• 한국주조공학회지
• /
• 제21권4호
• /
• pp.246-252
• /
• 2001

Variation in the microstructure of Mg-5%Al semi-solid slurry during isothermal heating was investigated in relation to initial microstructure, holding time, and holding temperature. Specimens with three different initial microstructures were isothermally heated. Dendritic structure in as-cast ingot was decomposed into solid globules in the semi-solid slurry during isothermal holding, while in the recrystallized specimens prepared by extrusion or rolling the size of solid particles was continuously increased during the heating. Effects of mold temperature and liquid fraction of slurry on the mold filling ability were also studied. Very thin section (0.4 mm) could be successfully filled up to 50 mm by 60% liquid slurry when the mold was heated to $600^{\circ}C$.

• 동력기계공학회지
• /
• 제14권5호
• /
• pp.71-75
• /
• 2010

Leak detection technology is a challenging research until nowadays, because it has wide and various applications in industry. Furthermore pneumatic component reliability test based on ISO requires air leakage measurement. The conventional measurement methods need a complex operation and the calibration of leak detector. Tracing the history of our study, we proposed a new method for measurement of leak flow rate using isothermal chamber. In this study, propose a simulation model of isothermal chamber by infinitesimal flow -rate, such as a leak flow-rate. The effectiveness of the proposed simulation model is proved by simulation and experimental results. Base on the comparison results, proposed simulation model is good agreement with experimental results.

• 대한기계학회논문집
• /
• 제17권12호
• /
• pp.2970-2981
• /
• 1993

In hot closed-die forging the load increases rapidly near the final stage. Preforming operation is important to both the sound final forging and die-service life. In this study, the material flows during preforming and final forging are investigated. The physical modeling with Plasticine as a model material showed clear flow patterns. The forging process were numerically simulated by the finite element method with the isothermal and the non-isothermal models. The flow patten of the isothermal simulation showed good agreements with the experiments. Temperature changes and pressure distributions on the die surfaces during one cycle of the forging process were obtained from the non-isothermal simulation. High pressure and temperature were developed at certain areas of the die surfaces. It was concluded that those areas usually coincide with each other and should be distributed by the preforming operations to enhance the die life.

• 한국표면공학회지
• /
• 제24권4호
• /
• pp.196-205
• /
• 1991

Multi-level thin films are very important in ULSI applications because of their high electromigration resistance. This study presents the effects of titanium, titanium nitride and titanium tungsten underlayers of the stability of multi-aluminum thin films during isothermal annealing. High purity Al(99.999%) films have been electron-beam evaporated on Ti, TiN, TiW films formed on SiO2/Si (P-type(100))-wafer substrates by RF-sputtering in Ar gas ambient. The hillock growth was increased with annealing temperatures. Growth of hillocks was observed during isothermal annealing of the thin films by scanning electron microscopy. The hillock growth was believed to appear due to the recrystallization process driven by stress relaxation during isothermal annealing. Thermomigration damage was also presented in thin films by grain boundary grooving processes. It is shown that underlayers of Al/TiN/SiO2, Al/TiW/SiO2 thin films are preferrable to Al/SiO2 thin film metallization.

• 한국마이크로전자및패키징학회:학술대회논문집
• /
• 한국마이크로전자및패키징학회 2002년도 춘계 기술심포지움 논문집
• /
• pp.152-157
• /
• 2002

The cure and rheological behavior of Diglycidyl ether of bisphenol F, catalyzed by four kinds of imidazoles and a Nadic methyl anhydride curing agent were studied using a differential scanning calorimeter (DSC) and rheometer. The isothermal traces were employed to analyze cure reaction. The DGEBF/anhydride conversion profiles showed autocatalyzed reaction characterized by maximum conversion rate at 20~40 % of the reaction. The rate constants obtained from isothermal test showed temperature dependance, but reaction order did not. The order of reaction (m+n) was calculated to be close to 3. The measurements of viscosity and relation time in the presence of inorganic fillers were carried out at different isothermal curing temperatures. The viscosity and gelation time increased with filler content at the same isothermal temperature.

• 천문학회보
• /
• 제36권1호
• /
• pp.55.2-55.2
• /
• 2011

Many astrophysical high energy phenomena involve relativistic flows. We describe codes for adiabatic and isothermal flows in relativistic regimes. For adiabatic flows, we employ an equation of state (EOS) which is simple and yet approximates very closely the EOS of the single-component perfect gas. For isothermal flows, we use an EOS of constant sound speed. We present the eigenstructures of relativistic hydrodynamics which can be used to build numerical codes, and discuss the calculation of primitive variables from conservative ones for both adiabatic and isothermal flows. The shock tube tests show differences between the two flows.

• 한국주조공학회지
• /
• 제25권6호
• /
• pp.249-253
• /
• 2005

The present study focuses on 7075 aluminum wrought alloy to investigate the potential industrial applications of thixoextrusion process. The microstructural evolution of 7075 aluminum wrought alloy for thixoextrusion has been investigated as a function of isothermal holding temperature and time in the partially remelted semisolid state. The results showed that the liquid fraction increased with increasing isothermal holding temperature and time while the average grain size was inversely proportional to isothermal holding temperature and time up to 5min. However, there was no big change of liquid fraction and average grain size with respect to isothermal holding temperature and time. The important fact that the liquid fraction and average grain size were almost uniform after 5 min holding time is considered very useful for thixoextrusion in terms of process control.

• 드라이브 ㆍ 컨트롤
• /
• 제10권4호
• /
• pp.29-33
• /
• 2013

Pneumatic system is widely applied in various industry because it have a many advantage(low cost, high safety, etc..). For design of pneumatic system, accurate flow measurement is required. In this study, compressible fluid flow measurement apparatus was designed and built. It uses an isothermal chamber that can approximate isothermal condition. Therefore, it can be measured for flow-rate using pressure response of isothermal chamber. As a result, this apparatus can be measured for sonic conductance and critical pressure ratio of pneumatic components and it required less time and energy than conventional flow meter. The effectiveness of the designed apparatus is proved by experimental result.

• 열처리공학회지
• /
• 제11권3호
• /
• pp.192-199
• /
• 1998

This study was carried out to investigate the influence of variations in the temperature and time of isothermal heat treatment, applied stresses and prestrain on the isothermal transformation behavior of ${\gamma}$ and ${\sigma}$ phases and mechanical properties of 25Cr-7Ni-3Mo duplex stainless steel. The precipitation of ${\gamma}$ and ${\sigma}$ phases through isothermal heat treatment showed the type curves with a certain incubation period, the curve migrated to in a short period of time and the amount of precipitation increased with decreasing isothermal heat treatment temperature. Under the state of isothermal transformation, the precipitation of ${\gamma}$ and ${\sigma}$ phases was stimulated by applied stress, with increasing applied stress, the curves migrated to in a short period of time and also observed that the application of stress has a greater influence on the amount of ${\sigma}$ precipitation than that of ${\gamma}$ precipitation. The precipitation of ${\gamma}$ and ${\sigma}$ phases was stimulated by cold and warm rolling before isothermal heat treatment and precipitation of ${\gamma}$ and ${\sigma}$ phases has a greater influence on the warm rolling than cold rolling. The tensile strength and hardness increased with increasing cold and warm rooling reduction ratio.

• 한국결정성장학회지
• /
• 제24권4호
• /
• pp.151-157
• /
• 2014

The degradation mechanisms of thermal barrier coatings (TBCs) were investigated in different thermal fatigue condition in terms of microstructural analyses. The isothermal and cyclic oxidation tests were conducted to atmospheric plasma sprayed-TBCs on NIMONIC 263 substrates. The delamination occurred by the oxide layer formation at the interface, the Ni/Cr-based oxide was formed after Al-based oxide layer grew up to ${\sim}10{\mu}m$ in the isothermal condition. In the cyclic oxidation with dwell time, the failure occurred earlier (500 hr) than in the isothermal oxidation (900 hr) at same temperature. The thickness of Al-based oxide layer of the delaminated specimen in the cyclic condition was ${\sim}4{\mu}m$ and the interfacial cracks were observed. The acoustic emission method revealed that the cracks generated during the cooling step. It was considered that the specimens were prevented from the formation of the Al-based oxide by cooling treatment, and the degradation mode in the cyclic test was dominantly interfacial cracking by the difference of thermal expansion coefficients of the coating layers.