• Polymer(Korea)
• /
• v.25 no.3
• /
• pp.359-366
• /
• 2001

Isothermal physical aging of a glass fiber/epoxy composite was examined at different aging temperatures ($T_a$) and degrees of conversion (monitored by the glass transition temperature, $T_g$) by means of the TBA torsion pendulum technique. The range of aging temperature was from 10 to $130^{\circ}C$ : the conversion was systematically changed from $T_g$=$76^{\circ}C$ to $T_g$=$177^{\circ}C$ (fully crosslinked). The effect of isothermal physical aging was manifested as perturbations of the modulus and mechanical loss vs. temperature in the vicinity of $T_a$ for all conversions. The rate of isothermal physical aging determined from the change of modulus with aging time at fixed aging temperature decreased and then increased with increasing conversion below T$_{a}$=9$0^{\circ}C$. There exists a superposition in aging rate vs. ($T_g$ -$T_a$) by shifting horizontally and vertically. This implies that the physical aging process is independent of the change of chemical structure as conversion proceeds. It has been found that water absorbed at the aging temperature below $70^{\circ}C$ during isothermal physical aging lowers the apparent aging rate. It is due to the absorbed water molecules forming strong polar interactions with hydroxyl group on network chain and reducing the segmental mobility during the physical aging.g.

• Journal of the Korean Ceramic Society
• /
• v.27 no.8
• /
• pp.971-978
• /
• 1990

The ifluence of transformability and stabilized effects in tetragonal phase on the isothermal phase transformation of Y-TZP at low temperature were investigated. The transformability of Y-TZP powders were gradually increased with calcination temeprature and reached maximum at critical temperature, but when the Y-TZP powders were calcined above critical temperature, transformability of Y-TZP were gradually decreased with increasing calcination temperature. It was concluded that maximum transformability was appeared because particle size effects decreased and constrain effects increased with calcined temperature. The isothermal phase transformation during aging at 25$0^{\circ}C$ only observed in Y-TZP stabilized by constrain effects and the amounts of transformation during aging at 25$0^{\circ}C$ only observed in Y-TZP stabilized by constrain effects and the amount of transformed monoclinic phase during aging decreased with increasing constrain effects. From these results, the mechanism of isothermal phase transformation and degradation behaviors at low temperature in Y-TZP was concluded that occurred by decreasing of constrain effects due to stress relaxation at grian boundary.

• Journal of the Korean Magnetics Society
• /
• v.19 no.3
• /
• pp.100-105
• /
• 2009

The high-temperature isothermal aging is studied in ultra-supercritical steel, which is attractive to the next generation of power plants. The effects of microstructure on reversible permeability are discussed. Isothermal aging was observed to coarsen the tempered carbide ($Cr_{23}C_6$), generate the intermetallic ($Fe_2W$) phase and grow rapidly during aging. The dislocation density also decreases steeply within lath interior. The dynamic coercivity, measured from the peak position of the reversible permeability profile decreased drastically during the initial 500 h aging period, and was thereafter observed to decrease only slightly. The variation in dynamic coercivity is closely related to the decrease in the number of pinning sites, such as dislocations, fine precipitates and the martensite lath.

• Polymer(Korea)
• /
• v.36 no.4
• /
• pp.507-512
• /
• 2012

Thin (~650 nm) and ultrathin (~50 nm) films of neat PMMA and PMMA containing 5 wt% of methacryl-polyhedral oligomeric silsesquioxane were prepared in this work. The effects of film thickness and POSS on glass transition temperature ($T_g$) and isothermal physical aging were investigated by means of differential scanning calorimetry (DSC). $T_g$ depression was observed as film thickness was decreased and Ma-POSS molecules were incorporated. Enthalpy relaxation (${\Delta}H_{Relax}$) due to the isothermal physical aging was reduced by ultra-thin film thickness and the addition of Ma-POSS. KWW (Kohlrausch-Williams-Watts) equation was used to fit ${\Delta}H_{Relax}$ vs. aging time data providing the fitting parameters; maximum enthalpy recovery (${\Delta}H_{\infty}$), relaxation time (${\tau}$) and non-exponentiality parameter (${\beta}$).

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.225-228
• /
• 2011

Magnetic properties and Rockwell hardness of 1Cr-0.5Mo steel have been investigated as a function of isothermal aging time. Our results showed that coercivity, hysteresis loss and Rockwell hardness in the aged samples decreased as aging time increased. This phenomenon was analyzed using optical microscopy and scanning electron microscopy. A significant diffusion of Cr and Mo atoms formed $M_2C$ and $M_7C$ carbides, lowering the matrix strength. $M_2C$ and $M_7C$ carbides partially segregated inside grains, diffused into grain boundaries, and finally resulted in a soft ferrite matrix and a hard grain boundary. The magnetic and mechanical softening of the matrix is likely to govern the properties of the sample more than the hardening of the grain boundary by carbide precipitations.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.6
• /
• pp.287-293
• /
• 2021

This study was intended to investigate the influence of Al content on hardness and microstructural characteristics of discontinuous precipitates (DPs) formed by isothermal aging in Mg-8.7%Al and Mg-10%Al alloys. In order to obtain large amount of DPs in the microstructure, the alloy specimens were solution-treated at 688K for 24 h followed by water quenching, and then aged at 418K for 48h. The Mg-Al alloy with higher Al content was characterized by higher volume fraction of DPs at the same aging condition, lower interlamellar spacing of the DPs, thinner β phase layer and higher β phase content in the DPs. This is closely related to the higher velocity of discontinuous precipitation process resulting from the higher Al supersaturation in the α-(Mg) matrix. The Mg-10%Al alloy showed higher hardness of the DPs and greater difference in hardness between as-cast state and DPs than the Mg-8.7%Al alloy.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.277-284
• /
• 2023

Hardness and damping characteristics of fine discontinuous precipitates (DPs) microstructure generated by low temperature long term isothermal aging were investigated in comparison with those of T6 heat-treated microstructure composed of DPs and continuous precipitates (CPs) in Mg-9%Al alloy. In this study, T6 and fine DPs microstructures were obtained by isothermal aging at 453 K for 24 h and at 413 K for 336 h, respectively, after solution treatment at 693 K for 24 h. The DPs microstructure exhibited higher hardness than the T6 microstructure, which is related to the lower (α + β) interlamellar spacing of the DPs. The DPs microstructure possessed better damping capacity than the T6 microstructure in the strain-amplitude independent region, whereas in the strain-amplitude dependent region, the reverse behavior was observed. The damping tendencies depending on strain-amplitude were discussed based on the microstructural features of the T6 and DPs microstructures.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.172-178
• /
• 2017

Thermal property is one of the important characteristic in the field of energetic materials. As the energy material is released during decomposition, DSC(Differential Scanning Calorimetry) is frequently used for the thermal analysis. In case of the dynamic DSC measurements, thermal dynamic change like melting is prevented from the thermal property measurements. And due to the predicting kg scale, the conditions of the heat exchange with the environment significantly is changed. In this study, As the method to resolve the problem, we predict the thermal aging property using the AKTS thermokinetic program from DSC measurements which performed isothermal method. Predicting the thermal aging properties from ARC(Accelerating Rate Calorimetry) measurement, we compare two results.

• Journal of the Korean Society for Heat Treatment
• /
• v.33 no.4
• /
• pp.173-179
• /
• 2020

The purpose of this study was to investigate comparatively the microstructural characteristics and hardness of discontinuous precipitates (DPs) in Mg-9%Al alloy, which were formed by continuous cooling (CC) from 678 K to RT and isothermal aging (IA) at 413 K, respectively. In as-cast state, the Mg-9%Al alloy consisted of partially divorced eutectic β(Mg₁₇Al₁₂) particles with a small amount of DPs showing (α+β) lamellar morphology adjacent to the β particles. The DPs formed by CC had interlamellar spacings in a broad range of 0.85~2.12 ㎛ (1.51 ㎛ in average) owing to the various formation temperatures in response to continuous cooling process. Meanwhile, the DPs formed by IA had relatively narrower interlamellar spacings of 0.14~0.29 ㎛ (0.21 ㎛ in average), which is associated with the low and constant formation temperature. Thinner and higher volume fraction of β phase layers were noticeable in the DPs formed by IA. Higher hardness values were obtained in the DPs formed by IA than the DPs formed by CC, which may well be ascribed to the finer lamellar structure and higher β phase content of the DPs formed by IA.

• Journal of the Korean Ceramic Society
• /
• v.33 no.6
• /
• pp.637-644
• /
• 1996

Phase stability and isothermal phase transformation during gaging at 25$0^{\circ}C$ were investigated in yttria stabilized zirconia powders prepared from hydrolysis of zirconium isopropoxide. The stability of tetragonal phase at room temperature in zirconia powder was decreased with calcination temperature but increased with the addition of yttria content. During aging at 25$0^{\circ}C$ in humid atmosphere isothermal phase transformation occurred in tetragonal zirconia powder stabilized by constraint effect not by alloying effect and grain size effect. Many twins and microcrackings were found in transformed monomlinic zirconia particles.