• 한국생활과학회지
• /
• 제11권3호
• /
• pp.273-285
• /
• 2002

Three materials for sport underwear were manufactured by order for study, and among them, suitable material in order to perform an experiment on the effect of wearing was adopted. The results are as follows: The result of wearing an experimental clothes for sports manufactured as a foundation-type underwear for sports showed that if the same compositional materials were applied, laminating material had higher rate than that of others in the amount of sweat. Concerning relative humidity in clothes and the amount of sweat absorbed in clothes among the two kinds of materials which were produced by laminate, material 2(nylon+modal) was statistically exerts higher influence on the amount of sweat. The humidity in clothes keeps the optimal condition of 59.8%, and breast part showed the highest relative humidity. The material 2(nylon+modal) showed the highest comfortableness, the sense of warmth, humidity and voluminousness, and the sense of pressure. Follow-up survey revealed that in case of material 2, higher amount of sweat than that of the group objects in its early phase, and the amount of sweat varies from individuals. The temperature in clothes of folded parts of experimental clothes and maximum surface temperature was equivalent to that of average skin. With the lapse of time, the weight decreased of 11.03% in maximum, and 3.12% in minimum. The amount of change in the girth was greater in part of body frame than that of limbs, and especially, navel and waist part showed high decrease, and upper breast, breast and the largest part of abdomen showed relatively low decrease. The above experiment revealed that materials for suitable to the underwear for sports for loss of weight by an exercise should be made of doubled-nylon and modal, along with the laminate processing, which heightens the amount of sweat. Thus, wearing an experimental wear gave satisfaction in the view of the beauty of appearance as it did not discharge flowing secretion to the outside at the time of exercise.

• International Journal of Aeronautical and Space Sciences
• /
• 제15권1호
• /
• pp.32-43
• /
• 2014

Automatic fiber placement (AFP) has become a popular processing technique for composites in the aerospace industry, due to its ability to place prepregs or tapes precisely in the exact position when complex parts are being manufactured. This paper presents the design, analysis, and manufacture of an AFP mandrel for composite aircraft fuselage skin fabrication. According to the design requirements, an AFP mandrel was developed and a numerical study was performed through the finite element method. Linear static load analyses were performed considering the mandrel structure self-weight and a 2940 N load from the AFP machine head. Modal analysis was also performed to determine the mandrel's natural frequencies. These analyses confirmed that the proposed mandrel meets the design requirements. A prototype mandrel was then manufactured and used to fabricate a composite fuselage skin. Material load tests were conducted on the AFP fuselage skin curved laminates, equivalent flat AFP, and hand layup laminates. The flat AFP and hand layup laminates showed almost identical strength results in tension and compression. Compared to hand layup, the flat AFP laminate modulus was 5.2% higher in tension and 12.6% lower in compression. The AFP curved laminates had an ultimate compressive strength of 1.6% to 8.7% higher than flat laminates. The FEM simulation predicted strengths were 4% higher in tension and 11% higher in compression than the flat laminate test results.

• 한국자동차공학회논문집
• /
• 제25권3호
• /
• pp.350-359
• /
• 2017

This paper presents a new holistic development approach for the carbon continuous-fiber composite frame of an automotive sunroof assembly. The original steel frame has been designed to get higher bending stiffness with its corrugated cross-sectional shape. The new approach uses the prepregs of a fast cure epoxy and PCM manufacturing processing. For higher productivity, the new frames feature a very simple plat cross sectional shape but achieve high bending stiffness through the laminate design. The sandwich structure with a PET foam core was presented. The frames were made of carbon UD laminae covered single carbon fabric on the outer surfaces. The fabrics provide torsional stiffness and also hold the carbon UD fibers floating in the low viscous epoxy resin of prepregs at the curing temperature during processing. The final product yields approximately 18 % savings in weight compared with the original.

• International Journal of Ocean System Engineering
• /
• 제3권1호
• /
• pp.38-43
• /
• 2013

Wind turbine generator is, recently, becoming bigger and bigger. So, in order to produce large amounts of electricity generation, we have to consider the length and thickness of the blade. We investigated the skills of processing for making the super thickness laminate through development fabrication process for high speed curing composite heating table.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.42-45
• /
• 2003

The purpose of this study is the development or the extensive Rapid Prototyping Technique. which can resolve the long-term manufacturing process, shrinkage and deformation occurring rapid prototyping technique. To begin with. the various specimens for tensile were manufactured on the basis of this modeling technology. Then, many kinds of the laminate pieces for the test were made by using the sheet metals lmm and 1.5mm thickness which is composed of the same ingredient. The tensile specimen were manufactured by changing the process variables, Such as electric current, pressure and resistance welding time for the Rapid Prototyping with metal sheet. And then by using the Taguchi method. The interrelation between the specimen and mechanical properties were determined and the system for the optimum process variable organized.

• Journal of Mechanical Science and Technology
• /
• 제14권5호
• /
• pp.477-482
• /
• 2000

This study discusses a non-contact optical technique (electronic speckle pattern interferometry) that is well suited for thermal deformation measurement without any surface preparation and compensating process. Fiber reinforced plastics ($[0]_{16},\;[0/90]_{8S}$) were analyzed by ESPI to determine their thermal expansion coefficients. The thermal expansion coefficient of the transverse direction of a uniaxial composite is evaluated as $48.78{\times}10^{-6}(1/^{\circ}C)$. Also, the thermal expansion coefficient of the cross-ply laminate $[0/90]_{8S}$ is numerically estimated as $3.23{\times}10^{-6}(1/^{\circ}C)$ that is compared with that measured by ESPI.

• 한국화재소방학회논문지
• /
• 제29권4호
• /
• pp.49-56
• /
• 2015

본 연구에서는 건물 실내에서 주로 사용되고 있는 합판, 실내 마감용 목재(루바; 소나무), 압축 스티로폼 단열재, 강화마루 및 PVC 장판 5 종류의 연소가스 유해성을 분석하였다. 연소가스의 유해성 분석은 Naval Engineering Standard(NES) 713 규격 및 미국국방성 규격(MIL-DTL)을 적용하였다. $CO_2$의 방출량은 5종의 내장재 모두 NES 713 규격 한계치인 100,000 ppm을 초과하지 않았다. CO 방출량의 경우 압축 스티로폼 단열재가 6,098 ppm으로 규격 한계치인 4,000 ppm을 초과하는 값을 나타내었다. 포름알데히드는 PVC 장판과 압축 스티로폼 단열재에서 각각 25 ppm, 49 ppm 방출되었다. $NO_X$는 합판에서 955 ppm으로 가장 높은 양이 방출되었으며, 규정 한계치 250 ppm에 비하여 높은 값으로 나타났다. 독성 지수는 합판 5.19, PVC 장판 4.13, 압축 스티로폼 단열재가 2.35, 강화마루 2.34, 그리고 실내 마감용 목재 1.22로 산출되었다. 본 연구에서는 화재 시 발생되는 연소가스 측정 및 유해가스 농도를 확인하여, 향후 건축 내장재의 화재 안전성을 평가하기 위한 기초 데이터로 활용하고자 한다.

• 융합정보논문지
• /
• 제9권7호
• /
• pp.33-40
• /
• 2019

최근 항공 관련 산업이 활성화됨에 따라 복합재 해석 소프트웨어의 범용화가 요구되고 있다. 지금까지는 복합재 해석에 상용 소프트웨어를 주로 사용해 왔으나 고가의 가격과 제한적인 기능으로 인해 사용에 어려움을 겪어왔다. 이런 문제를 해결하기 위해 해석 절차를 모두 온라인화하고 범용화한 면내 및 코너 부외 파손 자동 해석 소프트웨어가 최근에 개발되었다. 그러나 이들은 다중의 파손 기준으로 동시에 해석할 수 없는 단점이 있었다. 본 논문에서는 CUDA 코어를 장착한 GPU에서만 동작하는 병렬 처리 플랫폼을 이용하여 다중의 파손 기준에 대한 해석을 동시에 처리하면서 처리 속도를 획기적으로 향상시키는 방법을 제안한다. 방대한 구조물 데이터에 대해서 해석 처리 속도를 실험하였을 때 만족할 만한 결과를 얻었다.

• 한국정밀공학회지
• /
• 제32권9호
• /
• pp.773-779
• /
• 2015

The laser Powder Bed Fusion (PBF) system is currently recognized as a leading process. Due to the various materials employed such as thermoplastic, metal and ceramic composite powder, the application's use extends to machinery, automobiles, and medical devices. The PBF system's surface quality of prototypes and processing time are significantly affected by several parameters such as laser power, laser beam size, heat temperature and laminate thickness. In order to develop a more elaborate and rapid system, this study developed a new PBF system and sintering process. It contains a 3-axis dynamic focusing scanner system that maintains a uniform laser beam size throughout the system unlike the $f{\theta}$ lens. In this study, experiments were performed to evaluate the effects of various laser scanning parameters and fabricating parameters on the fusion process, in addition to fabricating various 3D objects using a PA-12 starting material.

• 한국가구학회지
• /
• 제23권1호
• /
• pp.26-37
• /
• 2012

This is the study about the New Formation Developement, the Changeable Table Design with Units that made of Wasted Wood to use restricted material rationally and to improve the space efficiency in the Table Design. We made some changeable table design with units that made of laminated wood wasted. And we found out the following formative characteristic and physical merits through this study. First, the space efficiency can be improve technically through the unit combination and organic transfomation of the specific form and a new method by laminated wood make the personal originality and the structral stability be built up. Second, there are some merits, moveable convenience and variable layout by the combination or transformation or personal fondness so that economical efficiency and variable of design can be improved. Third, we can remove original faults inside wood like a knot or not-uniform of wood organ when we laminate wood so that we use proper units that have original beauty of wood and can represent mild mood of furniture wholly. Fourth, much more strengthen tensile strength by the reciprocal action among the units that be made of laminated wood reduces wood's metamorphosis like bending or twisting so that the uniformity of wood can be gain and furniture's metamorphosis can be reduced. According to changes of nature environment, the difficulty of supply and demand for wood may be happen. According to changes of life style these days, supply and demand for environment friendly material, processing technique and developement of design to improve the efficiency of using space must be very important factor in morden furniture design. So we propose changeable furniture design by using new environment friendly meterial and processing method from this study.