• Structural Engineering and Mechanics
• /
• 제65권3호
• /
• pp.303-314
• /
• 2018

Shear walls are a typical member under a complex stress state and have complicated mechanical properties and failure modes. The separated-elements model Genetic Evolutionary Structural Optimization (GESO), which is a combination of an elastic-plastic stress method and an optimization method, has been introduced in the literature for designing such members. Although the separated-elements model GESO method is well recognized due to its stability, feasibility, and economy, its adequacy has not been experimentally verified. This paper seeks to validate the adequacy of the separated-elements model GESO method against experimental data and demonstrate its feasibility and advantages over the traditional elastic stress method. Two types of reinforced concrete shear wall specimens, which had the location of an opening in the middle bottom and the center region, respectively, were utilized for this study. For each type, two specimens were designed using the separated-elements model GESO method and elastic stress method, respectively. All specimens were subjected to a constant vertical load and an incremental lateral load until failure. Test results indicated that the ultimate bearing capacity, failure modes, and main crack types of the shear walls designed using the two methods were similar, but the ductility indexes including the stiffness degradation, deformability, reinforcement yielding, and crack development of the specimens designed using the separated-elements model GESO method were superior to those using the elastic stress method. Additionally, the shear walls designed using the separated-elements model GESO method, had a reinforcement layout which could closely resist the actual critical stress, and thus a reduced amount of steel bars were required for such shear walls.

• 동력기계공학회지
• /
• 제21권3호
• /
• pp.85-92
• /
• 2017

Global air traffic is forecast to grow at an average annual rate of around 5% in the next 20 years. The continuous growth of air traffic and raised environmental awareness put increasing pressure on aero engine manufacturers to reduce fuel burn and emissions. NEWAC are a new integrated program of the European Union with focus on innovative core engine concepts to achieve this problem. In this paper, Within NEWAC, active core engine configurations will be investigated. the investigation is focused on the optimal design of the CAC heat exchanger for active core. For optimal design of he CAC heat exchanger, the HTFS of basic design of heat exchanger are analyzed so as to proceed an optimization routines based on Response Surface Method(RSM) and Design of Experiment(DOE). As a result, CAC heat exchanger optimized by 1.0314 lb/s mass flow rate and 3.9058 mm TP of tube layout and 206.8181 mm height of heat exchanger and 918 tube number for heat transfer and pressure drop. We confirm the design optimization using RSM and DOE is useful on complex structure of heat exchanger.

• International Journal of CAD/CAM
• /
• 제3권1_2호
• /
• pp.19-29
• /
• 2003

Disassembly is a fundamental process needed for component reuse and material recycling in all assembled products. Integral attachments, also known as 'snap' fits, are favored fastening means in design for assembly (DFA) methodologies, but not necessarily a favored choice for design for disassembly. In this paper, design methods of a new class of integral attachments are proposed, where the snapped joints can be disengaged by the application of localized heat sources. The design problem of reversible integral attachments is posed as the design of compliant mechanisms actuated with localized thermal expansion of materials. Topology optimization technique is utilized to obtain conceptual layout of snap-fit mechanisms that realizes a desired deformation of snapped features for joint release. Two design approaches are attempted and design results of each approach are presented, where the geometrical configuration extracted from optimal topologies are simplified to enhance the manufacturability for the conventional injection molding technologies. To maximize the magnitude of deformation, a design scheme has been proposed to include boundary conditions as design variables. Final designs are verified using commercial software for finite element analysis.

• 한국BIM학회 논문집
• /
• 제10권3호
• /
• pp.22-32
• /
• 2020

Apartment building site planning is one of time consuming and labor-intensive tasks in architectural design field, due to its complexity in zoning regulations, building codes, local restrictions, and site-specific conditions. In other words, the process can be seen as a very complicated mathematical function with layers of variables and parameters, which ironically can be automated using computational methods on parametric tools. In this paper, a practical method of automating site planning of an apartment complex has been proposed by utilizing parametric approaches in Rhino 3D and Grasshopper. Two primary parameters, building heights and positions, determine the efficacy of building layouts under all regulatory standards, thus testing out numerous combinations of the two will produce some successful layout alternatives. For this, equation solver has been used for iterating the parametric model to sort out meaningful results among others. It also has been proven that the proposed process significantly reduced the time in site planning down to less than an hour on most cases, and many successful alternatives could be obtained by using multiple computers. Post evaluation processes such as day light and view shed analysis helped sort out the best performing ones out of functioning alternatives.

• 전자공학회논문지CI
• /
• 제45권1호
• /
• pp.37-47
• /
• 2008

DSP에서 제공되는 주소 생성 유닛은 데이터 패스와 병렬적으로 주소 연산을 수행할 수 있게 해 줌으로써, DSP 코드 생성에 중요한 역할을 한다. 프로그램 변수들의 메모리 레이아웃을 결정하는 문제는 주소 생성 유닛의 기능을 이용하여 주소 연산용 명령어를 줄이는 최적화이다. 메모리 레이아웃 생성 단계와 주소 포인터 할당 단계로 구분 되는 이 최적화에서 본 논문은 주소 연산 코드의 수가 최소가 되도록 DSP용 코드 생성의 효과적인 주소 포인터 할당 문제를 다룬다. 제안하는 알고리즘은 고정된 메모리 레이아웃을 가질 때 주소 포인터 할당을 수행하는 기존의 알고리즘의 시간 복잡도를 줄이는 기법이다. 메모리 크기와 수행 시간을 줄이기 위해 알고리즘을 수행할 때 핵심적인 요소들만을 고려하도록 강한 가지치기 방법을 사용하였다. 또한 주소 포인터 할당 문제는 메모리 레이아웃에 영향을 크게 받는 문제이기 때문에 본 논문은 주어진 메모리 레이아웃을 갱신하여 반복적으로 성능을 개선하는 방법을 제안한다. 약 3,000여개의 실제 프로그램으로부터 얻은 변수 접근 시퀀스를 제공하는 OffsetStone 벤치마크를 이용한 실험결과를 통해 본 논문에서 제안한 기법과 알고리즘을 테스트 했다. 제안한 방법은 전통적인 방법보다 평균 25.9%의 적은 주소 코드를 생성해 냄을 보인다.

• Journal of Computational Design and Engineering
• /
• 제1권2호
• /
• pp.140-151
• /
• 2014

Storing, and the loading and unloading of materials at production sites in the manufacturing sector for mass production is a critical problem that affects various aspects: the layout of the factory, line-side space, logistics, workers' work paths and ease of work, automatic procurement of components, and transfer and supply. Traditionally, the nesting problem has been an issue to improve the efficiency of raw materials; further, research into mainly 2D optimization has progressed. Also, recently, research into the expanded usage of 3D models to implement packing optimization has been actively carried out. Nevertheless, packing algorithms using 3D models are not widely used in practice, due to the large decrease in efficiency, owing to the complexity and excessive computational time. In this paper, the problem of efficiently loading and unloading freeform 3D objects into a given container has been solved, by considering the 3D form, ease of loading and unloading, and packing density. For this reason, a Group Packing Approach for workers has been developed, by using analyzed truck packing work patterns and Group Technology, which is to enhance the efficiency of storage in the manufacturing sector. Also, an algorithm for 3D packing has been developed, and implemented in a commercial 3D CAD modeling system. The 3D packing method consists of a grouping algorithm, a sequencing algorithm, an orientating algorithm, and a loading algorithm. These algorithms concern the respective aspects: the packing order, orientation decisions of parts, collision checking among parts and processing, position decisions of parts, efficiency verification, and loading and unloading simulation. Storage optimization and examination of the ease of loading and unloading are possible, and various kinds of engineering analysis, such as work performance analysis, are facilitated through the intelligent 3D packing method developed in this paper, by using the results of the 3D model.

• 한국수자원학회논문집
• /
• 제38권12호
• /
• pp.1029-1037
• /
• 2005

본 연구는 도시 우수관망 설계 시 주어진 설계유량을 효율적이고 경제적인 단면 구성과 관망에 따른 우수배제 능력을 극대화시키기 위해 최적화 기법인 동적계획법(Dynamic Programming : DP)의 특수한 방법인 이산미분형 동적계획법(Discrete Differential Dynamic programming DDDP)를 이용해 최적화된 설계조건을 구할 수 있도록 하였다. 이산미분형 동적계획법의 기법은 설계유량과 맨홀의 위치가 결정되면 그에 따른 최적 우수시스템이 될 수 있는 관의 용량, 경사, 수위, 수심, 위험도, 회수비용 등을 결정할 수 있는 방법으로 이는 공사비용에 따를 최소비용을 목적함수로 위험도 분석을 통하여 최적화된 조건을 찾는 방법으로 모형개발을 하였다. 개발된 모형을 실제 단지계획의 합리식으로 설계된 우수관망 계획과 비교 검증하여 보다 경제적이고 효율적인 우수관망 시스템을 구축하는 모형을 제시하였다.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -1
• /
• pp.361-364
• /
• 2002

Shortest path problem belongs to the combinatorial optimization problem and plays an important role in the field of computer aided design. It can either be directly applied as in the case of routing or serves as a important subroutine in more complex problems. In this paper, a systolic array for the SSSP(single-source shortest path problem) was derived. The array was modeled and simulated in RTL level using VHDL, then synthesized to a schematic and finally implemented to a layout using the cell library based on 0.35 $\mu\textrm{m}$ CMOS 1-poly 4-metal CMOS technology.

• Transactions on Electrical and Electronic Materials
• /
• 제18권2호
• /
• pp.59-61
• /
• 2017

This research was analyzed thermal characteristics that was appointed disadvantage when smart LED driver ICs was packaged and we applied extracted thermal characteristics for optimal layout design. We confirmed reliability of smart LED driver ICs package without additional heat sink. If the package is not heat sink, we are possible to minimize package. For extracting thermal loss due to overshoot current, we increased driver current by two and three times. As a result of experiment, we obtained 22 mW and 49.5 mW thermal loss. And we obtained optimal data of 350 mA driver current. It is important to distance between power MOSFET and driver ICs. If the distance was increased, the temperature of package was decreased. And so we obtained optimal data of 3.7 mm distance between power MOSFET and driver ICs. Finally, we fabricated real package and we analyzed the electrical characteristics. We obtained constant 35 V output voltage and 80% efficiency.

• 한국초전도ㆍ저온공학회논문지
• /
• 제18권3호
• /
• pp.10-20
• /
• 2016

The Cable-In-Conduit-Conductor (CICC) for the ITER tokamak Central Solenoid (CS) has undergone design change since the first prototype conductor sample was tested in 2010. After tests showed that the performance of initial conductor samples degraded rapidly without stabilization, an alternate design with shorter sub-cable twist pitches was tested and discovered to satisfy performance requirements, namely that the minimum current sharing temperature ($T_{cs}$) remained above a given limit under DC bias. With consistent successful performance of ITER CS conductor CICC samples using the alternate design, an attempt is made here to revisit the internal electromagnetic properties of the CICC cable design to identify any correlation with conductor performance. Results of this study suggest that there may be a simple link between the $Nb_3Sn$ CICC internal self-field and its $T_{cs}$ performance. The study also suggests that an optimization process should exist that can further improve the performance of $Nb_3Sn$ based CICC.