• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.2
• /
• pp.165-173
• /
• 2019

Lithium anodes (13, 15, 17, and 20 wt% Li) were fabricated by mixing molten lithium and iron powder, which was used as a binder to hold the molten lithium, at about $500^{\circ}C$ (discharge temp.). In this study, the effect of applied pressure and lithium content on the discharge properties of a thermal battery's single cell was investigated. A single cell using a Li anode with a lithium content of less than 15 wt% presented reliable performance without any abrupt voltage drop resulting from molten lithium leakage under an applied pressure of less than $6kgf/cm^2$. Furthermore, it was confirmed that even when the solid electrolyte is thinner, the Li anode of the single cell normally discharges well without a deterioration in performance. The Li anode of the single cell presented a significantly improved open-circuit voltage of 2.06 V, compared to that of a Li-Si anode (1.93 V). The cut-off voltage and specific capacity were 1.83 V and $1,380As\;g^{-1}$ (Li anode), and 1.72 V and $1,364As\;g^{-1}$ (Li-Si anode). Additionally, the Li anode exhibited a stable and flat discharge curve until 1.83 V because of the absence of phase change phenomena of Li metal and a subsequent rapid voltage drop below 1.83 V due to the complete depletion of Li at the end state of discharge. On the other hand, the voltage of the Li-Si anode cell decreased in steps, $1.93V{\rightarrow}1.72V(Li_{13}Si_4{\rightarrow}Li_7Si_3){\rightarrow}1.65V(Li_7Si_3{\rightarrow}Li_{12}Si_7)$, according to the Li-Si phase changes during the discharge reaction. The energy density of the Li anode cell was $807.1Wh\;l^{-1}$, which was about 50% higher than that of the Li-Si cell ($522.2Wh\;l^{-1}$).

• Analytical Science and Technology
• /
• v.24 no.1
• /
• pp.10-14
• /
• 2011

This study was performed to compare international analytical methods of bromide and applied to determine bromide in bottled mineral water and raw ground water in Korea. Bromide in water was eluted by 10~50 mM potassium hydroxide (KOH) and determined by ion chromatography-suppressed conductivity detector (IC-CD). Sample was purified with Ba- and H-on-guard cartridge and $0.2\;{\mu}m$ membrane filter. The method detection limit (MDL) and the limit of quantitation (LOQ) of bromide were 0.2 and $0.5\;{\mu}g/L$, respectively. The calibration curve showed good lineality above 0.9993 in the ranges of the $0.5\sim80\;{\mu}g/L$. A correlation coefficient of bromide in ground water and sum of bromide and bromate in bottled mineral water is 0.808.

• Journal of Chest Surgery
• /
• v.41 no.1
• /
• pp.55-60
• /
• 2008

Background: Circulating levels of brain natriuretic peptide (BNP) provide prognostic information for patients with heart failure. The aim of our study was to investigate whether preoperative and postoperative BNP levels could predict postoperative complications and outcomes in patients after coronary artery bypass graft (CABG). Material and Method: Data was collected prospectively on 30 patients (M/F=19/11, age $60.0{\pm}9.6$ years) undergoing conventional CABG during a 1-year period beginning on January 1, 2005. Patients underwent off-pump CABG, and combined surgery was excluded. The BNP assay was performed preoperatively, immediate postoperatively at the intensive care unit (ICU), and 1, 3, 5, and 7days postoperatively. Result: Preoperative BNP levels significantly correlated with preoperative echocardiographic ejection fraction and an ICU stay of 5 days or more (r=-0.4, p=0.028; r=0.39, p=0.031, respectively). A preoperative BNP cut-off value above 263 pg/mL demonstrated high specificity (90.5%) for predicting postoperative complications using the receiver operating characteristics curves. Preoperative and postoperative (7 days) BNP levels were different depending on the abscence (mean BNP=$99{\pm}23\;pg/mL$ vs. $296{\pm}74\;pg/mL$, p<0.05) and presence (mean BNP=$212{\pm}29\;pg/mL$ vs. $408{\pm}23\;pg/mL$, p<0.01). Conclusion: Preoperative BNP levels >263 pg/mL predict postoperative complications in patients receiving CABG.

• Journal of Animal Science and Technology
• /
• v.46 no.4
• /
• pp.503-508
• /
• 2004

This study was conducted to estimate the growth curve parameters of crossbreds between Korean native boars and Landrace sows and their relationships with meat qualities. The data used were weight-age data and carcass data from 131 males and 122 females raised at N.L.R.I in Korea. Growth curve parameters were estimated from nonlinear regression using Gompertz model individually. Average mature weight(A), average maturing rate(k), and average inflection point(u) showing maximum growth rate estimated were 179.54${\pm}$6.06kg, 0.3154${\pm}$0.0059, and 5.50${\pm}$0.11 months in females, and 179.84${\pm}$6.33kg, 0.3049${\pm}$0.0061, and 5.24${\pm}$0.13 months in males, respectively. For the growth curve parameters and derived statistics, the phenotypic correlations of maturing rate with gain rate at inflection, mature weight, and inflection point were - .30, - .77, and - .93 in male, and - .31, - .78 and - .94 in female, respectively. Matrure weight was positively correlated to the inflection point as + .89 in both male and female, indicating that late maturing pigs with lower k had longer maturing period with increasing gain rate and reached point of inflection later than early maturing pigs with higher k, and grew to larger mature weight. Backfat thickness and erode fat contents were correlated with mature weight positively in male and negatively in female, and correlated with gain rate at inflection point positively in both male and female, of which coefficients were as high as .42 and .50 in male, respectively.

• Clinical and Experimental Pediatrics
• /
• v.48 no.12
• /
• pp.1362-1369
• /
• 2005

Purpose : This study aimed to investigate the correlation between the plasma level of N-terminal pro-B-type natriuretic peptide(pro-BNP) and several known risk factors influencing outcomes after Fontan operations, and to assess whether pro-BNP levels can be used as predictive risk factors in Fontan operations. Methods : Plasma pro-BNP concentrations were measured in 35 patients with complex cardiac anomalies before catheterization. Cardiac catheterization was performed in all subjects. Mean right atrium pressure, mean pulmonary artery pressure(PAP), and ventricular end-diastolic pressure(EDP) were obtained. Cardiac output and pulmonary vascular resistance were calculated by Fick method. Results : Plasma pro-BNP levels exhibited statistically significant positive correlations with mean PAP(r=0.70, P<0.001), pulmonary vascular resistance(r=0.57, P<0.001), RVEDP(r=0.63, P<0.001), LVEDP(r=0.74, P<0.001), and cardiothoracic ratio(r=0.71, P<0.001). The area under the ROC curve using pro-BNP level to differentiate risk groups in Fontan operations was high : 0.868(95 percent CI, 0.712-1.023, P<0.01). The cutoff value of pro-BNP concentrations for the detection of risk groups in Fontan operations was determined to be 332.4 pg/mL(sensitivity 83.3 percent, specificity 82.7 percent). Conclusion : These data suggest that plasma pro-BNP levels may be used as a predictive risk factor in Fontan operations, and as a guide to determine the mode of therapy during follow-up after Fontan operations.

• Journal of Sensor Science and Technology
• /
• v.3 no.2
• /
• pp.11-15
• /
• 1994

The TSEE characteristics of LiF(Mg,Cu,Na,Si)phosphor for gamma and beta rays are described. The TSEE glow curve of this phosphor showed 5 peaks in the range from $20^{\circ}C$ to $400^{\circ}C$ and its main peak appeared at $240^{\circ}C$. The sensitivity of the phospor for $^{60}Co$ gamma rays was about 450counts/mR. TSEE energy dependence for various beta radiation was nearly constant (${\pm}10%$) in the mean beta particle energy range from 0.02MeV to 0.8MeV. The efficiency of TSEE of the phosphor for beta radiation was $(2{\sim}15){\times}10^{-3}$.

• Korean Journal of Ichthyology
• /
• v.23 no.1
• /
• pp.30-36
• /
• 2011

Age and growth of shotted halibut Eopsetta grigorjewi were estimated using right sagittal otoliths of 389 fish specimens from February 2004 to January 2005 in the East China Sea. Examination of outer margins of the otolith showed that the opaque zone was formed once a year and annual rings were formed from December to March. The age of specimens examined ranged from 3 to 5 years. Shotted halibut begin spawning in February and show a peak in March. Length and weight relationships showed no significant difference between females and males (P>0.05), and can be expressed as TW=$0.5091{\times}10^{-2}TL^{3,222}(r^2=0.92)$. Estimated von Bertalanffy growth curve was $L_t=46.58(1-e^{-0.14(1+1.32)})$.

• Biomolecules & Therapeutics
• /
• v.6 no.4
• /
• pp.423-428
• /
• 1998

Aceclofenac is an orally effective non-steroidal anti-inflammatory agent of the phenylacetic acid derivative. Bioequivalence study of two aceclofenac preparations, the test drug (Senafe $n_{R}$: Daewon Phar-maceutical Company) and the reference drug (Airta $l_{R}$: Daewoong Pharmaceutical Company), was conducted according to the guidelines of Korea Food and Drug Administration (KFDA). Sixteen healthy male volunteers, 24$\pm$4 years old and 63.9$\pm$6.9 kg of body weight in average, were divided randomly into two groups and administered the drug orally at the dose of 100 mg as aceclofenac in a 2$\times$2 crossover study. Plasma concentrations of aceclofenac were monitored by HPLC method for 12 hr after administration. AU $Co_{-12h}$ (area under the plasma concentration-time curve from initial to 12 hr) was calculated by the linear trapezoidal method. $C_{max}$ (maximum plasma drug concentration) and $T_{max}$ (time to reach $C_{msx}$) were compiled directly from the plasma drug concentration-time data. Student's t-test indicated no significant differences between the formulations in these parameters. Analysis of variance (ANOVA) revealed that there are no differences in AU $Co_{12h}$, $C_{max}$ and $T_{max}$ between the formulations. The apparent differences between the formulations were far less than 20% (e.g., 0.25, 0.01 and 7.32 for AU $Co_{-12h}$, $C_{max}$. and $T_{max}$, respectively). Minimum detectable differences (%) between the formulations at $\alpha$=0.05 and 1-$\beta$=0.8 were less than 20% (e.g., 14.65, 12.47 and 15.46 for AU $Co_{-l2h}$, $C_{max}$ and $T_{max}$, respectively). The 90% confidence intervals for these parameters were also within $\pm$ 20% (e.g.,-10.19~10.68, -8.87~8.89 and -3.69~ 18.33 for AU $Co_{-12h}$, $C_{msx}$ and $T_{max}$, respectively). These results satisfy the bioequivalence criteria of KFDA guidelines, indicating that two formulations of aceclofenac are bioequivalent.quivalent.ivalent.ent.t.ent.

• Analytical Science and Technology
• /
• v.18 no.3
• /
• pp.224-231
• /
• 2005

In this study, the optimum conditions for the LPME (liquid phase microextraction) were investigated to overcome several shortcomings of traditional liquid-liquid extraction method. The LPME, which is automatic and dynamic, was used to analyze the five pesticides (dementon-S-methyl, diazinon, parathion, fenitrothion, EPN) extracted from vegetable, and HP 6890 GC/NPD was used as an analytic instrument. It was possible to optimize the extraction condition using the automatic LPME. The optimum extraction rate was obtained at pH 3.0 and $100{\mu}g/mL$ of salt concentration and standard curve showed linearity with over $R^2=0.9921$ in the range of $0.2{\sim}10{\mu}g/g$. The relative standard deviations were 7.7%, 9.8%, 7.8%, 9.7% and 8.2% in the $5.0{\mu}g/g$ concentration of dementon-S-methyl, diazinon, parathion, fenitrothion and EPN, respectively. The acquired accuracies were satisfactory showing 12.7%, 7.8%, 10.4%, -6.7% and -0.7% for dementon-S-methyl, diazinon, parathion, fenitrothion and EPN respectively.

• Magazine of the Korea Concrete Institute
• /
• v.9 no.2
• /
• pp.121-132
• /
• 1997

The thermal behavior of' concrete can be ch;lracterized from a knowledge of concrete ternperatu1.e at early ages, environmental conditions, and cement hydration in the mixture. 'l'o account for thost. interactions, a computer model was developed for prwlicting the temperature pr.ol'ile in hnrdcning c o n c r c t ~ st.r~icture in terms of material and tmvironmcntal factors. The cerncnt hydration cha~.acteristics such as the activating energy, total heat 1ihei.atr.d. anti th\ulcorner degree of' hydration. can represent the internal heat gc,neration. In this study. th(> activating c1ncrgy and the tlcgree of' hydration curve were determined well fmm the rnortn~. compressive strength tests while total amount of heat liberated was determined by tht> isothermal calorimctcr method. The main purpose of' this study is to correlate measured tt>mperaturr distributions in a concrete st1,ucture during thc hardening process with the ~ c s u l t s computed f'ro~n theoretical considrl.ations. Using twodimensional heat transfer model, first. the importance of several parameters will be identified by a parametric analysis. Then, the tcmpcmture distribution of thc cylindrical concrete specimen in the laboratory was mensuwti and compared with that yielded by thc theoretical considel.ations.