• 한국레이저가공학회지
• /
• 제15권3호
• /
• pp.7-10
• /
• 2012

Dimensions (line/space) of circuits in IC substrates for high-end chips (e.g. CPU, etc.) are anticipated to decrease as small as $10{\mu}m/10{\mu}m$ in 2014. Since current etch-based circuit-patterning processes are not able to address the urgent requirement from industry, laser-based circuit patterning processes are under active research in which UV laser is used to engrave embedded circuits patterns into IC substrates. In this paper, we used a nanosecond UV laser to directly fabricate embedded circuit patterns into IC substrates with/without ceramic powders. In experiments, we engraved embedded circuit patterns with dimensions (width/depth) of abut $10{\mu}m/10{\mu}m$ and $6{\mu}m/6{\mu}m$ into the IC substrates. Due to the recoil pressure occurring during ablation, the circuit patterning of the IC substrates with ceramic powders showed the higher ablation rate.

• 열처리공학회지
• /
• 제6권4호
• /
• pp.230-236
• /
• 1993

The laser beam hardening has been experimentally tried to find the hardened characteristics of STD11. Experiment was performed on the optimum hardening condition with 2kW $CO_2$ laser. The microstructure of the hardened layers was observed using the microscope. The hardened zones exhibits very high Vickers microhardness of 720 Hv, however, the deoxidation was observed under the surface of hardened area. The case depth of hardened zones is about 0.6mrn and case width is 4mm. FEM-simulation on laser surface hardening of STD11 steel are described. With the proper assumption of the absorbed energy density, the calculated case depth and width in 2 kW $CO_2$ laser hardening were in good agreement with the experimental result. It was found that there is optimum absorbed energy density of STD11.

• 한국산학기술학회논문지
• /
• 제19권10호
• /
• pp.346-351
• /
• 2018

금속 3D 프린팅 기술은 레이저 빔의 초점에 금속분말을 주입하는 방식에 따라 대표적으로 PBF(Powder Bed Fusion)방식과 DED(Direct Energy Deposition)방식으로 나뉜다. DED 방식은 금속 분말 도포와 동시에 레이저를 조사하여 3차원 구조물을 제작하는 금속 3D 프린팅 기술이고, PBF 방식은 일정 높이로 3차원 그래픽을 슬라이싱 한 후 한 층씩 금속 분말을 적층하여 레이저를 이용해 3차원 구조물을 제조하는 방식이다. DED 방식을 사용하면 레이저 클래딩, 금속 용접 등에는 강점을 가지지만 3D 형상을 제작할 경우 밀도가 낮아지는 문제점이 발생한다. DED 방식에서의 구조체 밀도 문제를 해결하기 위해 PBF 방식을 도입하면 상대적으로 밀도가 높은 3차원 구조물을 제작하는데 용이하다. 본 논문에서는 갈바노 스캐너와 광섬유로 전송되는 Nd:YAG 레이저 빔을 이용한 약 $30{\mu}m$ 크기의 스테인리스 강 분말을 이용하는 PBF 방식의 3차원 프린터를 제작하고, 이를 이용하여 얇은 금속 구조물을 제작하였다. 또한 레이저의 조사 횟수, 출력, 초점 크기, 스캐닝 속도에 따른 선폭의 최적조건을 찾았으며, 그 결과 최적 조건은 레이저 조사 횟수 2회, 출력 30 W, 초점 크기 $28.7{\mu}m$, 스캐닝 속도 200 mm/s에서 최소 선폭은 약 $85.3{\mu}m$로 측정되었다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2000년도 춘계학술대회 논문집
• /
• pp.816-819
• /
• 2000

Recently the styrofoam has been used fur material of press die pattern. The object of this research is to develope an automated laser system for manufacture of press die pattern which depends chiefly on handwork during its process. After converting 3-D CAD model into cross-sectional shape information, the unnecessary part of the section is vapored away by laser. The depth and width of cut are mainly under the control of laser power and beam feed rate. The optimum manufacturing conditions are obtained by preliminary experiments. It is necessary fur precise styrofoam pattern manufacturing to develope laser system which has sufficient motion accuracy and program or beam path generation and automatic control of this system.

• Journal of the Optical Society of Korea
• /
• 제18권4호
• /
• pp.382-387
• /
• 2014

An all-reflective, simple noncollinear second harmonic (SH) autocorrelator is described for monitoring the shot-to-shot behavior of ultrashort high-power laser pulses. Two mirrors are used for the dispersion-free splitting of a pulse into two halves. One of the mirrors is able to adjust the delay time and angle between two halves of the laser pulse in a nonlinear crystal. We present the possibility of real-time measurement of the pulse duration, peak intensity (or energy), and the pointing jitters of a laser pulse, by analyzing the spatial profile of the SH autocorrelation signal measured by a CCD camera. The measurement of the shot-to-shot variation of those parameters will be important for the detailed characterization of laser accelerated electrons or protons.

• 한국정밀공학회지
• /
• 제31권5호
• /
• pp.375-380
• /
• 2014

To enhance biocompatibility between the orthopedic implant stem and obsteoblast cells, bone-forming cells, micro-size holes are patterned in Ti plate surface. Initially, the house built laser power stabilization system is applied to the laser micro patterning machine to convince repeatable result. Various pulse widths are irradiated Ti plate and relationship between diameters of patterned holes and pulsed width is derived. Effect of multi pulse is observed and optimal pulse number is considered to avoid heat affected zone. After MG-63 osbeoblast cells are cultured, micro patterned Ti plates are compared with control plates. In SEM image, cells are well aligned and aggregation is observed in both 60, and $100{\mu}m$ patterned plates. Finally, free form surface stem model is prepared to test micro hole patterning.

• 한국레이저가공학회:학술대회논문집
• /
• 한국레이저가공학회 2004년도 추계학술대회논문집
• /
• pp.22-28
• /
• 2004

Pit and rim formation on the Acrylonitrile Butadiene Styrene(ABS) plastic surface was evaluated after it was irradiated by $CO_2$ and Nd:YAG laser beams. Our results show that thermal effect floor was well observed at the outer wall of pit with $CO_2$ laser irradiated while it was not the case with Nd:YAG laser irradiated. Also the volume and depth of pit formation increase proportionally with the energy intensities of two laser irradiations, but there are significant differences in the slope, width, and FWHM of the Pit formation with two types of laser irradiations. This result shows that $CO_2$ laser irradiation leads to better cooling contraction effect while Nd:YAG laser irradiation induces better recoil pressure effect during the interaction between ABS plastic and laser beam irradiation. The shape of the laser marking could vary significantly depending on the traveling path of molten plastic during injection molding of ABS plastic. Therefore, the selection of material and molding process can have a great impact on the performance of optical storage media.

• Current Optics and Photonics
• /
• 제2권6호
• /
• pp.582-588
• /
• 2018

A $Nd:YVO_4$ laser dual-end-pumped by a wavelength-locked 878.6 nm laser diode is presented. At the repetition rate of 500 KHz, the absorbed pump power of 58 W, an output power of 26.1 W at 1064 nm is obtained, corresponding to an optical-optical efficiency of 45%. The pulse width is 44.2 ns. Meanwhile, the effects of traditional 808 nm pumping and 878.6 nm dual-end-pumping on the output laser beam quality and pulse width are compared and analyzed in an experiment.

• Journal of Welding and Joining
• /
• 제22권6호
• /
• pp.19-24
• /
• 2004

The laser welding and its analysis of thin-sheet carbon steels were carried out with high power $CO_{2}$ laser. The main factor of weld quality of laser welding is gap and edge quality. This work was preformed to focus on the gap tolerance problem during laser welding. First, bead on plate welding of thin sheet was examined to investigate the effect of laser welding variables, and to obtain optimum welding condition. Butt welding was also carried out to show the effect of gap on the laser weldability of thin sheet. In order to investigate the effect of gap on formability of welded thin sheet, LDH test was caried out. At high welding speed, the partial penetration was obtained by low heat input. Otherwise, porosity was formed in the bead at low weld speed because of too much heat input. The optimum welding condition of welding was derived from bead width, penetration and hardness property. The maximum gap tolerance on laser welding was observed to be about 0.2mm. This gap size has good relationship with beam size of laser spot(about 0.3mm). The formability of welded sheet was about $80{\%}$ value of base metal and the gap size has not affected on the formability, although weld quality is dependent on the gap size.

• Journal of Advanced Marine Engineering and Technology
• /
• 제40권9호
• /
• pp.768-773
• /
• 2016

엔진 밸브 시트와 페이스는 엔진 성능에 영향을 미치므로 내마모성, 내열성 및 내식성이 요구된다. 이러한 특성을 갖는 표면층을 형성하기 위해 일반적으로 PTA 프로세스를 사용하고 있지만 넓은 열 영향부와 높은 모재 희석 등과 같은 문제가 발생한다. 이러한 단점을 개선한 레이저 클래딩은 희석률이 낮고 열 영향 및 열 변형을 최소화하므로 더욱 우수한 클래드 층을 형성할 수 있다. 하지만 레이저 빔의 특성상 넓은 면적을 클래딩 할 경우, 1 패스 클래드 층의 중첩이 불가피하다. 중첩률 기준을 빔 사이즈와 클래드 층 폭으로 나누어 멀티패스 클래드 층을 형성한 결과, 기준에 관계없이 중첩률이 증가할수록 클래드 층의 폭이 감소하고 높이가 증가하였다. 하지만 빔 사이즈 기준 중첩률 조건으로 형성된 멀티패스 클래드 층이 다른 기준보다 모재 희석이 감소하여 더욱 높은 경도 값을 나타내었다. 결론적으로, 중첩률 기준을 클래드 층 폭으로 할 경우, 클래드 층 형상에 영향을 주는 공정변수가 변할 때 마다 폭의 길이가 달라지기 때문에 빔 사이즈를 중심으로 중첩률을 정의하였다.