• 한국결정성장학회지
• /
• 제30권4호
• /
• pp.123-130
• /
• 2020

AGM 연축전지(Absorbent Glass Mat Lead-Acid Battery)의 수명 특성을 결정짓는 양극 활물질(Active Material)의 주요 구성 결정인 4BS(Tetrabasic lead Sulfate)의 입자 크기를 제어하기 위해 4BS Nano Seed(NS)를 적용 중에 있다. 4BS NS 적용 시, 나노 입자 특성상 분산 안정성이 저하되어 제 기능을 다하지 못한다. 이를 개선하기 위해 기존 첨가제인 광명단(Red Lead)에 나노 입자의 4BS seed가 포함된 Incorporated Nano Seed(INS)를 함량별로 첨가하여 양극판 분석과 제품 성능을 평가하였다. INS 함량이 증가할수록 4BS 입자 크기는 작아지면서 균일해지는 특성을 확인할 수 있었으며, 반응 비표면적 증가에 따른 고율 방전 특성도 향상되는 것을 알 수 있었다. 극판 제조 공정에서의 개별 극판에 대한 입도 분포의 편차를 확인하기 위해, AGM 연축전지 200 대 대한 내부 저항 및 전압 검사를 진행하였으며 제품 제조 공정 품질 편차가 감소하는 것을 확인하였다.

• 한국재료학회지
• /
• 제30권8호
• /
• pp.426-434
• /
• 2020

The performance characteristics of a lead acid battery are investigated with the content of Sodium Perborate Tetrahydrate (SPT, NaBO₃·4H₂O) in a positive plate active material. SPT, which reacts with water to form hydrogen peroxide, is applied as an additive in the positive plate active material to increase adhesion between the substrate (positive plate) and the active material; this phenomenon is caused by a chemical reaction on the surface of substrate. A positive plate with the increasing content of SPT is prepared to compare its properties. It is confirmed that the oxide layer increases at the interface between the substrate and the active material with increasing content of SPT; this is proven to be an oxide layer through EDS analysis. Battery performance is confirmed: when SPT content is 2.0 wt%, the charging acceptance and high rate discharge properties are improved. In addition, the lifetime performance according to the Standard of Battery Association of Japan (SBA) S0101 test is improved with increasing content of SPT.

• 한국콘텐츠학회논문지
• /
• 제14권12호
• /
• pp.845-853
• /
• 2014

본 연구는 핵의학과에서 가장 많이 사용되고 있는 $^{99m}Tc$에서 방출되는 140 keV 감마선을 기준으로, 세 가지 실험을 통해 기존에 사용되고 있는 납치마와 공기층 납치마를 이용해 Optically Stimulated Luminescence Dosimeter (OSLD) 선량계에 도달하는 선량을 측정하고, 공기층 납치마의 피폭선량 감소효과에 대해 연구했다. 그 결과 선량계와 납판 사이의 거리를 납치마의 공기층이라고 가정했을 때, 선량계와 0.2 mm 납판 사이의 거리가 없는 0 Cm일 때 측정된 10개의 선량계의 평균값은 0.515 mSv이고, 선량계와 납판 사이의 거리를 20 Cm로 떨어뜨린 경우 10개의 측정값의 평균이 0.138 mSv로 약 0.377 mSv의 선량 감소 효과를 보였다. 선량계와 0.5 mm 납판 사이의 거리가 없는 0 Cm일 때 10개의 선량계의 측정값의 평균은 0.296 mSv이고, 선량계와 납판 사이의 거리를 20 Cm로 떨어뜨린 경우 10개의 측정값의 평균이 0.075 mSv로 약 0.221 mSv의 선량 감소 효과를 보였다. 3일 간의 누적선량을 측정한 결과, 공기층이 없는 납치마의 경우 측정된 누적선량의 평균은 0.238 mSv, 공기층 납치마의 누적선량은 0.176 mSv로 0.062 mSv의 선량 감소 효과를 보였다. 한 달 간의 누적선량을 측정한 결과, 공기층이 없는 납치마의 누적선량의 평균은 0.59 mSv, 공기층 납치마의 누적선량은 0.54 mSv로 0.05 mSv의 선량 감소 효과를 보였다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.128-133
• /
• 2004

This study has been focused on the development of shear forming process of grid for lead-acid battery. The grid plays an important role in the flow of electricity because the grid is a skeleton of the pasted plate. Therefore, it must be of the highest quality to prevent plate failures and then, battery failure, and ensure the best battery performance possible. The finite element analysis of the shear forming process is carried out and the result is compared with the experimental data. The influence of the numerical parameters such as clearance, velocity of punch and critical damage value on the simulation results turns out to be very considerable.

• 한국응용과학기술학회지
• /
• 제26권3호
• /
• pp.335-340
• /
• 2009

This study investigates the paste mixing of positive active materials which, affect the life cycle of batteries in Pb-Ca-Sn grids, and generation of 4BS in a curing process and considers the effects of these things on the initial charge characteristics and life cycle. In the results of the experiments applied in this study, it was possible to reduce the curing time in which the fine 4BS was formed by the mixing of the positive active materials of lead acid battery applied at high temperature compared to that of the existing coarse 4BS and that represented some improvements in the life cycle performance.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2010년도 추계학술대회 초록집
• /
• pp.82.2-82.2
• /
• 2010

The development of bipolar plate having high efficiency and chemical properties has a major impact on fuel cell applications commercialization. Even though graphite bipolar plate has high electric conductivity and chemical resistance, it has demerits about mass production and brittle property for commercialization. Hence, metallic bipolar plate can be substitute for fuel cell bipolar plate. Although its inadequate corrosion behavior under PEMFC environment lead to a deterioration of membrane by dissolved metal ions, metallic bipolar plate for PEMFC is more suitable for automotive and residential power generation system because of its high mechanical strength, low gas permeability and applicability to mass production. Therefore, several types of coating has been applied to prevent corrosion and oxide film growth and to achieve more high durability. This work presents durability of coated metal bipolar plate for low temperature PEMFC which made for fuel cell vehicle. This results showed surface treatment increase long-term durability, even electric conductivity and corrosion resistance.

• Journal of Advanced Marine Engineering and Technology
• /
• 제23권4호
• /
• pp.565-573
• /
• 1999

Hihg Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view points this is very preferable since the reduction in the hull weight. however to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross sect6ion of a ship's hull also decreases. This may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonliner analysis of isolated and stiffened plates is required for structural sys-tem analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluated the inplane rigidity of plates subjected to uniaxial compression.

• Bulletin of the Korean Chemical Society
• /
• 제32권3호
• /
• pp.915-920
• /
• 2011

Four esters of succinic and maleic acid were synthesized, separated by thin-layer chromatography (TLC), and identified using matrix-assisted laser desorption/ionization-mass spectrometry (MALDI-MS). A comparison of matrix materials showed that 2,6-dihydroxybenzoic acid (2,6-DHB) yielded a greater ionization efficiency than 2,5-DHB prior to TLC separation. The location of each ester sample on the TLC plate was estimated by comparing the developed plate with a duplicate plate that had been visualized by immersion in a $KMnO_4$ solution. Generally, mass spectra obtained from the $KMnO_4$-visualized plate were relatively poor. Reproducible mass spectra with high peak abundance were difficult to obtain using the 2,6-DHB matrix from crude synthetic esters extracted from the TLC plates. Significant improvements in both reproducibility and sensitivity were realized by using pencil lead as the MALDI matrix. The current methodology will be beneficial to organic chemists since it can provide a guideline for simple and rapid characterization of small organic compounds.

• 한국표면공학회지
• /
• 제19권3호
• /
• pp.92-108
• /
• 1986

An electroplating on the lead frame fabricated from domestic copper plate was studied experimentally. In this study, nickel was plated on the thin copper lead frame and silver layer was coated on the nickel film in the cyanide electrolyte. The effect of process variables such as current density, plating time, coating thickness and flow rate of electrolytic solution on the properties of coating was investigated. Some samples on each step were fabricated during electroplating. The results obtained from polarization measurement, observation of SEM photograph, adhesion test of coating and microhardness test are as follows. On silver plating, polarization resistance of potentiostatic cathodic polarization curve is reduced as the flow rate of Ag electrolytic solution increases. And above resistance is also reduced when the minor chemicals of sodium cyanide and sodium carbonate are added in potassium silver cyanide bath. The reduced polarization resistance makes silver deposition on the cathode easy. An increase in the current density and the coating thickness causes the particle size of deposit to coarsen, and consequently the Knoop microhardness of the coating decreases. On selective plating an increase in the flow rate of plating solution lead to do high speed plating with high current density. In this case, the surface morphology of deposit is of fine microstructure with high Knoop hardness. An increasing trend of the adhesion of coating was shown with increasing the current density and flow rate of electrolytic solution.

• 한국항해항만학회:학술대회논문집
• /
• 한국항해항만학회 1996년도 The Korean Institute of Navigation 1996년도 한·중 국제학술 심포지움 및 추계학술발표회 논문집
• /
• pp.95-110
• /
• 1996

High Tensile Steel enables to reduce the plate thickness comparing to the case when Mild Steel is used. From the economical view point this is very preferable since the reduction in the hull weight. However to use the High Tensile Steel effectively the plate thickness may become thin so that the occurrence of buckling is inevitable and design allowing plate buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling, buckling may be necessary. If the inplane stiffness of the plating decreases due to buckling the flexural rigidity of the cross section of a ship's hull also decreases. this may lead to excessive deflection of the hull girder under longitudinal bending. In these cases a precise estimation of plate's behavior after buckling is necessary and nonlinear analysis of isolated and stiffened plates is required for structural system analysis. In this connection this paper discusses nonlinear behaviour of thin plate under thrust. Based on the analytical method elastic large deflection analysis of isolated plate is perform and simple expression are derived to evaluate the inplane rigidity of plates subjected to uniaxial compression.