• Journal of the Korean Wood Science and Technology
• /
• v.36 no.5
• /
• pp.49-55
• /
• 2008

This study was carried to investigate the effects of steaming and four different drying methods on the longitudinal liquid permeability of Korean pine (Pinus koraiensis Sieb.et Zucc.) board. Four drying methods were air drying, conventional kiln drying, microwave-vacuum drying and high temperature drying. Darcy equation was used for calculating the specific permeability of the small sapwood specimens taken from the treated boards while capillary rising method was used for the heartwood specimens. The sapwood specimens were extracted with water and benzene-alcohol solution to examine the mechanism of liquid flow in treated wood. No significant correlation was found between specific permeability and the number of resin canals of the sapwood specimens. Extraction decreased the differences of specific permeabilities of the sapwood specimens between the five treatment methods. The effects of extraction on the longitudinal permeability are different between five treatments. The fluid path in heartwood was observed by dynamic observation method.

• Applied Chemistry for Engineering
• /
• v.18 no.6
• /
• pp.575-579
• /
• 2007

Sludge disposal technology has been studied with many researchers since disposal of sewage sludge has been a social problem. The current technologies include incineration, carbonization, pyrolysis, landfilling and fertilization. However, all of these processes require a dry process, because sewage sludge with more than 80% high water content is difficult to be used as a raw material. This study has the purpose to establish the optimal operation conditions and the technology as changing the variables: kiln residence time, sludge load, dryer temperature, by using the previous study that is rotary kiln type dryer designed as a numerical simulation study. As the results, optimum conditions are determined as follows: kiln residence time, sludge load, dryer temperature are $62.5kg/m^3{\cdot}hr$, 26.2 min, $330^{\circ}C$, respectively. Content of water, drying efficiency, weight loss, volume loss show that the results are $10{\pm}2$, 88, 80, 60%, and the dried sludge is released by a dryer below 10 mm.

• Journal of the Korean Wood Science and Technology
• /
• v.13 no.2
• /
• pp.3-13
• /
• 1985

This study was carried out to investigate the effects of presteaming on the drying rate and drying defects of 3 cm - thick Quercus acutissima. Specimens for presteaming were steamed green at $100^{\circ}C$ for 4 hours and then kiln-dried to 10 percent moisture, content with controls, using the kiln-drying schedule ($T_4-C_2$) recommended by Rasmussen. The results obtained were as follows: 1. Presteaming reduced drying time approximately 18 percent from 70 to 10 percent moisture content. 2. The effect of presteaming on surface checking was not significant. 3. Presteamed specimens showed the reduction in end checking compared with controls. 4. Percents of boards with collapse, cupping, and honeycomb of presteamed specimens were slightly lower than those of controls. 5. Dry lumber grade of presteamed specimens was better than that of controls. Percent of first grade boards of presteamed specimens was 20 percent higher than that of controls and percents of second and third grade boards of presteamed specimens were 15 and 5 percent lower than those of controls, respectively.

• Journal of the Korean Wood Science and Technology
• /
• v.25 no.2
• /
• pp.67-74
• /
• 1997

A relationship between drying resistance and moisture content was found for 24, 27 and 30mm thick boards, and 45, 51 and 57mm thick dimensions of Japanese larch. Dahurian larch and radiata pine in order to modify the kiln schedule by using time schedules. The amount of drying resistance for Dahurian larch lumber was the highest, and radiata pine lumber was the lowest, on the basis of the same moisture content range. Drying resistance increased curvilinearly as moisture content decreased, and was higher for thicker lumber than for thinner lumber, at a given moisture content. Combined drying resistance for the three board thicknesses and the three dimension thicknesses showed a comparatively strong for radiata pine and a Japanese larch, while a weak correlation for Dahurian larch as a function of two independent variables, thickness and moisture content of lumber, respectively.

• Journal of the Korea Furniture Society
• /
• v.27 no.1
• /
• pp.43-48
• /
• 2016

PEG (Polyethylene glycol) impregnation in wood reduces the occurrence of checking during kiln drying. The volumetric shrinkages of wood PEG impregnated by pressure (PEG-P) or soaking (PEG-S) methods, and oven-dried by vent (VD) or air-tight (AD) methods were measured and compared with the controls. The average oven-dry weight of PEG impregnated specimens was larger than that of the controls by 3.6 g, but was not influenced by the drying methods. The average of the total volumetric shrinkage of PEG-P-VD specimens was the least (2.3%), while that of CON-S-AD specimens was the largest (28.9%). Within a drying method the total volumetric shrinkage of the control was the largest followed by PEG-S and PEG-P specimens, which implied that residual PEG in wood restrained its shrinkage during drying.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2005.05b
• /
• pp.253-256
• /
• 2005

This paper is to investigate the mixture proportion, compressive strength and drying. shrinkage of concrete depending on mineral admixtures such as fly ash (FA), blast furnace slag (BS) and cement kiln dust (CKD) under various contents of admixtures. The use of CKD had little effect on strength development at 3 days, while the use of FA and BS lead to similar compressive strength compared with that of control concrete. Concrete with CKD exhibited a reduction of compressive strength at 91 days, meanwhile concrete with FA and BS had a increase compared with that of control concrete. Drying shrinkage of concrete depending on CKD and BS increase compared with that of control concrete about $10\∼20\%$, while the use of FA exhibited reduce compared with that of control concrete about $10\∼15\%$.

• Journal of the Korean Wood Science and Technology
• /
• v.51 no.6
• /
• pp.447-447
• /
• 2023

This study aimed to convert underutilized moso bamboo into high-value added products such as fences, interior materials, lighting fixtures, and accessories. Green moso bamboo poles with a diameter of approximately 10 cm and a length of approximately 3.7 m were heat treated at 140℃ using a large-scale kiln. The processing time was meticulously adjusted through various stages, including pretreatment (6-8 hours at 60℃), cooking (8-10 hours at 100℃), steaming (26-30 hours at 120℃), heating (4-6 hours at 140℃), and finally, cooling (below 80℃). A meticulously designed heat treatment process has enabled efficient mass production of moso bamboo poles with improved qualities, including minimal splitting, moisture levels below 3%, and a specific gravity of 1.05. The focus of this study was to present the physical and drying properties, such as color, dimensional change, specific gravity, moisture content, and splitting, observed during the heat treatment process.

• 한국연소학회:학술대회논문집
• /
• 2013.06a
• /
• pp.51-54
• /
• 2013

Rotary kiln reactors are frequently equipped with an axial burner with which solid burden material is directly heated. Lifters are commonly used along the length of the system to lift particulate solids and increase the heat transfer between the solid bed and the combustion gas. The material cascading from the lifters undergoes drying and reacting through direct contact with the gas stream. In this study, volume distribution of materials held within lifters was modeled according to the different lifter configuration and appropriate configuration was used for the design purpose. This was applied to the one-dimensional heat balance model of a counter-current flow reactor, which contributes to the increase of the effective contact surface, and thereby enhances the heat transfer.

• Journal of the Korean Wood Science and Technology
• /
• v.14 no.4
• /
• pp.29-39
• /
• 1986

To investigate the effect of presurfacing, both 25mm rough and pre surfaced oak boards (Quercus grosseserrata BI.) were dried in the same dry kiln condition. Drying curves, drying strains and drying defects of rough and presurfaced boards were compared. The results obatained are as follows. 1. Average drying rate of rough and presurfaced boards from green to 10% M.C. was 0.276%/hr. and 0.284%/hr., respectively. 2. At the early stage of drying, in case of rough boards, maximum tensile strain of outer slices was $-24.2{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $13.0{\times}10^{-4}$mm/mm, and in case of pre surfaced boards, maximum tensile strain of outer slices was $-14.5{\times}10^{-4}$mm/mm and maximum compressive strain of innermost slices was $28.1{\times}10^{-4}$mm/mm. And in both cases, stress reversal occurred at about 40% M.C.. 3. Maximum surface checking appeared at about 40% M.C.. Of the 10 rough boards. 6 hoards contained surface checks, but presurfaced boards did not contained surface checks after drying. And the results of end checking were similar to those of surface checking. But, honeycomb was not found in both cases. 4. Board shrinkage. warp and casehardening of presurfaced boards were similar to those of rough boards. But, collapse of prsurfaced boards was less than that of rough boards.

• Journal of the Korean Wood Science and Technology
• /
• v.2 no.2
• /
• pp.5-7
• /
• 1974

1. This study indicates that above the fiber saturation point the drying rate can be increased with increasing the velocity of the air circutation, i.e., the drying rate of sample boards is proportional to the air velocity, but below the fiber saturation point, the effect of the velocity of air circulation is very low as shown in Figs. 1 and 2. 2. Under the controlled temperature and humidity in the kiln, the more the sample boards have moisture, the higher drying rate of it can be obtained. In other words, this means that even though in the case of drying various moisture content of wood, at the final drying stage, approximately the same percentage of moisture content of wood can be secured by employing the higher velocity of air circulation. 3. This study shows that the rate of drying in kiln changes distinctly at the fiber saturation point, i, e., above the fiber saturation point, the drying curve shows concave aginst the X axsis, but below the fiber saturation point, in the range from 30 percent of moisture content to 20 percent of moisture content, the curve shows convex as shown in Fig. 3. As the drying progresses, however, the drying curve shows concave again below 20 percent of moisture content. This means that inflection point of drying curve may be located clearly at the fiber saturation point, i.e., 30 percent of moisture content. As mentioned above, the 30 percent of moisture content of wood at which the inflectional point appears can be recognized as a critical point, i. e., the fiber saturation point at which all free water was removed from wood. The existence of inflectional point indicates that the evaporation of hygroscopic water in a cell wall is more difficult than the evaporation of free water in a cell cavity and the minor space of cell wall. The convex curve in the range of moisture content from 30 percent to 20 percent means that the evaporation of capillary condensed water has a tendency of the same rates of drying approximately, but as approaching to the 20 percent of moisture, the transfusion of moisture from wood becomes difficult because of having less moisture in cell wall. Below 20 percent of moisture content, the drying curve shows concave again, which means that it is difficult to remove the moisture located nearer to the surface of cellulose molecules and the surface bound water. These relations were revealed in Fig. 4. In comparison AC curve which does not have the two inflection points with BD curve which has two inflection points, i.e., Band D, they are mentioned already, by existence of the inflection points, the curve BD shows that the change of drying rate in the interval from 20 percent of moisture content to 30 percent of moisture content is not greater than in the case of the curve AC in the same interval. At the inflection point of 30 percent of moisture content, it can be noticed that the changing of the drying rate is very conspicuous. This phenomenon also can be recognized, as it is noticed by the Fig. 3, the drying rate from green to 30 percent of moisture content is very great. But the inclination of the curve is very slow from 30 percent of moisture content to 20 percent of moisture content, i.e., the inclination of the curve becomes almost horizontal lines. Acknowledgments Gratitude is expressed to Fred E. Dickinson, Professor of 'Wood Technology, School of Natural Resources, University of Michigan, USA for his suggestion to carry out this study.