• Korean Educational Research Journal
• /
• v.38 no.3
• /
• pp.167-188
• /
• 2018

The purpose of this study is to suggest safety education on life science inquiry activity, which subjects on the exploration and autonomous research to the relevant topics, mainly done by the science high school students. Investigation was made on subjects of research activity proposed from Life science and autonomous research from science high school students by examine thoroughly 2009 revised education curriculum. To prevent school laboratory accidents, education of basic safety regulations and general precautions should be repeatedly notified by clear statements and expression to each topic. Expressing the safety factors considering the themes of autonomous inquiry and activities presented in the course of education should be done, so that students should not experience laboratory accidents by reason of ignorance. From the beginning of organization to performing research, safety rules about disposing chemicals and tools wastes occurring during research should be noticed and expressed in precautions following waste disposal system should be adopted. It is necessary to level up the accessibility of information about the laboratory safety rules to confirm to the every student, and also ensure the takeover of the clean-up and use of utilities at the time of search end in order to prevent the incidence of laboratory accidents during the thorough stages of biological inquiry activities.

• Journal of the Korean Society of Safety
• /
• v.38 no.6
• /
• pp.79-87
• /
• 2023

This study focuses on safety behavior among research workers and investigates the factors influencing their safety behavior. The selected variables for examining their impact on researchers' safety behavior are safety leadership, safety climate, and safety motivation. Surveys were conducted to analyze the structural equation modeling among these variables. The results indicate that the safety leadership of research supervisors positively influences the creation of a safety climate in research laboratories. Additionally, the safety climate positively impacts research workers' safety motivation and behavior. Therefore, to enhance the safety behavior of research workers, it is necessary to strengthen safety leadership education to improve the safety leadership of laboratory supervisors. The laboratory can enhance its safety climate by implementing management policies and safety regulations, fostering communication among members, and providing safety education.

• Journal of Technologic Dentistry
• /
• v.38 no.3
• /
• pp.209-216
• /
• 2016

Purpose: The purpose of this study is to discover the recognition of dental technicians on MSDS and to research the furnishing rate of Material Safety Data Sheet (MSDS) in dental laboratories. Method: 104 dental technicians who were self-written questionnaire. The results were analyzed by SPSS 12.0. The answers to the questionnaire underwent frequency analysis, chi-square test were performed. Results: The result of cross analysis on the occurrence of occupational diseases according to whether MSDS is furnished showed that the group with MSDS furnished had 37.8% of damages due to their occupation, but the group with MSDS unfurnished had 65.7% of damages due to their occupation, which displayed a significant difference(p<0.05). The result of cross analysis on whether the education about chemicals according to whether MSDS is furnished showed there were relatively more responses of no education on the types and characteristics of chemicals, the effect on human body and its risk, emergency measure when exposed to risk, the treating and storing methods and the disposal methods. In addition, there were significant differences on whether all the above education was done between the group with MSDS furnished and the group without MSDS(p<0.000). Conclusion: In order to secure safe working environment of dental technicians and to reduce occurrence of damage caused by chemicals, the related education is necessary. The recognition of dental technicians on MSDS and furnishing rate is increasing but still insufficient, so the related organizations need to establish education and PR measures for prevention of damage.

• Journal of the Korean Society of Safety
• /
• v.29 no.6
• /
• pp.22-27
• /
• 2014

The market of performance arts industry such as concert, musical and opera etc is now expanding in Korea. However, the inadequate safety management in theatres often causes some accidents. The guarantee of safety in theatres is very important since the accidents in theaters can lead to many casualties and serious property damages. In particular, the small theatres which have no obligation of safety inspection by law are very vulnerable to safety mattes. This study has done the research into the improvement of safety in small theaters through the inspection and analysis of their safety status. For the purpose, this study has inspected and analyzed the safety status of small theaters over 120 in the field of theater management and operation, fire protection, electrical facilities, ceiling structure and etc. Moreover, this study had investigated the law and technical standards related to theatre safety. This study shows that the essentials to make sure of the safety in small theaters are (1) the education to improve the sense of security of people who work in theaters (2) the training to strengthen the operating skills of the facilities in theaters (3) the cooperation and support of the related organization such as technical research center, central and local government.

• Asian-Australasian Journal of Animal Sciences
• /
• v.31 no.6
• /
• pp.835-841
• /
• 2018

Objective: The aim of this study was to investigate the reversibility and safety of KISS1 metastasis suppressor (KISS1) gene vaccine in immunocastration. Methods: Six eight-week old ram lambs were randomly divided into vaccinated and control groups. The vaccine (1 mg/ram lamb) was injected at weeks 0, 3, and 6 of the study. Blood samples were collected from the jugular vein before primary immunization and at weeks 2, 4, 6, 10, 14, 22, and 30 after primary immunization. All ram lambs were slaughtered at 38 weeks of age, and samples were collected. Results: The specific anti-KISS1 antibody titers in vaccinated animals were significantly higher and the serum testosterone level was significantly lower than those in the control groups from week 4 to 14 after primary immunization (p<0.05). No significant difference was observed at weeks 22 and 30 after the primary immunization. Similar results were also found for scrotal circumference, testicular weight, length, breadth, and spermatogenesis in seminiferous tubules in week 30 after primary immunization. KS (KISS1-hepatitis B surface antigen S) fusion fragment of KISS1 gene vaccine was not detected in host cell genomic DNA of 9 tissues of the vaccinated ram lambs by polymerase chain reaction. Conclusion: The effects of KISS1 gene vaccine in immunocastration were reversible and no integration events were recorded.

• Earthquakes and Structures
• /
• v.7 no.2
• /
• pp.179-199
• /
• 2014

The steel tube-reinforced concrete (ST-RC) composite column is a novel type of composite column, consisting of a steel tube embedded in reinforced concrete. The objective of this paper is to investigate the effect of cumulative damage on the seismic behavior of ST-RC columns through experimental testing. Six large-scale ST-RC column specimens were subjected to high axial forces and cyclic lateral loading. The specimens included two groups, where Group I had a higher amount of transverse reinforcement than Group II. The test results indicate that all specimens failed in a flexural mode, characterized by buckling and yielding of longitudinal rebars, failure of transverse rebars, compressive crushing of concrete, and steel tube buckling at the base of the columns. The number of loading cycles was found to have minimal effect on the strength capacity of the specimens. The number of loading cycles had limited effect on the deformation capacity for the Group I specimens, while an obvious effect on the deformation capacity for the Group II specimens was observed. The Group I specimen showed significantly larger deformation and energy dissipation capacities than the corresponding Group II specimen, for the case where the lateral cyclic loads were repeated ten cycles at each drift level. The ultimate displacement of the Group I specimen was 25% larger than that of the Group II counterpart, and the cumulative energy dissipated by the former was 2.8 times that of the latter. Based on the test results, recommendations are made for the amount of transverse reinforcement required in seismic design of ST-RC columns for ensuring adequate deformation capacity.

• Steel and Composite Structures
• /
• v.12 no.1
• /
• pp.31-51
• /
• 2012

Local buckling can be ignored for hot-rolled ordinary strength steel equal angle compression members, because the width-to-thickness ratios of the leg don't exceed the limit value. With the development of steel structures, Q420 high strength steel angles with the nominal yield strength of 420 MPa have begun to be widely used in China. Because of the high strength, the limit value of the width-to-thickness ratio becomes smaller than that of ordinary steel strength, which causes that the width-to-thickness ratios of some hot-rolled steel angle sections exceed the limit value. Consequently, local buckling must be considered for 420 MPa steel equal angles under axial compression. The existing research on the local buckling of high strength steel members under axial compression is briefly summarized, and it shows that there is lack of study on the local buckling of high strength steel equal angles under axial compression. Aiming at the local buckling of high strength steel angles, this paper conducts an axial compression experiment of 420MPa high strength steel equal angles, including 15 stub columns. The test results are compared with the corresponding design methods in ANSI/AISC 360-05 and Eurocode 3. Then a finite element model is developed to analyze the local buckling behavior of high strength steel equal angles under axial compression, and validated by the test results. Following the validation, a finite element parametric study is conducted to study the influences of a range of parameters, and the analysis results are compared with the design strengths by ANSI/AISC 360-05 and Eurocode 3.

• Wind and Structures
• /
• v.37 no.4
• /
• pp.303-314
• /
• 2023

In this study, two steady RANS turbulence models (SST k-ω and Realizable k-ε) and four unsteady turbulence models (URANS SST k-ω and Realizable k-ε, SST-SAS, and SST-IDDES) are evaluated with respect to their capacity to predict crosswind characteristics on high-speed trains (HSTs). All of the numerical simulations are compared with the wind tunnel values and LES results to ensure the accuracy of each turbulence model. Specifically, the surface pressure distributions, time-averaged aerodynamic coefficients, flow fields, and computational cost are studied to determine the suitability of different models. Results suggest that the predictions of the pressure distributions and aerodynamic forces obtained from the steady and transient RANS models are almost the same. In particular, both SAS and IDDES exhibits similar predictions with wind tunnel test and LES, therefore, the SAS model is considered an attractive alternative for IDDES or LES in the crosswind study of trains. In addition, if the computational cost needs to be significantly reduced, the RANS SST k-ω model is shown to provide relatively reasonable results for the surface pressures and aerodynamic forces. As a result, the RANS SST k-ω model might be the most appropriate option for the expensive aerodynamic optimizations of trains using machine learning (ML) techniques because it balances solution accuracy and resource consumption.

• Journal of the Korean Society of Safety
• /
• v.27 no.2
• /
• pp.127-133
• /
• 2012

This paper shows survey result on safety management status of laboratories in Korea. In Korea, many studies and reports on laboratory safety have been published since the ministry of education, science and technology (MEST) enforced the Act on Establishing a Safe Environment of Laboratories (Lab Safety Act) in 2006. The MEST has surveyed status of safety management in institutions subject to Lab Safety Act in 2008 and 2010. According to the survey result, safety management status of universities and colleges has been improved on several factors such as establishment of safety manual and implementation of safety inspection; while the number of safety managers of universities and colleges have increased. However, the difficulties in performing duties of safety managers has increased because the number of exclusive safety managers has decreased. This paper identifies the similarities and differences between Occupational Safety and Health Act and Lab Safety Act on assignment and duties of safety managers; therefore, this paper suggests a standard to determine the number of safety managers and decide whether or not their duties should be exclusive. Besides current standard that is based on the number of researchers, the number of individual laboratories should be considered. The new method would be helpful to determine the number of exclusive safety managers because the amount of safety managers' duties generally do not depend on only the number of people who may be exposed to any risk but also the number of facilities that may be cause of any accident.

• Journal of the Korea Safety Management & Science
• /
• v.9 no.4
• /
• pp.63-70
• /
• 2007

There are something unreasonable, unsatisfactory on the law system for laboratorial safety enforced by the government from April 2006. Therefore, the system should be reviewed and revised to be satisfactory for current research condition. This study is to analyze research areas for improving laboratorial safety and to show safer ideas. With more detail, more practically improving ideas have been shown for systemizing safety assessment in advance, effective organization of laboratory, safety committee and their regulation. It is expected that better safety level all the concerned engagement, reasonable revision of safety regulation of laboratory, can be made by this research result.