조물진단유지관리공학회 논문집
• /
• 제11권1호
• /
• pp.171-180
• /
• 2007

처짐, 응력 및 휨강도 한계상태에 대한 PSSC(prestressed steel and concrete)거더의 신뢰도해석을 수행한다. PSSC 거더는 시공비용과 형하공간의 확보 면에서 지간 40m이상인 교량에 적용하는데 커다란 장점을 가지고 있는 형식이다. 이 논문에서는 다양한 지간, 단면 및 설계 응력수준을 가지는 PSSC 거더를 설계하여 중앙점 처짐, 응력 및 단면 휨모멘트 해석을 수행하고, 각각에 대한 한계상태를 가정한 후, Monte-Carlo 시뮬레이션과 Rackwitz-Fiessler 방법을 이용하여 신뢰도지수를 구한다. 결과를 분석하면 PSSC 거더에 대한 처짐한계상태는 응력한계상태보다 적절하게 큰 신뢰도지수 값을 보이며, 휨강도에 대한 신뢰도지수가 매우 큼을 알 수 있다.

• 대한기계학회논문집A
• /
• 제31권4호
• /
• pp.496-505
• /
• 2007

This paper proposes closed-form plastic limit load solutions for elbows under in-plane bending, via three-dimensional (3-D), small strain FE limit analyses using elastic-perfectly plastic materials. A wide range of elbow and thinning geometries are considered. For systematic analyses of the effect of the axial thinning length on limit loads, two limiting cases are considered; a sufficiently long wall thinning, and the circumferential part-through surface crack. Closed-form plastic limit load solutions for wall thinning with intermediate longitudinal extents are then obtained from these two limiting cases. The effect of the axial extent of wall thinning on plastic limit loads for elbows is highlighted by comparing that for straight pipes. Although the proposed solutions are developed for the case when wall thinning exists in the center of elbows, it is also shown that they can be applied to the case when wall thinning exists anywhere within the elbow.