• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.49 no.6
• /
• pp.105-110
• /
• 2012

In this paper, A planar UWB antenna with notched WLAN band, 802.11a band (5.15 ~ 5.825GHz), by using slot and slit is designed by using CST Microwave Studio. The notched bandwidth can be controlled by the length and width of the slot and slit in the patch and ground plane and it's radiation characteristics are examined through the experiments. The bandwidth based on the -10dB return loss level can be covered the full UWB band (3.1 ~ 10.6GHz) with a notched WLAN band (5.147 ~ 5.83GHz). Also, the experimental radiation pattern is almost omnidirectional in the H-plane.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.5
• /
• pp.426-429
• /
• 2017

For the W-band remote sensing radiometer, direct detection type radiometer receiver is designed. The receiver should be low noise and high gain of 60 dB unlike communication and radar receiver. The W-band radiometer consist of 4-stage low noise, high gain amplifier, band pass filter and square law detector. The developed direct detection receiver show 4 GHz bandwidth, 56 dB gain, and 4,500 mV/mW voltage sensitivity at integrator output port for -20 dBm input power at 94 GHz.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.219-222
• /
• 2003

In this paper, we designed a Ku-band BPF(Band Pass Filter) by microstrip line that most usually used a microwave device design and fabrication. Here a substrate of designed BPF were silicon substrate(${\varepsilon}_r=11.8$), and metal line was copper and silver/copper structure. And a configration of BPF was used hairpin pattern. A center frequency of designed BPF was 10GHz and their FBW(Fractional Band Width) was 20%(2GHz). It presented simulated results obtained for a 10GHz filter which yields an insertion loss of 0.1dB that ripple value related chebyshev reponse. Finallt we tried to make that a 30dB attenuation frequency was 20% of center frequency.

• Journal of the Society of Naval Architects of Korea
• /
• v.49 no.4
• /
• pp.359-366
• /
• 2012

This is the final one of the two companion papers dealing with accuracy of accumulated fatigue damage estimation under wide band process. It is stated that four kinds of wide band models exist: typed of equivalent stress, combined PDF, correction factor, and damage combination. For the idealized ESDs from full scale measurement data on an 8100TEU container vessel, fatigue damages are compared for a narrow band prediction model based on Rayleigh PDF and five wide band fatigue prediction models of Dirlik, Wirsching-Light, Jiao-Moan, Benasciutti and DNV. DNV model consistently overestimates fatigue damages regardless of variation of ESDs. Predictions by Jiao-Moan model, which is understood as standard method for design of offshore platforms, are also in conservative side. Best accuracy is found from the results by Dirlik and Benasciutti models, but Benasciutti model is preferred since it can easily combined with narrow band fatigue damage based on Rayleigh PDF.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07b
• /
• pp.574-577
• /
• 2004

A coupler is a microwave passive component used for power coupling or dividing. Regarding the trend of current telecommunication systems it is highly desirable for monolithic integration of passive components as such LTCC(Low temperature cofired ceramics) technology offers potential advantage in size, cost and performance. Utilizing LTCC technology a 2012 size type dual band coupler for DCS and EGSM band was fabricated. Its characteristics such as coupling, insertion loss, isolation and directivity was measured and compared with simulation results

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39A no.12
• /
• pp.718-728
• /
• 2014

The multi-band wireless local area network (WLAN) using 60 GHz band and the lower band (typically 2.4 GHz/5 GHz band) can support the very high data rate in short-distance communication using 60 GHz band and the long-distance communication using the lower band. For heightening the efficiency of multi-band WLAN, an band selection scheme is a necessity. In this paper, we propose an effective frequency band selection scheme for multi-band WLANs. By using computer simulation with NS-3, we show the performance of the proposed schemes when the stations suffer from the human blockage and the log-normal shadowing.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.9
• /
• pp.60-65
• /
• 2009

In this paper, we present a compact Ultra-Wideband band-pass later with notched band at fireless-LAN band using a band-pass and band-notch filter. The structure of our proposed band-pass filter is very simple, and the DGS(Defected Ground Structure) structure is used to get the low-pass filter characteristic, and an embedded open-stub structure is used to get the notched filter. Our proposed band-pass filter can be much smaller than a cascaded filter. As a result of measurement, the insertion loss is less than 0.7dB throughout the pass-band of $2.21GHz{\sim}10.92GHz$, the return loss is more than 17dB and the group delay maximum variation is 0.24ns and a notched band is at $5.3GHz{\sim}5.7GHz$.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.6
• /
• pp.1196-1200
• /
• 2009

This paper proposed a tunable band pass filter. It is two-poles direct capacitive coupled resonator band pass filter which the capacitors of parallel resonators are changed by varactor diodes. The DC bias controls to change the value of capacitance in the parallel resonator for tunning the pass band. To validate the proposed design method, we fabricated the band pass filter which has tunable center frequency from 200MHz to 245MHz.

• 한국ITS학회:학술대회논문집
• /
• 2004.11a
• /
• pp.323-327
• /
• 2004

• Proceedings of the KIEE Conference
• /
• 2008.10b
• /
• pp.217-218
• /
• 2008

Since the digital TV signal band is very wide ($54{\sim}806MHz$), the VCO used in the frequency synthesizer must also have a wide frequency tuning range. Multiple LC VCOs have been used to cover such wide frequency band. However, the chip area increases due to the increased number of integrated inductors. A general method for achieving both reduced VCO gain(Kvco) and wide frequency band is to use the switched-capacitor bank LC VCO. In this paper, a scheme is proposed to cover the full band using only one VCO. The RF VCO block designed using a 0.18um CMOS process consists of a wideband LC VCO with reduced variation of VCO gain and frequency steps. Buffers, divide-by-2 circuits and control logics the simulation results show that the designed circuit has a phase noise at 100kHz better than -106dBc/Hz throughout the signal band and consumes $9.5{\sim}13mA$ from a 1.8V supply.