• Journal of the Korean Magnetics Society
• /
• v.25 no.4
• /
• pp.123-128
• /
• 2015

The iron is an element having a high yield strength, mechanical hardness, good electrical conductivity, and also it has been used in various fields because of ease machining. In bridges have been used tendon made of a steel wire for large loads and light weight. Tension measurement of tendon employed in PreStressed Concrete (PSC) bridge is very important for the bridge safety check. NDT (Non-Destructive Testing) is essential for the safety check, however, magnetic NDT is difficult to apply due to the non-linear magnetization curve and hysteresis loop in the magnetic properties. In this work, for basic study of magnetic NDT application, we have constructed a B-H loop measuring system for 7-strand tendon of which diameter is 15.5 mm, and which can apply tensile stress up to 2.0 GPa. We have measured hysteresis loops of two kinds of tendons under different tensile stress. Amplitude permeability and maximum magnetic induction near knee show the most sensitive and high linearity depends on tensile stress. Relative amplitude permeability was decreased from 500 to 200 and maximum magnetic flux density changed 0.6 T.

• Korean Chemical Engineering Research
• /
• v.44 no.3
• /
• pp.284-288
• /
• 2006

$(Ca,Sr)_{2-y}MgSi_2O_7:Eu^{2+}{_y}$ (CMS) phosphor particles were prepared by using a spray pyrolysis process. The luminescent property was optimized by changing the content of Eu and the post-treatment temperature. The luminescence characteristics were also monitored with changing the ratio of Ca to Sr. The pure tetragonal $Ca_2MgSi_2O_7$ or $Sr_2MgSi_2O_7$ particles were obtained when the post-treatment temperature was over $1,000^{\circ}C$. The highest emission intensity of CMS particles were achieved when the concentration (y) of Eu and the treatment temperature were 0.05 and $1,250^{\circ}C$,respectively. The emission wavelength $({\lambda}_{max})$ of ${(Ca_{1-x},Sr_x)}_{1.95}MgSi_2O_7:{Eu^{2+}}_{0.05}$ was gradually shifted from 524 nm to 456 nm with increasing the content of Sr due to the reduction of crystal field strength. The emission intensity and its width of $Sr_2MgSi_2O_7:Eu$ was greatly enhanced by substituting Ca of less than 10 mol％ for Sr without any significant peak shift. The morphology of as-prepared particles was spherical, but changed to irregular-shaped one after the post treatment at the temperature range from 900 at $1,300^{\circ}C$.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.105-114
• /
• 2015

In this study, an advanced epoxy putty which was as a multi-purpose restoration material being used to restore missing parts in the artifact preservation treatment process was developed. For the purpose of addressing the issues including the workability issue resulting from high strength, the drooping issue resulting from long hardening time during work process and the issue of contaminating the surface of artifact resulting from stained material on tools or gloves, a property comparison was conducted with existing materials to examine the properties of restoration materials in the form of epoxy putty currently being frequently used. For the purpose of addressing the issues of existing materials and allowing the developed epoxy putty to have similar properties, two types of hardeners with different properties were selected to conduct property experiments. As for the hardeners, mercaptan type hardener and aliphatic amine type hardeners in the total of two types were selected for the development. The result showed that the two types were both in the form of paste and their hardening time of 5-10 minutes were about 3-10 times shorter than that of existing materials, thereby improving the work convenience. In terms of abrasion rate to increase workability, it was improved by about 3 times to allow effective and convenient use. As for the issue of contaminating the artifact surface during the process, white micro-balloon was added as filler to address the issue to reduce the oil ingredient to develop multi-purpose restoration material with low shrinkage & high workability in coloring, light weight and cutting force.

• Journal of Conservation Science
• /
• v.31 no.2
• /
• pp.87-94
• /
• 2015

Plastic artwork can be appeared crack, change of color and whitening event by various environment conditions. A large scale plastic artwork often exhibits in outside it will be directly degraded by physical and chemical degradation factor such as strong sunlight, high humidity and rainfall. We should know degradation characteristic of plastics to prevent these damages. In this study, we studied degradation characteristic of plastics (5 types of wide use plastics; polypropylene, polystyrene, polyethylene, polyvinyl chloride, polyurethane) depending on various artificial degradation conditions such as high temperature, ultraviolet and these complex conditions (high temperature and ultraviolet). As a result, polypropylene, polystyrene and polyethylene show the most visible change especially polypropylene, polystyrene. Polypropylene didn't show a great change degree of tensile strength and contact angle, on the other hand polystyrene did. Polypropylene and polystyrene weakened by photo degradation, polyvinyl chloride and polyurethane had relatively good light stability. Also the high temperature and complex conditions were most degradation characteristic. High temperature worked for degradation catalyst because its energy can not enough worked for cut off binding energy of plastics while ultraviolet condition effected as directly degradation condition. Though following results, we expect it can be applied to investigation of degradation factor depending on plastic artwork materials and basic result of plastic artworks conservation.

• Journal of the Korea Concrete Institute
• /
• v.13 no.3
• /
• pp.285-293
• /
• 2001

To improve the vulnerable point and the mechanical property of the existing lightweight foamed concrete, this study was intend to manufacture the lightweight foamed concrete with wasted expanded poly-styrene, examinate and analyze the mechanical property of its. The experiment was being processed with mixing the wasted expanded poly-styrene maximum 40 % by stages and which was mainly basis on the practical mixture. The results of the experiment are following. The flow value is most affected by the mixtured rate of the wasted expanded poly-styrene. The more the mixtured ratio, the less the flow value and the more the more the unit quantity of cement and the W/C, the more the flow value. The apparent specific gravity indicated 0.31∼0.54 and which is seemed to be mainly included in the 0.4 degree and 0.5 degree that are regulated in the KS F 4039. The more the mixtured wasted poly-styrene ratio, the less the apparent specific gravity. The absorbing ratio which was depend on the mixture condition indicated 11 ∼46% and the more the mixtured ratio of the wasted expanded poly-styrene, the less the absorbing ratio remarkably. The compressive strength of the lightweight foamed concrete had a tendency to increase as the mixtured ratio of the wasted poly-styrene, the ratio quantity of cement and the apparent specific gravity increasing but as the ratio of bubble decreasing. The W/C affected little.

• Journal of Bio-Environment Control
• /
• v.17 no.4
• /
• pp.312-318
• /
• 2008

In a pear fruit 'Chuhwangbae' was investigated the effect of the calcium-coated double paper bag on the physical properties of the paper bag, micro meteorological phenomena, and calcium contents in quality of fruit. The calcium-coated paper bag, compared with official paper bags, did not give any effect on light transmission ratio and tensile strength. The change of the inside relative humidity of the paper bag was a little compared with conventional paper bags, but there was no difference in temperature. The contents of the accumulated calcium of the pericarp was remarkably greater than conventional paper bags during the period of 65 days to 160 days after the full bloom, but the flesh remarkably increased at 160 days. The calcium content per concentration of calcium coating greatly increased in 12% of yellow double paper bags and 9, 12% of newspaper double paper bags in case of the pericarp, and in 3% of yellow double paper bags and 6, 9, 12% of newspaper double paper bags in case of the pericarp. As a result of treatment of a radioactive isotope, the amount of accumulated calcium in the pericarp continued until 60 hours after treatment, but there was no difference in the calcium amount between the flesh and no-treatment pericarp. As to the hardness of fruits at the time of harvest, there was no difference in the concentration in case of a yellow double bags. But newspaper double paper bags 6, 12% was significantly difference. Soluble solid remarkably increased in yellow double paper bags 6, 9% and yellow double paper bags 3, 6, 9%. Also, it did not effect on changes of the pericarp, fruit weight and the color of the pericarp.

• Textile Coloration and Finishing
• /
• v.32 no.1
• /
• pp.9-18
• /
• 2020

In this study, we conducted alkali hydrolysis on sea-island type PET ultramicrofiber tricot fabric and dyeing according to the various conditions with black disperse dye. Herein, we evaluated the weight loss rate and tensile strength according to the NaOH contents. The optimal alkali hydrolysis treatment conditions were set to 25 %omf NaOH with a treatment time of 60 min at 110 ℃, and average weight loss rate of the PET ultramicrofiber tricot fabric is about 23 %. The dyeing conditions were investigated with different dyeing temperatures(95-135 ℃), dyeing time(20-60 min), dye contents(2-10 %omf), dispersant contents(1-9 g/ℓ), pH buffer solution contents(1-9 g/ℓ), UV-absorbent contents(5-25 %omf) and reduction cleaning process conditions for black color. We obtained the optimum conditions of the dyeing with the dye contents of 8 %omf, the dispersant contents of 1 g/ℓ, the pH buffer solution contents of 1 g/ℓ, the UV-absorbent contents of 10 %omf, the dyeing temperature of 135 ℃ and the dyeing time of 40 min. The light colorfastness of dyed ultramicrofiber PET tricot fabric was good to excellent in the range of 4 to 5.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.6
• /
• pp.1-8
• /
• 2018

FRP is a new material that is light, has high strength and high durability, and is emerging as a third construction material inside and outside of countries. However, very few studies have been done on curved FRP construction materials that can be used for tunnels or arched bridges. Because a small composite panel specimen is smaller than a full-size specimen, it can be used in a variety of experiments under different conditions. Therefore, in this study, experiments were performed on a void section, a solid section, a connected solid section, and a sand-coating solid section. The results of the experiment show that the connection of composite curved panels with longitudinal connections provides almost equivalent performance to that of a single panel. However, it is necessary to strengthen the connections, since the connections that are most susceptible to damage will break first.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.2
• /
• pp.1204-1210
• /
• 2014

New control methods are proposed for indoor air quality by removing fine airborne dust-particles. As suspended fine dust-particles contain inorganic dust as well as fine organic bacteria, studies for simultaneous control of these contaminants are required. In this study, photocatalytic disinfection of indoor suspended microorganisms such as E. coli and Bacillus subtilis is performed by three types of photocatalysts with UVA irradiation. The UVA irradiation strength was controlled to the minimum $3{\mu}W/cm^2$, and ZnO, $TiO_2$, and ZnO/Laponite ball were used as the catalysts. The results indicate that E. coli was removed over 80 % after about 2 hours of reaction with UVA and all three types of photocatalysts, whereas only with UVA, around 50 % E. coli removal was obtained. Among the catalysts, ZnO/Laponite composite ball was found to have similar sterilizing capacity to $TiO_2$. However, in case of B. subtilis, which has thick cell wall in its spore state, disinfection was not effective under the low UVA irradiation condition, even with the catalysts. Further studies need to figure out the optimal UVA irradiation ranges as well as photocatalysts doses to control airborne dust, to provide healthy clean air environment.

• Horticultural Science & Technology
• /
• v.28 no.3
• /
• pp.381-386
• /
• 2010

The berry growth and pericarp characteristics were characterized to confirm the effects of bagging periods on berry cracking during berry development in 'Kyoho' grape. The berry weight was the highest at 13.4 g in late period of bagging treated at 7 to 9 weeks after full bloom (WAFB) as compared with the lowest of 12.3 g in total period bagging. The berry cracking rate under critical turgor pressure in the non-bagging control was 53.3%, while those of bagging treatments were decreased in the order of 42.7%, 37.3%, 33.3%, and 18.7% in bagged during 3 to 9, 3 to 5, 5 to 7, and 7 to 9 WAFB, respectively. In the results of observation on histological characteristics of pericarp, berry lenticels of whole bagging treatments had smaller and normal shape compared with non-bagging control treatment. Especially on the pericarp of late period bagged during 7 to 9 WAFB, suberization around stomata and micro-cracking were not observed and structural strength of pericarp was increased with thicker sub-epidermal layer and cell wall. Therefore, the results indicate that bagging treatment for two weeks just before the veraison when the day length and daylight is relatively longer and stronger can effectively reduce berry cracking by strengthening structure of pericarp in 'Kyoho' grape.