• 대한조선학회논문집
• /
• 제33권3호
• /
• pp.1-7
• /
• 1996

용접이음부재에서 피로강도에 큰 영향을 미치는 용접부의 응력집중계수를 추정하였다. 여기서는 하중전달형 십자필렛용접이음부를 그 대상으로 하였다. 필렛용접이음부에서 토우파괴를 일으키는 피로균열발생부인 용접토우부의 응력집중계수를 구하기 위해 인장하중하에서 토우부의 적정 요소 크기를 검토하고 여러 파라메타들의 값을 변화시켜 유한요소 응력해석을 수행하였다. 즉 용접토우부의 형상인 토우각 및 곡률반경의 영향과 용입부족부 길이의 변화를 동시에 고려한 응력집중계수를 정량적으로 구하였다. 그리고 그 결과를 이용하여 응력집중계수 추정식을 유도하였다.

• 대한기계학회논문집A
• /
• 제22권4호
• /
• pp.905-915
• /
• 1998

Static tensile tests using adhesive-bonded single-lap joints of aluminum alloy were conducted to investigate the effect of geometric factor, overlap length, adherend thickness, adhesive thickness and material composition of adherend/adhesive on the strength of adhesive joint. The average applied shear stress at joint fracture decreased with increasing lap length. However increasing the adherend thickness resulted in a higher joint strength. Higher yield strength of adherend and lower elastic modulus of adhesive is advantageous to the adhesive joint. Newly proposed modified joint factor could be well evaluated the influence of lap length, adherend thickness and adhesive thickness on the bond strength for adhesive joints.

• 한국생산제조학회지
• /
• 제21권3호
• /
• pp.439-445
• /
• 2012

The stress singularity for the excess adhesive on interface of adhesively bonded joint was investigated by using the 2-dimensional elastic boundary element method (BEM). To establish a reasonable strength evaluation method and a fracture criterion for the excess adhesive of interface in adhesively bonded joint, it is necessary to evaluate fracture parameters with various bonding conditions. Under the variations of adhesively bonded thickness (h) and diameter (d) for the excess adhesive, a stress analysis was performed, and from the results, the stress singularity index (${\lambda}$) and the stress singularity factor (${\Gamma}$) were calculated. The variations have a great influences on the stress singularity for the excess adhesive of interface in adhesively bonded joint, and the ${\Gamma}$ is reduced as the "h" and "d" increase.

• 한국자동차공학회논문집
• /
• 제5권6호
• /
• pp.53-63
• /
• 1997

This study examines the influence of some dimensional errors on the shudder-type disturbance of the tripod joint and vehicle, using an experimental evaluation and related simulation. With the introduction of the concept of influence factor, the sensitivities of shudder-type disturbance can be evaluated as the ratio of the difference between the ideal value without dimensional errors and actual value with them in the tripod joint and vehicle. Futhermore, influence factors calculated in this study can be utilized as a basic design data for the practical application of the tripod joint to an automobile design.

• 한국지진공학회논문집
• /
• 제16권5호
• /
• pp.13-21
• /
• 2012

본 논문에서는 푸쉬오버해석을 통해 철근콘크리트 중간모멘트골조의 반응수정계수를 확인하기 위하여 5층 구조물을 KBC2009에 맞게 구조설계 하였다. 보 및 기둥 부재의 휨모멘트-곡률 관계는 화이버 모델로 확인하였으며 보-기둥 접합부 모멘트-회전각 관계는 Simple and Unified Joint Shear Behavior Model과 보-기둥 접합부 모멘트 평형관계를 이용하여 확인하였다. 푸쉬오버해석 결과 보-기둥 접합부 비탄성 전단거동을 무시하는 경우 구조물의 강도가 과대평가 되었다. 반응수정계수는 내진설계범주 C에 대하여 설계한 경우 평균 7.78, 내진설계범주 D에 대하여 설계한 경우 평균 3.64로 평가되었다.

• 한국항공우주학회지
• /
• 제41권3호
• /
• pp.194-200
• /
• 2013

복합재료 적층판 기계적 체결부 표준시험(ASTM D5961) 결과에 대하여 이론적 강도 계산 및 유한요소 해석결과를 비교한다. 응력집중계수를 산출하기 위하여 ASM Handbook의 금속 및 복합재료에 대한 산출식을 이용하여 실험 결과값과 비교한다. 형상학적 인자들과 체결방식(단일/이중 겹칩)에 따른 체결강도의 차이도 비교한다. 유한요소 해석에 있어, 복합재료 적층판의 기계적 체결부의 효율적인 유한요소 모델을 찾기 위해 몇 가지 유한요소 모델들과 실험 결과들을 비교한다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 1998년도 춘계학술대회 논문집
• /
• pp.298-303
• /
• 1998

Most of mechanical structures are combined of substructures such as beam and/or plates. There are few system with unibody structures but are not a few systems with united body structures. Generally the dynamic analysis of whole structures is perform ed under alternating load. However, the analysis of each joint area is more important than others for zero severity. This paper presents the results of analysis of concentration stress in bolt jointed structure with variable preload. At frist, a static vibration test was performed to find out a nominal stress of bolt joint ed plates from the relationship between natural frequency and nominal stress. Then a concentration stress was computed at contact point between bolt and plate in the structure. It is believed that the proposed method has promising implications for safer design with fatigue quality index of stress concentration factor and has merit for cost down and saving time at the beginning of vehicle development.

• 소음진동
• /
• 제9권1호
• /
• pp.174-183
• /
• 1999

An analytical model for the lateral vibration of beams with a bonded lap joint and partial layered dampers has been proposed in this paper. Both shear and normal forces acting along the interface between the elastic and viscoelastic layers were considered in the vibration analysis. Analytical results were compared with those obtained by a finite element method. Effects of the size and location of layers in partial dampers on system loss factor($\eta_s$) and resonant frequency($\omega_r$) were studied. which showed that partial dampers adhered to the site exhibiting the maximum amplitude of vibration were most influential in the increase of $\eta_s$ and the decrease of $\omega_r$. Specific system loss factor( $\eta_s$ divided by total mass of system) was also evaluated in the analysis.

• Journal of Welding and Joining
• /
• 제13권2호
• /
• pp.106-114
• /
• 1995

The characteristics of adhesive bonded joint of steels for automobile were investigated. Shear and tear strength were tested and analyzed for the joints of cold rolled steel sheets bonded with three kinds of epoxy and urethane based adhesive. The results showed that the tensile shear strength and the tear strength of adhesive joint were affected by the shape of adhesive joint such as the length and width of adhesive joint. The thickness of adhesive layer was very important factor affecting the bonding strength. The shear strength increased with decrease of the thickness of adhesive layer, while the tear strength decreased as the thickness of adhesive layer decreased. In comparison with the strength of spot welded joint, the shear strength of adhesive Joint was higher than that of spot welded joint, but the tear strength of adhesive Joint was lower than that of spot welded joint.

• 한국운동역학회지
• /
• 제28권4호
• /
• pp.199-205
• /
• 2018

Objective: The purpose of this study was to examine the effect of increase in barbell weight on closely related variable to the anterior cruciate ligament (ACL) injury which are knee joint kinematics, joint load, joint moment, and maximum load attainment point during snatch of the weight lifting. Method: The subjects of the study were 10 male Korean national weight lifting athletes (69 kg 5, 77 kg 5; age: $21.80{\pm}3.91yrs.$, height: $168.00{\pm}4.06cm$, weight: $75.00{\pm}4.02kg$, career: $7.8{\pm}3.99yrs.$, snatch records: $168{\pm}4.06kg$). The weight of the barbell during the snatch operation was set at 70%, 75% and 80% of the highest records for each subject studied. Results: The result obtained from the one-way repeated measure ANOVA are as follows: With increased barbell weight, the extension moment of the left knee joint was higher in the 80% condition than the 70% (p<.001). However, other variables were not statistically significant difference. According to the factor analysis of the variables related to maximum load attainment point of the ACL major injury variables, the first sub-factor was the internal shear force, the posterior shear force, the abduction moment, and the muscle activity of the VL. The second sub-factor was the extension moment of the knee joint, compressive force, adduction moment, and the third sub-factor was the muscle activity of BF. Conclusion: These results indicate that the possibility of ACL injury can be lowered when performing a stable snatch movement.