• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.13 no.9
• /
• pp.796-800
• /
• 2000

Bi$_2$Sr$_2$Ca$_{n}$Cu$_{n+1}$ O$_{y}$(n$\geq$0; BSCCO) thin film is fabricated via two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-low growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.on.n.

• Progress in Superconductivity
• /
• v.1 no.1
• /
• pp.51-55
• /
• 1999

A Ni/Ag/Stainless steel 310S(SS310S) multi-layer sheet has been fabricated by a combination of vacuum brazing, cold rolling and texture annealing processes. After heat-treating the thin Ni/Ag/SS310S multi-layer sheet at $900^{\circ}C$ for 2h, development of (100)<001>cube texture on Ni surface was revealed by (111) pole figure. Quantitative chemical analysis was made by EPMA for the cross-section of the Ni/Ag/SS310S multi-layer sheet. EPMA results showed that Ag diffusion into the Ni layer, which may suppress the cube texture development, was negligible. A small amount of Cr atoms were detected in the Ni layer. It showed that Ag can be used as a chemical barrier of alloying element atoms in Ni layer for the Ni/Ag/SS310S multi-layer sheet and a strong cube texture was developed for the Ni layer in the Ni/Ag/SS310S multi-layer sheet.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.1625-1630
• /
• 2004

An experimental study was carried out to investigate influence of flow conditions on a boundary layer to the near-wake of a flat plate. The flow condition in the vicinity of trailing edge that is influenced by upstream condition history is an essential factor that determines the physical characteristics of a near-wake. Various tripping wires were used to change boundary layer flow condition of upstream at the freestream velocity of 6.0 m/sec. Measurements of the boundary layer and near-wake according to the change of upstream conditions were conducted by using both I-probe(55P14 for boundary layer) and X-probe(55P61 for wake). Normalized velocity profiles of the boundary layer were shown the flow types such as laminar boundary layer, transition, and turbulent boundary layer at 0.95C from the leading edge. The velocity and turbulence intensity profiles of the near-wake for the case of laminar boundary layer at the flat plate surface exhibited a defect and a double peak showing perfect symmetry, respectively.

• Journal of Environmental Science International
• /
• v.7 no.2
• /
• pp.195-202
• /
• 1998

The low level atmospheric obsewation carried out to Investigate magnitude, formation and dissipation of nocturnal surface Inversion layer, also to survey relation to each meterological parameter In Inversion layer at Pusan power plant for Oct. 13, 1996. As coastal area, the surface Inversion layer height was relatively high(186m), and after sunset unstable layer formated firom surface to around 40m, and the Inversion layer was left still in the upper layer. The surface Inversion layer dissipated at 0920LST perfectly. The layer that strong Inversion layer was formated, showed steep variation of potential temperature and wand speed and relative humidity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.230-234
• /
• 2000

Bi$_2$Sr$_2$Ca$_{n}$Cu$_{n+1}$ O$_{y}$(n$\geq$0; BSCCO)thin film is fabricated via two different processes using an ion beam sputtering method i.e. co-deposition and layer-by-layer deposition. A single phase of Bi2212 can be fabricated via the co-deposition process. While it cannot be obtained by the layer-by-layer process. Ultra-law growth rate in our ion beam sputtering system brings out the difference in Bi element adsorption between the two processes and results in only 30% adsorption against total incident Bi amount by layer-by-layer deposition, in contrast to enough Bi adsorption by co-deposition.on.n.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.07a
• /
• pp.67-70
• /
• 2000

In this paper, all SCR recombination currents including setback and graded layer's recombination currents are analytically introduced for the first time. Different emitter-base structures are tested to prove the validity of the model. In 1995, the analytical equations of electric field, electrostatic potential, and junction capacitance for abrupt and linearly graded heterojunctions with or without a setback layer was derived. But setback layer and linearly graded layer's recombination current was considered numerically. In this paper, recombination current model included setback layer and graded layer is proposed. New recombination current model also includes abrupt heterojunction's recombination current model. In this paper, new recombination current model analytically explains effects of setback layer and graded layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.432-435
• /
• 1997

In AC PDP, electrodes are covered with dielectric layer and the discharge is formed on the surface of the dielectric layer. MgO protection layer on the dielectric layer in PDP prevents a dielectric layer from sputtering and lowers the firing voltage due to a large secondary electron emission yield( ${\gamma}$ ). Until now, the MgO protection layer is mainly prepared by E-beam evaporation. However, there are some problems that is easy pollution and change of its characteristics with time and delamination. Therefore, in this study, MgO protection layer is prepared on dielectric layer by reactive R.F. magnetron sputtering with MgO target. Discharge characteristics and secondary electron emission coefficients of PDP are studied as a parameter of preparation conditions. Discharge voltage characteristics of the prepared MgO layer can be stable and improved by the annealing process in vacuum chamber.

• Journal of Magnetics
• /
• v.10 no.3
• /
• pp.99-102
• /
• 2005

Modification in exchange bias of a NiFe/FeMn/NiFe trilayer, on introduction of a nonmagnetic Al layer at the top FeMn/NiFe interface, is investigated in multilayers prepared by rf magnetron sputtering. The introduction of Al layer leads to vanishing of bias of the top NiFe layer. But the bias for the bottom NiFe layer increases steadily with increasing Al layer thickness and attains bias (230 Oe) which is greater than that of the trilayer without the Al layer (150 Oe). When the top NiFe layer thickness is varied, exchange bias has highest value at 12 nm thickness for 1 nm thicknes of Al layer. Ion beam etching of the top NiFe layer also leads to an enhancement in bias for the bottom NiFe layer.

• Journal of Electrochemical Science and Technology
• /
• v.12 no.2
• /
• pp.225-229
• /
• 2021

Commercially available continuous glucose sensors require the operation stability for more than two weeks. Typically, the sensor comprises a sensing layer and an over-coating layer for the stable operation inside the body. In the sensing layer, enzymes and mediators are cross-linked together for the effective sensing of the glucose. The over-coating layer limits the flux of glucose and works as a biocompatible layer to the body fluids. Here, we report the simple preparation of the flux-limiting layer by the condensation of polyethyleneimine (PEI), tri-epoxide linker, and trimethylolpropane triglycidyl ether (PTGE). The sensor is constructed by a layer-by-layer drop-coating of the sensing layer containing glucose dehydrogenase and the PEI-derived blocking layer. It is stable for more than 14 days, which is enough for the sensor in the continuous monitor glucose monitoring (CGM) system.

• Annual Conference on Human and Language Technology
• /
• 2021.10a
• /
• pp.410-413
• /
• 2021

본 논문에서는 분류 모델의 주류로 사용되고 있는 Encoder 기반 사전학습 모델(BERT, ALBERT, ELECTRA)의 내부 Encoder Layer가 하부 Layer에서는 Syntactic한 분석을 진행하고 상부 Layer로 갈수록 Semantic 한 분석을 진행하는 점, Layer가 구성됨에 따라 Semantic 정보가 Syntactic 정보를 개선해 나간다 점에 기반한 기존 연구 결과를 바탕으로 Encoder Layer를 구성함에 따라 어떻게 성능이 변화하는지 측정한다. 그리고 의도 분류를 위한 학습 데이터 셋도 분류하고자 하는 성격에 따라 Syntactic한 구성과 Semantic한 구성을 보인다는 점에 착안하여 ALBERT 및 ELECTRA를 이용한 의도 분류 모델을 구축하고 각 데이터 셋에 맞는 최적의 Encoder Layer 구성을 가지는 모델을 비교한 결과, 두 데이터 셋 간에 다른 Layer 구성을 보이는 점과 기존 모델보다 성능이 향상됨을 확인하였다.