• Fibers and Polymers
• /
• v.4 no.4
• /
• pp.151-155
• /
• 2003

The abrasion behavior of three kinds of warp knitted fabrics, which are normally used for upper sole of footwear, was evaluated. We measured the changes of mechanical and structural properties of each sample as abrasion cycle increased. Each sample showed similar trends in compression and surface properties but there were significant differences in abrasion rate among the samples. The mechanical properties showed remarkable differences with directions. The frictional coefficient (MIU) of fabric surface increased at the beginning of abrasion and decreased as abrasion cycles increased. The weight and thickness of the fabric linearly decreased with abrasion cycles. The surface roughness (SMD) and the compressional resilience (RC) decreased as abrasion cycles increased while compressional energy (WC) increased.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.10a
• /
• pp.198-202
• /
• 2004

An analytical model using expanded bridging model was proposed to predict the elastic properties and behaviors of stitched multi-axial warp knitted (MWK) fabric composites, The characteristics of MWK fabric composites are the assemblage of multi-layers of fiber bundles for in-plane reinforcement and stitch yams for the through-the-thickness reinforcement. In the analysis, a representative volume of the MWK fabric composite was identified, The geometric limitations, effects of stitching yams and design parameters of MWK fabric composites were considered in the model. Then, the elastic properties and behaviors of MWK fabric composites were predicted, Finally, the results of proposed model of the composites were verified through the experiments, The predicted results were in fair agreement with the experimental results

• Journal of the Korean Society of Clothing and Textiles
• /
• v.29 no.9_10 s.146
• /
• pp.1274-1284
• /
• 2005

Effect of fixation methods and relaxation treatment on the dimensional stability and physical properties of MDPPA/HMM treated cotton knitted fabrics were studied. Combination of four different fixation methods - relaxation, swelling agent treatment, pad dry cure fixation, and wet fixation - were applied to flame retardant finish of 4 kinds of cotton knitted fabric with MDPPA/HMM. Then these fabrics were washed 10 times. As a result, In swelling treatment on 10G showed relatively higher value of length shrinkage than 14G. Length and width shrinkage were increased by initial washing treatment and no further change was shown after 6 washing cycles. After 10 washing cycles, length and width shrinkage decreased. The KES standardized basic value of B/W, 2HB/W and bursting strength of interlock were relatively larger than those of single jersey. The values of B/W and 2HB/W of cotton knitted fabrics were increased by relaxation and washing treatment but were decreased by swelling treatment. In addition, the bursting strength of the cotton knitted fabrics was decreased after fusing, washing and relaxation treatment.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.45 no.3
• /
• pp.453-463
• /
• 2021

The lengthwise and widthwise deformation of warp-knitted fabrics with different sizes and loading modes were evaluated. Moreover, five tricot samples cut in three directions were compared under four test conditions (A-D). In tests A and B, 500 and 250 g loads were applied on a layer of 20 × 20 and 5 × 10 cm² samples, respectively. In test C, a 20 × 20 cm² sample was folded in half over a rod, and 500 g load was applied to each half. In test D, a 20 × 20 cm² sample was sewn in a loop and subjected to a 500 g load. The lengthwise extension and widthwise contraction analysis results indicate that test B affords the largest values. However, analysis results of the warp-knitted fabric normalized through conversion to a 1 g load and 1 cm sample width indicate that the largest values are afforded for test D. Therefore, pattern reduction may vary depending on the measurement method and properties of the knitted fabric used for the compression wear production, causing variations in the finished product. Thus, an appropriate measurement method must be adopted based on the compression wear design and knitted fabric to be used.

• Journal of the Korean Society of Clothing and Textiles
• /
• v.37 no.5
• /
• pp.715-723
• /
• 2013

This develops a new and advanced S/S knitwear material made of linen/bamboo blended yarn. Linen/bamboo knitted fabrics were compared with linen/polyester knitted fabrics in terms of appearance as well as physical and comfort properties. Rib knitted fabrics were remarkably thicker than plain knitted fabrics. Knitted fabrics based on polyester yarns were heavier than those based on bamboo yarn. The porosity decreased in the following order: linen 100% > bamboo 100% > polyester 100%. The drape properties of bamboo 100% and linen/bamboo knitted fabrics were excellent. The pilling resistances of linen 100% and linen/bamboo knitted fabrics were excellent. The highest and lowest air permeability was observed in the case of linen/bamboo knitted fabrics and polyester 100% knitted fabrics, respectively. The instant cool-feeling was enhanced as the bamboo yarns were blended. The thermal conductivity of linen 100% knitted fabrics was the highest and the thermal conductivity of linen/bamboo knitted fabrics was higher than linen/polyester knitted fabrics. Bamboo 100% knitted fabrics showed a higher moisture regain than polyester 100% knitted fabrics. The results confirmed the superior appearance and comfort of a novel S/S knit wear material made of linen/bamboo knitted fabric.

• Journal of the Korean Home Economics Association
• /
• v.26 no.4
• /
• pp.1-13
• /
• 1988

The purpose of this study is to investigate water and after vapor transport characteristics of underwear fabrics. Experimental materials were cotton woven fabric and cotton knitted fabric, nylon tricot (untreated and hydrophilic finished) and cotton/polyester/cotton triple layer. Cotton knitted fabric have three types of knit structure (interlock, rib, plain stitch) and knit with either 38's or 60's combed yarn. And cotton woven fabric have plain weave with 60's combed yarn. As experimental methods, vapor cup test, dynamic method, vertical wicking test and transplanar uptake test were used. The results are as follows. 1) In cotton specimens, the order of water vapor transpiration (wvt) was plain > rib > interlock in the same yarn diameter. The knit fabric of thinner yarn showed the better wvt among the same knit structure. 2) In cotton specimens, the order of water absorbency was interlock > rib > plain in the same yarn diameter. the knit fabric of thicker yarn showed the better absorbency among the same knit structure. 3) When knit fabric (60's plain) is compared with woven fabric 960's plain), knit fabric showed faster rate of wvt, more amount of uptake and slower rate of water uptake than woven fabric did. 4) When compared untreated nylon with hydrophilic finished nylon, hydrophilic finished nylon showed much more water absorbency than untreated nylon did, but showed same rate of wvt. 5) The water transport characteristics of triple layer underwear fabric showed that the thinner and the lighter one, the better wvt and absorbency did.

• Proceedings of the Korean Fiber Society Conference
• /
• 2003.04a
• /
• pp.259-262
• /
• 2003

Fabric hand is ultimately a subjective response to physical stimuli, but there are clearly practical advantage in the development and commercial trading of textile fabrics to be gained from the replacement of the traditional subjective tactile assessment by an objective measurement evaluation method. Moreover, the reliable objective measurement method for warp knitted fabrics have not developed yet, despite their increasing importance. (omitted)

• Fibers and Polymers
• /
• v.6 no.1
• /
• pp.89-94
• /
• 2005

The purpose of this study is to offer acoustical database of warp knitted fabrics by investigating frictional sound properties and physiological responses according to structural parameters such as construction, lap form, and direction of mutual guide bar movement. Fabric sounds of seven warp knitted fabrics are recorded, and Zwicker's psychoacoustic param­eters - loudness(Z), sharpness(Z), roughness(Z), and fluctuation strength(Z) - are calculated. Also, physiological responses evoked by frictional sounds of warp knitted fabrics are measured such as electroencephalogram (EEG), the ratio of high fre­quency to low frequency (HF/LF), respiration rate (RESP), skin conductance level (SCL), and photoplethysmograph (PPG). In case of constructions, frictional sound of sharkskin having higher loudness(Z) and fluctuation strength(Z) increases RESP. By lap form, open lap has louder and larger fluctuating sound than closed lap, but there aren't significant difference of physi­ological responses between open lap and closed lap. In direction of mutual guide bar movement, parallel direction evokes bigger changes of beta wave than counter direction because of its loud, rough, and fluctuating sound. Fluctuation strength(Z) and roughness(Z) are defined as important factors for predicting physiological responses in construction and mutual guide bar movement, respectively.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2005.11a
• /
• pp.107-110
• /
• 2005

In this study we investigated the shear and forming behavior of chain stitched multi-axial warp knitted fabric preform, so called non-crimp fabric (NCF). The picture frame test was performed to characterize the shear behavior of NCF and also provide material properties for the numerical simulation of its deformation behavior. The forming behavior of NCF with chain stitch were investigated using hemispherical forming tools. The experimental results show that processing conditions such as blank holder force (BHF) and preform shape are crucial to determining the forming behavior of NCF. For instance, an asymmetric formed shape, which is due to the stitches introduced to NCF, turns into a symmetric one as BHF increases. Furthermore the in-plane and out-of buckling (wrinkle), the severance of which were quantified using image processing method, decreases significantly as BHF increases.

• Journal of Dental Rehabilitation and Applied Science
• /
• v.18 no.3
• /
• pp.145-155
• /
• 2002

The results of the present feasibility study are summarized as follows, 1. The three unit bridge of knitted material and UD fibre reinforcement has both the rigidity and the strength against a vertical occlusal load of 75N. 2. Stress concentration at the junctional area between the bridge and the abutments, i.e. between the pontic and the knitted caps was observed. In the case of the bridge with reinforcement straps, it was partly shown that the concentration problem could be improved by simply increasing the fillet size at the area. Further refining in the surface of the junctional area will be needed to ensure a further improvement in the stress distribution. This will require some trade off in the level of the stress and the available space. A parametric study will help to decide the appropriate size of the fillet. 3. Design refinement is a must to improve the stress distribution and realize the most favourable shape in terms of fabrication. The current straight bar with a constant cross section area can be redesigned to a tapered shape. The curve from the dental arch should also be placed on the pontic design. In accordance with design refinement, the resistance of the bridge frame to other load cases should be evaluated. 4. Although not included in the present feasibility study, it is estimated that bridges of the anterior teeth can be made strong enough with the knitted material without further reinforcement using unidirectional materials. In this regard, a feasibility study on design concepts and stress analysis for 3, 4, 5 unit bridge is suggested. 5. Two types of bridge were analysed in terms of fatigue. The safe life design concept, i.e. fatigue design concept, looks reasonable for the bridge where if cracks should form and propagate there is virtually nothing a dentist to do. The bridge must be designed so that no crack will be initiated during the life span. In the case of crowns, however, if constructed with composite resin with knitted materials, it might be possible to repair them, which in general is impossible for crowns of PFM or of metal. Therefore for composite resin crowns, a damage tolerance design concept can be applied and reasonably higher operational stresses can be allowed. In this case, of course, a periodic inspection program should be established in parallel. 6. Parts of future works in terms of structural viewpoint which need to be addressed are summarized as the following: 1) To develop processing technology to accommodate design concepts; 2) More realistic modelling of the bridge and analysis-geometry and loading condition. Thickness variation in the knitted material, taper in the pontic, design for anterior tooth bridge, the effect of combined loads, etc, will need to be included; 3) To develop appropriate design concepts and design goals for the fibre composite FPD aiming at taking the best advantage of knitted materials, including the damage tolerance design concept; 4) To develop testing method and perform test such as static ultimate load test, fatigue test, repair test, etc, as necessary.