• Steel and Composite Structures
• /
• 제25권5호
• /
• pp.603-615
• /
• 2017

This experimental research presents the seismic performance of steel reinforced high-strength concrete (SRHC) short columns. Eleven SRHC column specimens were tested under simulated earthquake loading conditions, including six short column specimens and five normal column specimens. The parameters studied included the axial load level, stirrup details and shear span ratio. The failure modes, critical region length, energy dissipation capacity and deformation capacity, stiffness and strength degradation and shear displacement of SRHC short columns were analyzed in detail. The effects of the parameters on seismic performance were discussed. The test results showed that SRHC short columns exhibited shear-flexure failure characteristics. The critical region length of SRHC short columns could be taken as the whole column height, regardless of axial load level. In comparison to SRHC normal columns, SRHC short columns had weaker energy dissipation capacity and deformation capacity, and experienced faster stiffness degradation and strength degradation. The decrease in energy dissipation and deformation capacity due to the decreasing shear span ratio was more serious when the axial load level was higher. However, SRHC short columns confined by multiple stirrups might possess good seismic behavior with enough deformation capacity (ultimate drift ratio ${\geq}2.5%$), even though a relative large axial load ratio (= 0.38) and relative small structural steel ratio (= 3.58%) were used, and were suitable to be used in tall buildings in earthquake regions.

• 한국지반공학회논문집
• /
• 제34권4호
• /
• pp.13-25
• /
• 2018

앵커가 보강된 비탈면에 활동이 발생한 경우에는 활동면을 따라 전단면에 전단응력과 휨 응력이 작용하게 되고, 전단변형의 증가는 앵커의 긴장력 변화를 야기한다. 본 연구에서는 전단에 따른 앵커의 긴장력 변화를 확인하기 위해 앵커의 수직방향으로 전단변형을 유발하여 앵커의 긴장력을 측정하는 방법으로 대형 직접전단시험기를 통해 전단시험을 수행하였다. 전단시험은 앵커 설치 유무, 정착부에서 전단면까지의 이격거리(1D, 2D, 4D) 및 측압(0.1MPa, 0.2MPa)을 변수로 총 8가지 조건에 대해 시험을 실시하였다. 전단시험 결과, 이격거리와 주변지반의 측압은 앵커가 설치된 모형 지반의 전단력 및 앵커의 긴장력에 영향을 미치는 것으로 나타났으며, 전단력 변화는 앵커 두부 및 선단부의 축력변화와 관련이 있음을 규명하였다. 따라서 앵커 두부에서의 긴장력 변화 경향을 분석함으로써, 간접적으로 앵커 정착부에서의 전단변형에 따른 거동을 예측할 수 있음을 확인하였다.

• 한국지반신소재학회논문집
• /
• 제8권4호
• /
• pp.27-34
• /
• 2009

본 연구에서는 토목섬유가 층상으로 보강된 슬래그 재료의 전단강도와 변형특성을 다루었다. PET mat와 같은 토목섬유에 의한 보강이 슬래그의 전단강도와 변형특성에 미치는 영향을 조사 및 분석하기 위해 압밀배수 조건 하에서의 대형삼축압축시험을 수행하였다. 연구에 사용된 슬래그 재료는 현장에서 사용되는 재료와 동일한 재료로서 scale effect로 인한 문제점은 없었다. 토목섬유로 보강된 슬래그의 응력-변형율 거동은 무보강시 보다 다일러턴시의 양이 작고, 축변형율 증가시 항복 이후에도 축차응력이 증가하는 변형율경화(strain hardening) 거동을 나타내었다. 토목섬유로 보강된 슬래그 재료의 겉보기 점착력과 내부마찰각 등의 강도정수는 보강되지 않은 경우의 값보다 1.2-1.4배 정도 크고, 구속압 수준이 클수록 커지는 것으로 나타났다. 따라서 슬래그를 사용한 제방의 설계나 시공시 슬래그 재료에 토목섬유를 층상으로 보강하여 사용할 경우에는 강도증가 효과에 의해 안전율을 향상시킬 수 있을 것으로 기대된다.

• 한국지진공학회:학술대회논문집
• /
• 한국지진공학회 1999년도 춘계 학술발표회 논문집 Proceedings of EESK Conference-Spring
• /
• pp.69-76
• /
• 1999

Because of the limited land in Korea most of the projects require large-scale reclamation. The hydraulic-filled soil deposits are usually loose and susceptible to be liquified during earthquake. The dynamic deformation characteristics which expressed by shear modulus and damping ratio are important to analyze the earthquake ground motion. In this paper resonant column tests were performed on five hydraulic filled soil in Korea and the deformational characteristics at both small and medium strains were investigated. The coefficients in the Hardin equation to predict the representative maximum shear modulus and modulus reduction cure are also proposed.

• Structural Engineering and Mechanics
• /
• 제73권5호
• /
• pp.529-542
• /
• 2020

As limited well-documented experimental data are available for assessing the attributes of different deformation components of flanged walls, few appropriate models have been established for predicting the inelastic responses of flanged walls, especially those of asymmetrical flanged walls. This study presents the experimental results for three large-scale T-shaped reinforced concrete walls and examines the variations in the flexural, shear, and sliding components of deformation with the total deformation over the entire loading process. Based on the observed deformation behavior, a simple model based on moment-curvature analysis is established to estimate flexural deformations, in which the changes in plastic hinge length are considered and the deformations due to strain penetration are modeled individually. Based on the similar gross shapes of the curvature and shear strain distributions over the wall height, a proportional relationship is established between shear displacement and flexural rotation. By integrating the deformations due to flexure, shear, and strain penetration, a new load-deformation analytical model is proposed for flexure-dominant flanged walls. The proposed model provides engineers with a simple, accurate modeling tool appropriate for routine design work that can be applied to flexural walls with arbitrary sections and is capable of determining displacements at any position over the wall height. By further simplifying the analytical model, a simple procedure for estimating the ultimate displacement capacity of flanged walls is proposed, which will be valuable for performance-based seismic designs and seismic capacity evaluations.

• 한국공작기계학회논문집
• /
• 제11권4호
• /
• pp.26-33
• /
• 2002

One characteristic of Fine-Blanking is that the size and the direction of stress and strain are very complex in the plastic flow according to the condition of blanking. Especially, they are affected by the clearance of punch and die, by the force of blanking holder and by the force of counter punch. The purpose of this research is to how the deformation behavior in shear zone more clearly, based on Green & Cauch's large deformation theory. The deformation behavior and cracks were investigated in each step of shear, according to punch penetration increase, the use of V-indenter ring and the hardness of materials. This research found that the transforming behavior was the same as pure discretion and the cracks could be prevented when hardness is low.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2001년도 춘계학술대회 논문집
• /
• pp.176-179
• /
• 2001

A simple cold pressing procedure which allows shear deformations on sheet metals is proposed by designing dies with grooves and applied to aluminum 3003 sheets. shear deformation led to the formation of preferred orientation along <100>//RD, and the effect of initial tortures on the formation of shear textures was also studied Rectangular shaped dislocation cells formed in the deformed microstructure and boundaries of dislocation cells gradually rounded with the increased plastic strain. Upon subsequent annealing textures inherited deformation textures. Recrystallized grains consisted of a large number of fully recovered subgrains with well defined boundaries which persisted even after annealing at a higher temperature.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2008년도 추계학술대회A
• /
• pp.1718-1722
• /
• 2008

This study explores the influence of volume fraction of nanocrystals of Cu-Zr amorphous alloys on shear band formation. As the number of crystals with very tiny size increases, the strain localization, i.e. shear band, decreases without large drop of flow stress. The DPRs also depict no sudden drop and relatively high values. The strain state during the deformation represents a few shear bands at low volume fraction while there are no distinguishable shear bands at high volume fraction of nanocrystals.

• 한국철도학회논문집
• /
• 제15권6호
• /
• pp.623-630
• /
• 2012

궤도하부층의 지지강성을 확보하기 위하여 설치하는 강화노반은 통상 일정 입도분포의 쇄석재료로 구성된다. 이러한 강화노반은 통과톤수의 누증 즉, 과도한 열차하중이 반복적으로 가해질 경우 영구변형이 발생할 수 있으며 이러한 영구변형은 궤도틀림의 한 원인이 될 수 있다. 또한 강화노반 재료의 적정두께를 확정하기 위해서는 이러한 영구변형 특성을 파악하는 것이 중요하다. 본 연구에서는 국내 강화노반 재료로 사용될 가능성이 높은 M-40 쇄석재료를 선정하여 대형반복삼축시험을 실시하여 재료의 회복탄성 특성과 영구변형 특성을 분석하였다. 시험으로부터 임의 전단응력비 및 반복재하횟수에 따른 회복탄성계수 특성과 영구변형 발생특성을 분석하였으며 M-40 쇄석강화노반 재료의 영구변형에 영향을 미치는 인자(반복재하횟수, 구속압, 전단응력비, 탄성계수 등)를 함께 고려할 수 있는 영구변형 예측모델을 제시하였다.

• Structural Engineering and Mechanics
• /
• 제84권3호
• /
• pp.311-321
• /
• 2022

In the buildings with long spans and high floors, such as logistics warehouses and semiconductor factories, it is difficult to install supporting posts under beams during construction. Therefore, the size of structural members becomes larger inevitably, resulting in a significant increase in construction costs. Accordingly, a prestressed hybrid wide flange (PHWF) beam with hollowed steel webs was developed, which can reduce construction costs by making multiple openings in the web of the steel member embedded in concrete. However, since multiple openings exist and prestress is introduced only into the bottom flange concrete, it is necessary to identify the shear resistance mechanism of the PHWF beam. This study presents experimental shear tests of PHWF beams with hollowed steel webs. Four PHWF beams with cast-in-place (CIP) concrete were fabricated, with key variables being the width and spacing of the steel webs embedded in the concrete and the presence of shear reinforcing bars, and web-shear tests were conducted. The shear behavior of the PHWF beam, including crack patterns, strain behavior of steel webs, and composite action between the prestressed bottom flange and CIP concrete, were measured and analyzed comprehensively. The test results showed that the steel web resists external shear forces through shear deformation when its width is sufficiently large, but as its width decreased, it exerted its shear contribution through normal deformation in a manner similar to that of shear reinforcing bars. In addition, it was found that stirrups placed on the cross section where the steel web does not exist contribute to improving the shear strength and deformation capacity of the member. Based on the shear behavior of the specimens, a straightforward calculation method was proposed to estimate the web-shear strength of PHWF beams with CIP concrete, and it provided a good estimation of the shear strength of PHWF beams, more accurate than the existing code equations.