• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.212-222
• /
• 1992

To use polycrystalline Si Thin Film Transistor (poly-Si TFT) in high density SRAM instead of High Load Resistor (HLR), TFT is needed to show good electrical characteristics such as large carrier mobility, low leakage current, high driver current and low subthreshold swing. To satisfy these electrical characteristics, the trap state density must be reduced in the channel poly. Technological issues pertinent to the channel poly fabrication process are investigated and discussed. They are solid phase growth (SPG), Si-ion implantation, laser annealing and hydrogenation. The electrical properties of several CVD oxides used as the gate oxide of TFT are compared. The dependence of the electrical characteristics of TFT on source-drain ion-implantation dose, drain offset length and dopant lateral diffusion are also described.

• Journal of the Korean Society of Safety
• /
• v.25 no.6
• /
• pp.9-13
• /
• 2010

An experimental study for characteristics of soot were conducted at the post-flame region in jet diffusion flames, where carbon dioxide was used as additives in oxidizer stream. Light-extinction method was performed using He-Ne laser with wave length at 632.8nm for the measurement of relative soot density and soot volume fraction with dimensionless extinction coefficient, $K_e$ and mass specific extinction coefficient, ${\sigma}_s$. To increase of resolution, laser light was modified for sheet-form using concave, convex lenses and slit. C/H ratio was introduced for quantitative analysis of soot growth which is expressed by carbonization and dehydrogen. Also transmission electron microscopy(TEM) was used for observation of morphological shape. The results show that the relative soot density in the post-flame region was lower when carbon dioxide was added in oxidizer stream because of reduction of flame temperature.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.21 no.1
• /
• pp.170-181
• /
• 1997

The purpose of this study was to determine the effect of knit structure and knit density (machine tightness factor) on the dimensional properties and K1-4 values of weft-knitted fabrics followed over eleven cycles of mechanical relaxation to provide the basic data for constructing weft-knitted fabrics for outwear with excellent dimensional stability The eighteenth weft-knitted fabrics were produced with different knit structure (1$\times$1 rib, half-cardigan rib, half-milano rib, interlock, single pique, crossmiss interlock) and machine tightness factor (loose, medium, tight) for this study. Dimensional properties such as width, lengh, area shrinkage and dimensional parameter (K) of eighteenth knitted fabrics including thickness and bulk property were measured. The results were as follows; 1. The dimensional behavior of the Ix1 rib and interlock in relaxation cycles was anisotropic, i.e., length shrinkage was usually associated with a width expansion, whereas the other weft-kntted fabrics which have tuck or miss loops in the knit structure behaved isotropically, i.e., length and width shrinkages were usually found. It was proposed that the difference in dimensional behavior between these structures was due to the dissimilar nonrelaxed geometrical shapes of the individual structural units forming these weft-knitted structures. The mechanical relaxation shrinkage of weft-knitted cotton fabrics was dependent on the tightness of construction. For a range of fabrics knitted on this study, an increase in fabric tightness caused a decrease in the length shrinkage of the fabric accompanied by an increase in its width shrinkage.

• Korean Journal of Clinical Laboratory Science
• /
• v.40 no.2
• /
• pp.118-128
• /
• 2008

The aim of this study was to investigate the effect of electrical stimulation on healing of impaired wound and alteration of mast cells in experimental diabetic rats. Thirty male Sprague-Dawley rats were divided into three groups : incision (control), diabetes+incision (diabetes) and diabetes + incision + electrical stimulation (D/ES). Diabetes was induced in rats by streptozotocin (STZ) injection (60 mg/kg, one time) and 20 mm length incision wounds were created on the back after shaving hair. The electrical stimulation rats were treated with a current intensity of 30~50 V at 120 pps and $140{\mu}s$ for 10 days from 3 days after STZ injection. The lesion and adjacent skin tissues were fixed with 10% buffered formalin, embedded with paraffin. For wound healing analysis, hematoxylin-eosin (HE) and picrosirius red staining were performed. Mast cells (MC) were stained with toluidine blue (pH 0.5) and quantified at ${\times}200$ using a light microscope. The density of keratinocyte proliferation and microvessels in skin tissues were analyzed using a computerized image analysis system on sections immunostained with proliferative cell nuclear antigen (PCNA) and ${\alpha}$-smooth muscle actin (${\alpha}$-SMA), respectively. The results showed that the wound healing rate, collagen density and neoepidermis thickness, density of PCNA-positive cells and density of ${\alpha}$-SMA-positive vessels were significantly higher in D/ES rats than in diabetic rats. The density of MCs and degranulated MCs in D/ES rats were also significantly higher than those in diabetic rats. These findings suggest that the electrical stimulation may promote the tissue repair process by accelerating collagen production, keratinocyte proliferation and angiogenesis in the diabetic rats, and MCs are required for wound healing of skin in rats.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.57 no.3
• /
• pp.302-309
• /
• 2024

This study estimates the target strength of anchovy Engraulis japonicus required for studying their distribution and density using acoustics and evaluates the acoustic scattering characteristics of anchovies by frequency using the Kirchoff ray mode (KRM) model. The experiment was conducted on 30 anchovies with 4.7-21.5 cm total length. The maximum TS_cm (Simming angle, 9.1°; standard deviation, ± 13.1°) according to total length was -66.9, -65.2, -64.4, and -63.4 dB at 38, 70, 120, and 200 kHz, respectively. The average TS_cm (Simming angle: 9.1°, standard deviation: ± 13.1°) according to total length was -68.9, -68.8, -69.6, and -70.0 dB at 38, 70, 120, and 200 kHz, respectively. The results of this study provide an important basis for future studies that use acoustics to estimate the target strength of anchovies.

• Asian Journal of Turfgrass Science
• /
• v.14 no.1
• /
• pp.273-280
• /
• 2000

This study was conducted to evaluate an efficiency of plant growth regulator trinexapacethy(Primo) on the growth response of bentgrass and the change to soil water content in bentgrass green. Based on the results of the study, the following results were observed. 1. During four weeks after treatment, the visual color and turfgrass density of all the treated plots with trinexapac-ethyl(Primo) were more improved rather than without. Two treatments trinexapac-ethyl /$0.02mL\m^2$ and $0.04mL/\m^2$ were more favorable than other treatments. 2. It suggested that optimum rate to reduce the bentgrass growth and to increase the turfgrass density was the trinexapac-ethyl $0.04mL/\m^2$. 3. For six weeks after treatment, all treated plots were not significantly different (P<0.05) in turfgrass root length and root dry weitht. 4. In the treated plots with trinexapac-ethyl $0.04mL/\m^2$ for 25days in bentgrass green, soil water consumption was approximately 35% to 40% compare to the non-treated control.

• The Bulletin of The Korean Astronomical Society
• /
• v.37 no.1
• /
• pp.39.1-39.1
• /
• 2012

Nuclear rings in barred galaxies are sites of active star formation (SF). We investigate SF and its feedback effects occurring in barred galaxies, for the first time, using high-resolution grid-based hydrodynamic simulations. The gaseous medium is assumed to be infinitesimally thin, isothermal, and unmagnetized. The SF recipes include a density threshold corresponding to the Jeans condition, a SF efficiency of 1%, and momentum feedback via Type II supernova events together with stellar-wind mass loss. To investigate various environments, we vary the gas sound speed as well as the efficiency of momentum injection in the in-plane direction. We find that when the sound speed is small, the surface density of a ring becomes largely independent of the azimuthal angle, resulting in star-forming regions distributed over the whole length of the ring. When the sound speed is large, on the other hand, the ring achieves the largest density at the contact points between the dust lanes and the ring where SF occurs preferentially, leading to a clear age gradient of star clusters in the azimuthal direction. Since rings shrink with time, a radial age gradient of star clusters naturally develop regardless of sound speed, consistent with observations. SF persists over 200 Myr, with an average rate of ${\sim}1.3M_{\odot}/yr$ similar to observed values. Rings gradually become hostile to SF as they lose gas into stars and turbulent motions dominate.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.6 no.4
• /
• pp.331-340
• /
• 1982

Numerical analysis is made on the turbulent heat transfer with suspension of solid particles in circular tube with constant heat flux. The mean motion of suspending particles in mixture is treated as the secondary gas flow with virtual density and viscosity. Our modeling of turbulent transport phenomena of suspension flow is based on this assumption and conventional mixing length theory. This paper gives the evidence that the mixing length models can be extended to close the governing equations for two phase turbulent flow with solid boundary at a first order level. Results on Nusselt numbers obtained by analytical treatments are compared with available experimental data and discussed. They suggest that the most important parameters of two phase turbulent heat transfer phenomena are relative particle diameter to pipe diameter, gas-solid loading ratio, and specific heat of suspending material.

• Proceedings of the KSME Conference
• /
• 2000.04b
• /
• pp.835-840
• /
• 2000

The objective of the present study is to investigate the characteristics of pressure wave propagation of viscous fluid flow in a circular pipe line. The goal of this study is to select the best frequency of each control factor of a circular pipe. We intend to approach a formalized mathematical model by a very exact and reasonable polynomial for fluid transmission lines. and we computed this mathematical model by computer. The results show that the oil viscosity decreased as the length of the circular pipe increases. and The energy of pressure wave propagation decreased as the pipe diameter decreases. The factor is that density of oil was changed resonant frequency. It has been found the viscosity characteristics is changed largely by length of hydraulic pipe and volume of cavity tank.

• Progress in Superconductivity
• /
• v.3 no.2
• /
• pp.193-197
• /
• 2002

There are many problems in wire fabrication of long length Bi-2223 superconductor by using conventional extrusion method. They are mainly due to high surface resistance and inhomogeneous distribution of inner stress. Hydrostatic extrusion process will not only decrease the extrusion pressure but also enhance homogeneous deformation of material by reducing friction force between billet and container Hydrostatic extrusion method is considered to be useful fur fabrication of the homogeneous wire with high density. In this paper, hydrostatic extrusion process is introduced to fabricate Bi-2223 superconducting tape, and also discussed are the interface homogeneity and microstructural aspects of extruded BSCCO/Ag billet.