• Journal of Biosystems Engineering
• /
• 제43권4호
• /
• pp.285-295
• /
• 2018

Purpose: The aim of this study is to develop a three-wheel riding cultivator for improving the performance of the current four-wheel riding cultivators in the market. Methods: A prototype three-wheel riding cultivator with the rated power of 15.5-kW, a primary hydrostatic and a two-speed selective gear transmission shifts, front/rear three-wheel drive, a hydraulic wheel tread adjustment, and the mid-section attachment of the major implements was designed and constructed. Its specifications and basic performance are investigated. Results: The maximum speeds of the prototype at the low and high stages were measured to be approximately 7.31, and 11.29 km/h in forward travel, respectively, and approximately 3.60, and 6.37 km/h in rearward travel, respectively. The minimum ground clearance is shown to be 670 mm. The rotating speeds of the power takeoff (PTO) shaft at the low and high stages are shown to be approximately 795 and 1,140 rpm, respectively. The tread of the rear wheels, the minimum radius of turning, and the maximum lifting height of the parallel link device are measured to be within 1,320-1,720 mm, 2.80 m, and 390 mm, respectively. Approximately 25.3% and 74.7% of the total weight of the prototype are distributed in the front and rear wheels on flat ground, respectively. When the tread of rear wheels increased from 1,320 to 1,720 mm, the left and right static lateral overturning angles increased from $33.4^{\circ}$ to $39.1^{\circ}$ and from $29.0^{\circ}$ to $36.1^{\circ}$, respectively. Conclusions: The prototype three-wheel riding cultivator showed a wide range of travel and PTO speeds, high minimum ground clearance, small minimum radius of turning, and easy control of the rear wheel tread. Further, the easy observation of cultivating operations by mid-mounting the implements can improve quality of work. Therefore, the prototype is expected to contribute to the riding mechanization of cultivating operations for various upland crops in Korea.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• 제35권1호
• /
• pp.15-22
• /
• 2022

This paper introduces research on the hinge joint of modular structure joints using finite element analysis. The modular structure has a characteristic in that it is difficult to expect the integrity of columns and beams between unit modules because the construction is carried out such that the modules are stacked. However, the current modular design ignores these structural characteristics, considers the moment transmission for the lateral force, and analyzes it in the same manner as the existing steel structure. Moreover, to fasten the moment bonding, bolts are fastened outside and inside the module, resulting in an unreasonable situation in which the finish is added after assembly. To consider the characteristics that are difficult to expect, such as unity, a modular structure system using hinge joints was proposed. This paper proposed and reviewed the basic theory of joints by devising a modified scissors model that is modified from the scissors model used in other research to verify the transmission of load when changing from the existing moment junction to a hinge junction. Based on the basics, the results were verified by comparing them with Midas Gen, a structural analysis program. Additionally, the member strength and usability were reviewed by changing the modular structure designed as a moment joint to a hinge joint.

• Journal of International Area Studies (JIAS)
• /
• 제13권1호
• /
• pp.107-133
• /
• 2009

International relations in the 21st century is featured by boundless competition among nations to secure sufficient energy resources for achieving economic development. Resource diplomacy, therefore, is competitive in its nature, which is derived from the fact that resources of the globe are limited. Chinese recent economic growth has been possible mainly due to its success in resource diplomacy. The Chinese resource diplomacy has shown two different patterns according to target regions. On the one hand, China has pursued multilateral approach to Central Asia region, by which China aimed to secure energy with joint exploration method in the region. Chinese resource diplomacy toward Africa, on the other hand, has been based on bilateral approach combined with unit-centered economic aid to African nations. This difference in Chinese foreign policy pattern seems to be derived from three factors: namely, Chinese strategic considerations on geopolitical condition, regional security sensitivity, and legacies of Chinese long-time non-alignment diplomacy since the 1950s. Whether China is able to maintain the current pattern of resource diplomacy will be depended on how wisely China pursue its relations with two other global powers: Russia in the Central Asia and the U.S. in Africa. In this regard, the Chinese resource diplomacy is expected to work as determining factor of shaping a pattern of tri-lateral strategic relations among the U.S., Russia, and China. Chinese resource diplomacy thus will determine the future direction of the global politics in terms of strategic arrangement.

• Journal of Internet of Things and Convergence
• /
• 제9권3호
• /
• pp.93-98
• /
• 2023

In this paper, an artificial neural network based on simulated annealing was constructed. The mapping relationship between the parameters of micro-scaled flow channels electrochemical machining and the channel shape was established by training the samples. The depth and width of micro-scaled flow channels electrochemical machining on stainless steel surface were predicted, and the flow channels experiment was carried out with pulse power supply in NaNO3 solution to verify the established network model. The results show that the depth and width of the channel predicted by the simulated annealing artificial neural network with "4-7-2" structure are very close to the experimental values, and the error is less than 5.3%. The predicted and experimental data show that the etching degree in the process of channels electrochemical machining is closely related to voltage and current density. When the voltage is less than 5V, a "small island" is formed in the channel; When the voltage is greater than 40V, the lateral etching of the channel is relatively large, and the "dam" between the channels disappears. When the voltage is 25V, the machining morphology of the channel is the best.

• 한국체육학회지인문사회과학편
• /
• 제55권2호
• /
• pp.643-655
• /
• 2016

The purpose of this study was to investigate biomechanical differences between young and old adults during downhill walking on a treadmill in order to understand the mechanisms of elderly falls. Eighteen healthy young females(YG: yrs: 21.17±1.5) and eighteen healthy old females(OG: yrs: 66.67±1.33) participated in this study. They were asked to walk at their preferred speed on a treadmill at level, 7.5° and 15° decline. OG walked more wobbly in the medial and lateral directions than YG(p<.05). As slope got steeper, OG had smaller ROM(range of motion) of ankle and knee joints compared with YG. However, there was no difference in ROM of the hip between OG and YG, but maximum extension angle of OG was smaller compared with YG(p<.05). Smaller extensor moment was generated on OG during downhill walking(p<.05). It was hypothesized that more risk factors would be found on older people compared to young people during downhill. However, older people actually walks with a safer strategy compared to young people during downhill. Finally, current findings about biomechanical characteristics of elderly walking would provide useful fundamental information for a follow-up study regarding the prevention of elderly fall during their daily life.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• 제30권6A호
• /
• pp.525-534
• /
• 2010

A road curbstone is a structure installed at the boundary of the sidewalk and the street with the objectives of road drainage, drawing attention and such. The current general construction method of curbstones places foundation concrete for the curbstones first, waits until the concrete reaches the strength to support the curbstones, places the curbstones on top, and then places the gutter and rear filling concrete. Such method has the issues of poor compaction and weakened bond strength of concrete due to split placing of concrete, and causes the curbstones to easily separate due to vehicle impact or earth pressure, in turn creating maintenance costs and spoiling the aesthetics. To improve such conventional construction methods, an all-in-one method was developed using formwork rail and jig where both the curbstones and gutter can be worked at the same time, and to evaluate the structural performance, static tests of lateral loading test, pullout test, and bending test were executed, and dynamic tests such as pendulum test and actual vehicle impact test were executed. In all tests, the all-in-one construction method using formwork rail and jig was shown to be superior to the conventional construction method by the increase of construction quality and bond strength of concrete.

• Journal of the Korea institute for structural maintenance and inspection
• /
• 제13권4호통권56호
• /
• pp.180-187
• /
• 2009

The objective of this research is to verify the code-specified girder distribution factors (GDF) for continuous steel girder bridges by field testing. Previous analytical study revealed that current GDF's specified in AASHTO Standard and AASHTO LRFD, developed for the simple span bridges are conservative even for the continuous bridges. In this study, field tests were performed for three continuous steel girder bridges to validate the GDF's specified in the AASHTO codes. The results show that the code values are conservative when compared with field tests, and in some cases, too conservative. Also, strains measured from the field test are, in most cases, smaller than those expected from the analytical results. However, when the GDF's from measured strains are compared with GDF's from analysis, it is found that the analysis results are not conservative, and in some instance, the analytical results underestimate the actual GDF's, which can lead to a groundless notion of safety. In one case, test results showed that the code GDF's specified in AASHTO LRFD is too permissive. As a result, it is found that GDF's specified in AASHTO LRFD should be used with careful reservation.

• Horticultural Science & Technology
• /
• 제31권6호
• /
• pp.666-676
• /
• 2013

The study was carried out to examine the initial point of dormancy, breaking time of internal dormancy, and to find out the accumulated hours of low temperature (under $7.2^{\circ}C$ from $0.0^{\circ}C$ to $7.2^{\circ}C$) for bud-breaking. Over-all, the chilling requirement for breaking of internal dormancy in the commercial apple cultivars ('Fuji' and 'Tsugaru') and apple cultivars bred in Korea ('Hongro', 'Sunhong', 'Honggeum', 'Hongan', 'Hongso', 'Gamhong', 'Summer dream') at the Gunwi region for 4 years (from 2009 to 2012) was investigated. Also, the breaking time of internal dormancy in the field at the Gunwi region and the breaking time of dormancy if air temperature of Gunwi region rises $4^{\circ}C$ higher than the current one were investigated using the same data. The initial point of dormancy was set at the time when the lateral bud breaking did not occurred (when heading back cutting was done in the middle of terminal shoots). The occurrence of the breaking of internal dormancy was decided if the breaking of the terminal bud of bourse shoot occurred within 15 days or not in growth chamber. About 100 bourse shoots were collected by cultivar classification in early December every year and were stored at $5.0^{\circ}C$, and they were placed in growth chamber at one week interval. The chilling requirement of cultivars was expressed in accumulated hours in the field and in the growth chamber under $7.2^{\circ}C$ and $0.0-7.2^{\circ}C$ from the initial point of dormancy to the breaking time of internal dormancy. The results showed that the initial point of dormancy in selected cultivars could occur at the end of September. The breaking time of internal dormancy could occur from the end of January to the early of February. The accumulated hours under $7.2^{\circ}C$ for breaking of internal dormancy were 1,600-2,000 hours, while those of $0.0-7.2^{\circ}C$ were 1,300-1,800 hours. In comparing the different apple cultivars, the chilling requirement of the early flowering cultivars seemed lower than that of the late-flowering cultivars. Based on these results, if the air temperature of Gunwi region rises about $4.0^{\circ}C$ higher than the current one, the breaking time of internal dormancy will be delayed by 2-4 weeks.

• Journal of radiological science and technology
• /
• 제31권4호
• /
• pp.389-399
• /
• 2008

Corrections of attenuation, scatter and resolution are important in order to improve the accuracy of single photon emission computed tomography (SPECT) image reconstruction. Especially, the heart movement by respiration and beating cause the errors in the corrections. Myocardial phantom is used to verify the correction methods, but there are many different parts in the current phantoms in actual human body. Therefore the results using a phantom are often considered apart from the clinical data. We developed a new phantom that implements the human body structure around the thorax more faithfully. The new phantom has the small mediastinum which can simulate the structure in which the lung adjoins anterior, lateral and apex of myocardium. The container was made of acrylic and water-equivalent material was used for mediastinum. In addition, solidified polyurethane foam in epoxy resin was used for lung. Five different sizes of myocardium were developed for the quantitative gated SPECT (QGS). The septa of all different cardiac phantoms were designed so that they can be located at the same position. The proposed phantom was attached with liver and gallbladder, the adjustment was respectively possible for the height of them. The volumes of five cardiac ventricles were 150.0, 137.3, 83.1, 42.7 and 38.6ml respectively. The SPECT were performed for the new phantom, and the differences between the images were examined after the correction methods were applied. The three-dimensional tomography of myocardium was well reconstructed, and the subjective evaluations were done to show the difference among the various corrections. We developed the new cardiac and torso phantom, and the difference of various corrections was shown on SPECT images and QGS results.

• The Journal of Korean Society for Radiation Therapy
• /
• 제20권1호
• /
• pp.25-29
• /
• 2008

Purpose: To monitor the changes of location of prostate gland using DIPS and to examine the adjustment and proton beam therapy depending on the movement of prostate gland in proton beam therapy for prostate gland in which a fiducial gold marker was inserted. Materials and Methods: This study was conducted in ten patients with prostate cancer who received proton beam therapy since April of 2008. To monitor the change of prostate location, three fiducial gold markers were inserted prior to the treatment. To minimize the movement of prostate gland, patients were recommended to urinate prior to the treatment, to intake a certain amount of water and to concomitantly undergo rectal balloon. In these patients, the set-up position was identical to that for a CT-simulation. The PA (posterior-anterior) and lateral images were obtained using both DIPS (digital image positioning system) and a plain radiography, and they were compared between the two imaging modalities. Thus, the changes of the location of fiducial gold marker were assessed based on three coordinates (x, y, z) and then adjusted. This was followed by proton beam therapy. Results: Images which were taken using a plain radiography were compared with those which were taken using DIPS. In ten patients, according to a reference bony marker, the mean changes of the location of fiducial gold marker based on an iso-center were X-axis: $\pm$0.116 cm, Y-axis: $\pm$0.19 cm and Z-axis: $\pm$0.176 cm. These ten patients showed a difference in the changes of location of prostate gland and it ranged between RT: 0.04 cm and RT: 0.24 cm on the X-axis; between Inf: 0.03 cm and Sup: 0.42 cm on the Y-axis; and Post: 0.05 cm and Ant: 0.35 cm on the Z-axis. Conclusion: To minimize the movement of prostate gland, as the pre-treatment prior to the treatment. In all the patients, however, three fiducial gold markers showed a daily variation which were inserted in the prostate gland. Based on the above data, Thus, the requirement of gold marker matching system depending on the daily variation in the proton beam therapy for which more accurate establishment of target was confirmed. It is assumed that an accurate effect of proton beam therapy would be enhanced by adjusting the target-center depending on the location change of prostate gland using DIPS which was used in the current study.