• 콘크리트학회지
• /
• 제28권5호
• /
• pp.84-87
• /
• 2016

• 콘크리트학회지
• /
• 제28권4호
• /
• pp.79-84
• /
• 2016

• 콘크리트학회지
• /
• 제7권5호
• /
• pp.51-57
• /
• 1995

• Nuclear Engineering and Technology
• /
• 제55권6호
• /
• pp.1988-1993
• /
• 2023

This experimental study investigated the effect of silica fume mixed in concrete blocks on laser-induced explosion behavior. We used a 5.3 kW fiber laser as a thermal source to induce explosive spalling on a concrete surface blended with and without silica fume. An analytical approach based on the difference in the removal rate and thermal behavior was used to determine the effect of silica fume on laser-induced explosive spalling. A scanner was employed to calculate the laser-scabbled volume of the concrete surface to derive the removal rate. The removal rate of the concrete mixed with silica fume was higher than that of without silica fume. Thermal images acquired during scabbling were used to qualitatively analyze the thermal response of laser-induced explosive spalling on the concrete surface. At the early stage of laser heating, an uneven spatial distribution of surface temperature appeared on the concrete blended with silica fume because of frequent explosive spalling within a small area. By contrast, the spalling frequency was relatively lower in laser-heated concrete without silica fume. Furthermore, we observed that a larger area was removed via a single explosive spalling event owing to its high porosity.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 2002년도 가을 학술발표회 논문집
• /
• pp.105-110
• /
• 2002

This paper proposes an analytical method to predict the behavior of reinforced concrete beams subjected to reversed cyclic loading. The proposed method is based on the compatibility aided truss model and adopts the stress vs. strain curve of concrete which considers the softening effects. This model Is verified by comparing to the six reinforced concrete panel tests.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 가을 학술발표회 논문집
• /
• pp.459-465
• /
• 1996

This paper is about unstable behavior in concrete during the localized deformation and the crack growths in concrete. By modeling the strain localization phenomenon of concrete, the stability condition of the localization is obtained and analyzed. And the stability and bifurcation condition of crack growths in two parallel cracks under different loading conditions are derived and discussed.

• Nuclear Engineering and Technology
• /
• 제46권1호
• /
• pp.73-80
• /
• 2014

A concrete cask is an option for spent nuclear fuel interim storage. A concrete cask usually consists of a metallic canister which confines the spent nuclear fuel assemblies and a concrete overpack. When the overpack undergoes a missile impact, which might be caused by a tornado or an aircraft crash, it should sustain an acceptable level of structural integrity so that its radiation shielding capability and the retrievability of the canister are maintained. A missile impact against a concrete overpack produces two damage modes, local damage and global damage. In conventional approaches [1], those two damage modes are decoupled and evaluated separately. The local damage of concrete is usually evaluated by empirical formulas, while the global damage is evaluated by finite element analysis. However, this decoupled approach may lead to a very conservative estimation of both damages. In this research, finite element analysis with material failure models and element erosion is applied to the evaluation of local and global damage of concrete overpacks under high speed missile impacts. Two types of concrete overpacks with different configurations are considered. The numerical simulation results are compared with test results, and it is shown that the finite element analysis predicts both local and global damage qualitatively well, but the quantitative accuracy of the results are highly dependent on the fine-tuning of material and failure parameters.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1996년도 봄 학술발표회 논문집
• /
• pp.52-56
• /
• 1996

In this study, when natural mineral with Silica components(Zeolite & Mudstone) abundant in Korea used as an admixture for concrete, it is investigated that the properties of strength increase and economic effect compared with Silica Fume, the general admixture of high strength concrete.

• 한국안전학회지
• /
• 제30권6호
• /
• pp.70-77
• /
• 2015

In this study, the governing design factors of GFRP-reinforced concrete bridge deck are analyzed for typical bridges in Korea. The adopted bridge deck is a cast-in-situ concrete bridge deck for the prestressed concrete girder bridge with dimensions of 240 mm thickness and 2.75 m span length from center-to-center of supporting girders. The selected design variables are the diameters of GFRP rebar, spacings of GFRP rebars and concrete cover thicknesses, Considering the absence of the specification relating GFRP rebar in Korea, AASHTO specification is used to design the GFRP-reinforced concrete bridge deck. The GFRP-reinforced concrete bridge deck is proved to be governed by the criteria about serviceability, especially maximum crack width, while steel reinforced concrete bridge deck is governed by the criteria on ultimate limit state. In addition, GFRP rebars with diameter of 16 mm ~ 19 mm should be used for the main transverse direction of decks to assure appropriate rebar spacings.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1989년도 가을 학술발표회 논문집
• /
• pp.35-38
• /
• 1989

The purpose of this report is to investigate and analyze development and achievement of flowing and high-strength concrete by reacy mixed concrete companies in Korea. For this purpose, the investigation was divided into three parts, i.e., superplasticizers, flowing concrete, high-strength concrete. And, they were asked to quality control manager in ready mixed concrete companies. Many researches have been carried out. And, flowing concrete is applied to field in a few case. In order to improve practical applicability of high-strength concrete and make concrete strength higher, to begin with, profound research for concrete ingredients will be needed along with presentation of methods for obtaining workability and quality assurance.